Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM › 2015.08–2017.08
RM2660E _51 Engine / Hybrid System _052774 1GR-FE ENGINE CONTROL _0255001 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P0365  Camshaft Position Sensor "B" Circuit (Bank 1)  P0367  Camshaft Position Sensor "B" Circuit Low Input (Bank 1)  P0368  Camshaft Position Sensor "B" Circuit High Input (Bank 1)  P0390  Camshaft Position Sensor "B" Circuit (Bank 2)  P0392  Camshaft Position Sensor "B" Circuit Low Input (Bank 2)  P0393  Camshaft Position Sensor "B" Circuit High Input (Bank 2)  


DESCRIPTION

The exhaust camshaft's Variable Valve Timing (VVT) sensor (EV1, EV2 signal) consists of a magnet and MRE (Magnetoresistive Element).

The exhaust camshaft has 3 teeth on its outer circumference.

When the exhaust camshaft rotates, changes occur in the air gaps between the 3 teeth and MRE, which affects the magnetic field. As a result, the resistance of the MRE material fluctuates. The VVT sensor converts the exhaust camshaft rotation data to pulse signals, uses the pulse signals to determine the camshaft angle, and sends the camshaft angle data to the ECM.

DTC No. DTC Detection Condition Trouble Area
P0365
P0390
There is no VVT sensor signal despite the crankshaft position sensor input being normal at an engine speed of 600 rpm or more (1 trip detection logic).
·

Open or short in VVT sensor (for exhaust side) circuit

·

VVT sensor (for exhaust side)

·

Exhaust camshaft

·

Timing chain has jumped tooth

·

ECM


P0367
P0392
Output voltage of the VVT sensor is below 0.3 V for 4 seconds (1 trip detection logic).
·

Open or short in VVT sensor (for exhaust side) circuit

·

VVT sensor (for exhaust side)

·

Exhaust camshaft

·

Timing chain has jumped tooth

·

ECM


P0368
P0393
Output voltage of the VVT sensor is higher than 4.7 V for 4 seconds (1 trip detection logic).
·

Open or short in VVT sensor (for exhaust side) circuit

·

VVT sensor (for exhaust side)

·

Exhaust camshaft

·

Timing chain has jumped tooth

·

ECM



A228079E01
1.063,2.829 2.046,3.030 0.983,0.201 10 20 msec./DIV. 0.088,0.811 0.651,0.977 0.563,0.166 10 5 V/DIV. 0.195,1.477 0.479,1.678 0.284,0.201 10 NE 0.11,1.975 0.477,2.176 0.367,0.201 10 EV1 3.031,1.494 3.363,1.695 0.332,0.201 10 GND 3.031,2.095 3.363,2.296 0.332,0.201 10 GND 3.031,2.491 3.363,2.692 0.332,0.201 10 GND 0.11,2.37 0.477,2.571 0.367,0.201 10 EV2 0.35,0.274 2.756,0.475 2.406,0.201 10 EV1, EV2 and NE Signal Waveforms

Reference: Inspection using an oscilloscope

HINT:
·

The correct waveforms are as shown.

·

EV1 and EV2 are the VVT sensor signal, and NE is the crankshaft position sensor signal.

Item Content
Terminal NE+ - NE-
EV1+ - EV1-
EV2+ - EV2-
Equipment Setting 5 V/DIV.
20 msec./DIV.
Condition Cranking or idling




MONITOR DESCRIPTION

If no signal is transmitted by the VVT sensor despite the camshaft revolving, or the rotations of the camshaft and crankshaft are not synchronized, the ECM interprets this as a malfunction of the sensor.

WIRING DIAGRAM

A160377E24
0.583,2.24 0.917,2.417 0.333,0.177 10 false C121 0.583,2.406 3.177,2.615 2.594,0.208 10 false VVT Sensor (for Exhaust Side of Bank 1) 0.583,3.885 0.927,4.083 0.344,0.198 10 false C122 0.583,4.042 3.135,4.281 2.552,0.24 10 false VVT Sensor (for Exhaust Side of Bank 2) 1.448,1.198 1.771,1.406 0.323,0.208 10 false VC2 1.844,1.302 1.99,1.479 0.146,0.177 10 false 3 4.813,1.313 5.094,1.49 0.281,0.177 10 false 67 4.813,1.688 5.052,1.865 0.24,0.177 10 false 69 4.823,2.052 5.063,2.229 0.24,0.177 10 false 68 1.469,1.583 1.729,1.781 0.26,0.198 10 false EX+ 1.844,1.667 1.99,1.844 0.146,0.177 10 false 1 1.469,1.948 1.74,2.135 0.271,0.188 10 false EX- 5.125,1.198 5.594,1.354 0.469,0.156 10 false VCV1 5.125,1.583 5.521,1.74 0.396,0.156 10 false EV1+ 5.125,1.948 5.49,2.135 0.365,0.188 10 false EV1- 4.823,2.969 5.094,3.146 0.271,0.177 10 false 66 4.823,3.344 5.063,3.521 0.24,0.177 10 false 64 4.823,3.719 5.063,3.896 0.24,0.177 10 false 65 5.125,2.865 5.594,3.021 0.469,0.156 10 false VCV2 5.125,3.25 5.521,3.406 0.396,0.156 10 false EV2+ 5.125,3.615 5.49,3.802 0.365,0.188 10 false EV2- 1.844,2.073 1.99,2.25 0.146,0.177 10 false 2 1.844,2.958 1.99,3.135 0.146,0.177 10 false 3 1.833,3.323 1.979,3.5 0.146,0.177 10 false 1 1.844,3.708 1.99,3.885 0.146,0.177 10 false 2 5.365,4.25 6.365,4.427 1,0.177 10 false C45*1, C46*2 5.365,4.396 5.729,4.552 0.365,0.156 10 false ECM 1.448,2.844 1.771,3.052 0.323,0.208 10 false VC2 1.448,3.208 1.708,3.406 0.26,0.198 10 false EX+ 1.448,3.594 1.719,3.781 0.271,0.188 10 false EX- 3.656,4.104 4.448,4.281 0.792,0.177 10 false *1: for LHD 3.656,4.354 4.448,4.531 0.792,0.177 10 false *2: for RHD

CAUTION / NOTICE / HINT

HINT:
·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

Bank 1 refers to the bank that includes the No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from the transmission.

·

Bank 2 refers to the bank that does not include the No. 1 cylinder.



PROCEDURE

1.CHECK TERMINAL VOLTAGE (SENSOR POWER SOURCE)
a.
U163312E01
0.339,0.962 0.699,1.127 0.359,0.165 10 C121 0.339,1.298 0.699,1.462 0.359,0.165 10 C122 2.317,1.684 2.774,1.847 0.457,0.163 10 VC2 0.079,0.042 0.269,0.205 0.190,0.163 10 *a 0.853,0.962 1.043,1.125 0.190,0.163 10 *A 0.853,1.298 1.043,1.460 0.190,0.163 10 *B 1.96,1.346 2.274,1.674 false

Disconnect the VVT sensor connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C121-3 (VC2) - Body ground Ignition switch ON 4.5 to 5.0 V
C122-3 (VC2) - Body ground Ignition switch ON 4.5 to 5.0 V


Text in Illustration
*A for Bank 1
*B for Bank 2
*a Front view of wire harness connector
(to VVT Sensor)



OK

2.CHECK HARNESS AND CONNECTOR (VVT SENSOR - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (VVT SENSOR - ECM)
a.

Disconnect the VVT sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
C121-1 (EX+) - C45-69 (EV1+) Always Below 1 Ω
C121-2 (EX-) - C45-68 (EV1-) Always Below 1 Ω
C122-1 (EX+) - C45-64 (EV2+) Always Below 1 Ω
C122-2 (EX-) - C45-65 (EV2-) Always Below 1 Ω
C121-1 (EX+) or C45-69 (EV1+) - Body ground Always 10 kΩ or higher
C121-2 (EX-) or C45-68 (EV1-) - Body ground Always 10 kΩ or higher
C122-1 (EX+) or C45-64 (EV2+) - Body ground Always 10 kΩ or higher
C122-2 (EX-) or C45-65 (EV2-) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
C121-1 (EX+) - C46-69 (EV1+) Always Below 1 Ω
C121-2 (EX-) - C46-68 (EV1-) Always Below 1 Ω
C122-1 (EX+) - C46-64 (EV2+) Always Below 1 Ω
C122-2 (EX-) - C46-65 (EV2-) Always Below 1 Ω
C121-1 (EX+) or C46-69 (EV1+) - Body ground Always 10 kΩ or higher
C121-2 (EX-) or C46-68 (EV1-) - Body ground Always 10 kΩ or higher
C122-1 (EX+) or C46-64 (EV2+) - Body ground Always 10 kΩ or higher
C122-2 (EX-) or C46-65 (EV2-) - Body ground Always 10 kΩ or higher




OK

3.CHECK SENSOR INSTALLATION (VVT SENSOR FOR EXHAUST CAMSHAFT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK SENSOR INSTALLATION (VVT SENSOR FOR EXHAUST CAMSHAFT)
a.
A385403E03
0.354,1.792 1.271,1.99 0.917,0.198 10 false Normal 2.49,1.792 3.406,1.99 0.917,0.198 10 false Abnormal 1.5,1.563 2.677,2 1.177,0.438 10 false Clearance

Check the VVT sensor installation.

OK:

Sensor is installed correctly.




OK

4.CHECK EXHAUST CAMSHAFT

NG

4.CHECK EXHAUST CAMSHAFT
a.

Check the teeth of the camshaft.


OK:

Teeth do not have any cracks or deformation.



OK

5.REPLACE VVT SENSOR

NG

5.REPLACE VVT SENSOR

NEXT

6.CHECK WHETHER DTC OUTPUT RECURS
6.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.



e.

Start the engine.


f.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


g.

Read the DTCs.

Result
Result Proceed to
No DTC is output A
P0365, P0367, P0368, P0390, P0392 or P0393 is output B

HINT:

If the engine does not start, replace the ECM.




A

END

B