16711
1.REMOVE FAN SHROUD
17129
2.REMOVE INTAKE AIR SURGE TANK
17361
3.REMOVE AIR TUBE (w/ Secondary Air Injection System)
17362
4.REMOVE NO. 2 AIR TUBE (w/ Secondary Air Injection System)
25701B
5.REMOVE NO. 1 EMISSION CONTROL VALVE SET (w/ Secondary Air Injection System)
25702B
6.REMOVE NO. 2 EMISSION CONTROL VALVE SET (w/ Secondary Air Injection System)
19500
7.REMOVE IGNITION COIL ASSEMBLY
44310
8.DISCONNECT VANE PUMP ASSEMBLY
16604
9.REMOVE NO. 2 IDLER PULLEY SUB-ASSEMBLY
17168
10.REMOVE NO. 2 EXHAUST MANIFOLD HEAT INSULATOR
27020
11.REMOVE GENERATOR ASSEMBLY
11452
12.REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE
16206
13.REMOVE WATER BY-PASS PIPE SUB-ASSEMBLY
15771
14.REMOVE NO. 1 OIL PIPE
15772
15.REMOVE NO. 2 OIL PIPE
16.DISCONNECT FUEL PIPE SUB-ASSEMBLY
11202
17.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY LH
11201
18.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY
11324
19.REMOVE TIMING CHAIN COVER PLATE
Remove the 4 bolts, timing chain cover plate and gasket.
20.SET NO. 1 CYLINDER TO TDC/COMPRESSION
Turn the crankshaft pulley and align the notch with the "0" timing mark of the timing chain cover.
Check that the timing marks of the camshaft timing gears are aligned with the timing marks of the bearing caps as shown in the illustration.
| *A | for Bank 2 |
| *B | for Bank 1 |
| *1 | Paint Mark |
If the marks are not aligned, turn the crankshaft again to align the marks.
Place paint marks on the timing marks and sprockets of each camshaft timing gear and on the links of the No. 1 chain.
Be sure to place the paint marks on 2 links of the chain and on the sprockets of the camshaft timing gears at the locations of the timing marks of the camshaft timing gears.
13540
21.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY
Turn the crankshaft approximately 30° counterclockwise so that there is some slack in the chain.
This prevents the valves and pistons from interfering with each other.
Align the hole in the lever of the tensioner with the hole in the tensioner body as shown in the illustration, and then insert a pin with a diameter of 1.27 mm (0.0500 in.) into the hole.
| *1 | Lever Hole |
| *2 | Tensioner Hole |
Turn the crankshaft clockwise and align the notch with the "0" timing mark of the timing chain cover.
Remove the 2 bolts and chain tensioner.
Do not drop the No. 1 chain tensioner assembly or bolts into the timing chain cover.
13506
22.DISCONNECT CHAIN SUB-ASSEMBLY (for Bank 1)
Turn the crankshaft clockwise until it is in the position shown in the illustration so that there is some slack in the chain between the banks.
As the camshafts turn suddenly, do not touch the camshafts or camshaft timing gears.
When turning the crankshaft, engine oil may spray out of the oil holes.
Turn the crankshaft clockwise until it is in the position shown in the illustration so that the chain can be removed easily.
| *a | 5° to 10° |
When turning the crankshaft, engine oil may spray out of the oil holes.
Remove the chain from the sprocket of the camshaft timing gear and set it on the gear.
As the camshaft may turn suddenly and pinch your fingers when the chain is removed, pinch the chain and lift it upward to remove it from the sprocket.
23.REMOVE CAMSHAFT BEARING CAP (for Bank 1)
Remove the bolts and bearing caps in the order shown in the illustration. Immediately after removing a bearing cap, install bolts and washers for temporary installation of the camshaft housing in the order shown in the illustration.
| *1 | Bolt |
| *2 | Washer |
| *a | Part Removal |
| *b | Installation of Bolts and Washers for Temporary Installation of Camshaft Housing |
Do not install the bearing caps when installing bolts and washers for temporary installation of the camshaft housing.
Be sure to follow the numerical order when performing this procedure.
Do not allow bolts and washers for temporary installation of the camshaft housing to contact the camshaft.
Do not drop bolts and washers for temporary installation of the camshaft housing into the cylinder head.
Arrange the removed parts so that they can be reinstalled in their original locations.
Part number of bolt for temporary installation of camshaft housing: 91551-G0845 (quantity: 8)
Part number of washer for temporary installation of camshaft housing: 90201-12028 (quantity: 16)
13512
24.REMOVE NO. 2 CAMSHAFT
Remove the bolt of the No. 2 chain tensioner assembly.
Remove the No. 2 chain tensioner assembly while lifting up the No. 2 camshaft.
While lifting up the No. 2 camshaft, pass it through the No. 2 chain and pull it out towards the front of the vehicle to remove it.
13511
25.REMOVE CAMSHAFT
Lift up the rear of the camshaft so that it is at an angle.
Remove the chain from the camshaft timing gear and pull out the camshaft and No. 2 chain towards the rear of the vehicle to remove them.
Do not drop the chain into the gap between the engine and cover.
Suspend the chain with a string or equivalent.
13506
26.DISCONNECT CHAIN SUB-ASSEMBLY (for Bank 2)
Turn the crankshaft counterclockwise and align the notch with the "0" timing mark of the timing chain cover.
Remove the chain from the sprocket of the camshaft timing gear and set it on the gear.
As the camshaft may turn suddenly and pinch your fingers when the chain is removed, pinch the chain and lift it upward to remove it from the sprocket.
27.REMOVE CAMSHAFT BEARING CAP (for Bank 2)
Remove the bolts and bearing caps in the order shown in the illustration. Immediately after removing a bearing cap, install bolts and washers for temporary installation of the camshaft housing in the order shown in the illustration.
| *1 | Bolt |
| *2 | Washer |
| *a | Part Removal |
| *b | Installation of Bolts and Washers for Temporary Installation of Camshaft Housing |
Do not install the bearing caps when installing bolts and washers for temporary installation of the camshaft housing.
Be sure to follow the numerical order when performing this procedure.
Do not allow bolts and washers for temporary installation of the camshaft housing to contact the camshaft.
Do not drop bolts and washers for temporary installation of the camshaft housing into the cylinder head.
Arrange the removed parts so that they can be reinstalled in their original locations.
Part number of bolt for temporary installation of camshaft housing: 91551-G0845 (quantity: 8)
Part number of washer for temporary installation of camshaft housing: 90201-12028 (quantity: 16)
13054
28.REMOVE NO. 4 CAMSHAFT SUB-ASSEMBLY
Remove the bolt of the No. 3 chain tensioner assembly.
Remove the No. 3 chain tensioner assembly while lifting up the No. 4 camshaft.
While lifting up the No. 4 camshaft, pass it through the No. 2 chain and pull it out towards the front of the vehicle to remove it.
13053
29.REMOVE NO. 3 CAMSHAFT SUB-ASSEMBLY
Lift up the rear of the camshaft so that it is at an angle.
Remove the chain from the camshaft timing gear and pull out the No. 3 camshaft and No. 2 chain towards the rear of the vehicle to remove them.
Do not drop the chain into the gap between the engine and cover.
Suspend the chain with a string or equivalent.
13050
30.REMOVE CAMSHAFT TIMING GEAR ASSEMBLY
Fix the camshaft in place.
Be careful not to damage the camshaft.
Remove the flange bolt and camshaft timing gear assembly.
| *1 | Do not remove |
| *2 | Straight Pin |
| *3 | Flange Bolt |
Do not remove the other 3 bolts.
If planning to reuse the camshaft timing gear, be sure to release the straight pin lock before installing the camshaft timing gear.
13070A
31.REMOVE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY
Fix the camshaft in place.
Be careful not to damage the camshaft.
Remove the flange bolt and camshaft timing exhaust gear assembly.
| *1 | Do not remove |
| *2 | Straight Pin |
| *3 | Flange Bolt |
Be sure not to remove the other 4 bolts.
If planning to reuse the gear, be sure to release the straight pin lock before installing the gear.