Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM › 2014.08–2015.08
RM2660E _51 Engine / Hybrid System _052774 1GR-FE ENGINE CONTROL _0255001 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P2431  Secondary Air Injection System Air Flow / Pressure Sensor Circuit Range / Performance Bank1  P2432  Secondary Air Injection System Air Flow / Pressure Sensor Circuit Low Bank1  P2433  Secondary Air Injection System Air Flow / Pressure Sensor Circuit High Bank1  P2436  Secondary Air Injection System Air Flow / Pressure Sensor Circuit Range / Performance Bank 2  P2437  Secondary Air Injection System Air Flow / Pressure Sensor Circuit Low Bank 2  P2438  Secondary Air Injection System Air Flow / Pressure Sensor Circuit High Bank 2  


DESCRIPTION

Refer to DTC P0412 (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>P0412).

Refer to DTC P0416 (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>P0416).

DTC No. DTC Detection Condition Trouble Area
P2431
P2436
Pressure sensor indicates a value below 45.6 kPa (342 mmHg), or higher than 135 kPa (1013 mmHg) (2 trip detection logic).
·

Emission control valve set

·

Open or short in pressure sensor circuit

·

ECM


P2432
P2437
While the engine is running, the voltage output of the pressure sensor is below 0.5 V (1 trip detection logic).
·

Emission control valve set

·

Open or short in pressure sensor circuit

·

ECM


P2433
P2438
While the engine is running, the voltage output of the pressure sensor is higher than 4.5 V (1 trip detection logic).
·

Emission control valve set

·

Open or short in pressure sensor circuit

·

ECM



MONITOR DESCRIPTION

A085160E39
0.073,2.771 1.125,2.948 1.052,0.177 10 false Pressure Sensor 2.594,2.927 2.917,3.104 0.323,0.177 10 false ECM 2.292,0.833 2.688,1.01 0.396,0.177 10 false VCV2 2.292,1.479 2.531,1.656 0.24,0.177 10 false AIP 0.833,1.615 1.073,1.792 0.24,0.177 10 false AIP 2.292,2.094 2.833,2.271 0.542,0.177 10 false ETHA 0.865,1.031 1.073,1.208 0.208,0.177 10 false VC 0.875,2.208 1.063,2.385 0.188,0.177 10 false E2 0.083,0.042 2.156,0.271 2.073,0.229 12 false Reference (for Bank 1):

The ECM monitors the pressure in the secondary air passage using the pressure sensor located on the emission control valve set in the secondary air injection system. Using this pressure value, the ECM determines whether the secondary air injection system is malfunctioning or not.

If there is a defect in the sensor or the sensor circuit, the voltage level deviates from the normal operating range. The ECM interprets this deviation as a malfunction in the pressure sensor or circuit and stores a DTC.

WIRING DIAGRAM

A162276E12
1.323,1.192 1.556,1.362 0.232,0.170 10 VC 1.665,1.368 1.815,1.518 0.149,0.149 10 2 1.281,1.76 1.555,1.930 0.274,0.170 10 AIP 5.655,1.192 6.063,1.362 0.408,0.170 10 VCV2 5.655,1.76 5.929,1.930 0.274,0.170 10 AIP 1.665,1.936 1.815,2.085 0.149,0.149 10 3 1.344,2.313 1.556,2.483 0.211,0.170 10 E2 1.665,2.489 1.815,2.638 0.149,0.149 10 4 0.32,2.802 0.693,2.970 0.373,0.168 10 C137 0.32,2.972 2.408,3.151 2.088,0.180 10 No. 1 Emission Control Valve Set 0.32,5.496 2.415,5.675 2.095,0.180 10 No. 2 Emission Control Valve Set 1.274,3.714 1.636,3.884 0.362,0.170 10 VC2 1.665,3.89 1.815,4.039 0.149,0.149 10 2 1.223,4.282 1.555,4.451 0.332,0.170 10 AIP2 1.665,4.458 1.815,4.607 0.149,0.149 10 3 1.251,4.835 1.555,5.005 0.304,0.170 10 E22 1.665,5.011 1.815,5.160 0.149,0.149 10 4 0.32,5.327 0.686,5.495 0.366,0.168 10 C138 5.354,1.104 5.533,1.283 0.179,0.179 10 66 5.313,1.273 5.600,1.430 0.288,0.157 10 C45 5.361,1.678 5.540,1.857 0.179,0.179 10 54 5.313,1.843 5.600,1.999 0.288,0.157 10 A38 5.655,4.282 6.003,4.451 0.348,0.170 10 AIP2 5.364,4.193 5.543,4.371 0.179,0.179 10 53 5.313,4.365 5.600,4.521 0.288,0.157 10 A38 5.655,4.827 6.052,4.997 0.396,0.170 10 ETHA 6.053,5.804 6.428,5.973 0.376,0.170 10 ECM 5.365,4.731 5.544,4.910 0.179,0.179 10 98 5.313,4.907 5.600,5.063 0.288,0.157 10 C45

CAUTION / NOTICE / HINT

HINT:
·

Refer to "Data List / Active Test" [Air Pump Pressure (Absolute) and Air Pump2 Pressure (Absolute)] (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>DATA LIST / ACTIVE TEST).

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

Bank 1 refers to the bank that includes the No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from the transmission.

·

Bank 2 refers to the bank that does not include the No. 1 cylinder.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (EMISSION CONTROL VALVE SET - ECM)
a.

Disconnect the emission control valve set connector.


b.

Disconnect the ECM connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C137-3 (AIP) - A38-54 (AIP) Always Below 1 Ω
C137-2 (VC) - C45-66 (VCV2) Always Below 1 Ω
C137-4 (E2) - C45-98 (ETHA) Always Below 1 Ω
C138-3 (AIP2) - A38-53 (AIP2) Always Below 1 Ω
C138-2 (VC2) - C45-66 (VCV2) Always Below 1 Ω
C138-4 (E22) - C45-98 (ETHA) Always Below 1 Ω
C137-3 (AIP) or A38-54 (AIP) - Body ground Always 10 kΩ or higher
C137-2 (VC) or C45-66 (VCV2) - Body ground Always 10 kΩ or higher
C138-3 (AIP2) or A38-53 (AIP2) - Body ground Always 10 kΩ or higher
C138-2 (VC2) or C45-66 (VCV2) - Body ground Always 10 kΩ or higher




OK

2.CHECK TERMINAL VOLTAGE (VC OF EMISSION CONTROL VALVE SET)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK TERMINAL VOLTAGE (VC OF EMISSION CONTROL VALVE SET)
U163334E01
0.153,0.147 0.359,0.338 0.206,0.192 10 *a 0.173,0.876 0.530,1.039 0.357,0.163 10 C137 0.17,1.216 0.528,1.378 0.357,0.163 10 C138 0.675,0.874 0.876,1.047 0.201,0.173 10 *A 0.675,1.213 0.876,1.386 0.201,0.173 10 *B 0.871,1.676 1.249,1.832 0.378,0.156 10 VC*A 0.871,1.891 1.311,2.047 0.440,0.156 10 VC2*B 2.109,1.676 2.486,1.832 0.378,0.156 10 E2*A 2.109,1.891 2.549,2.047 0.440,0.156 10 E22*B 1.537,1.131 1.069,1.655 false 1.856,1.134 2.242,1.655 false

a.

Disconnect the emission control valve set connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C137-2 (VC) - C137-4 (E2) Ignition switch ON 4.5 to 5.5 V
C138-2 (VC2) - C138-4 (E22) Ignition switch ON 4.5 to 5.5 V


Text in Illustration
*A for Bank 1
*B for Bank 2
*a Front view of wire harness connector
(to Emission Control Valve Set)



OK

3.REPLACE EMISSION CONTROL VALVE SET

NG

3.REPLACE EMISSION CONTROL VALVE SET
a.

Replace the emission control valve set.

HINT:
·
·




NEXT

4.CHECK WHETHER DTC OUTPUT RECURS
4.CHECK WHETHER DTC OUTPUT RECURS
a.

Start the engine and warm it up.


b.

Turn the ignition switch off.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.



g.

Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Automatic Mode.


h.

Start the engine after the GTS initialization is finished.


i.

Perform the System Check operation by pressing ENTER (Next).


j.

Perform the following to confirm the secondary air injection system pending codes: Press the Exit button.


k.

Check for pending DTCs.

OK:

No pending DTC is output.



l.

Turn the ignition switch off.

NOTICE:
·

When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the ignition switch turned to ON or the engine running.

·

Turn the ignition switch off when the Secondary Air Injection Check operation finishes.





OK

END

NG