Home › Engine / Hybrid System › 3UR-FE (ENGINE CONTROL) › SFI SYSTEM(w/o Secondary Air Injection System) › 2014.08–2015.08
RM2660E _51 Engine / Hybrid System _052775 3UR-FE ENGINE CONTROL _0255032 SFI SYSTEM J

3UR-FE ENGINE CONTROL  SFI SYSTEM  ECM Power Source Circuit  


DESCRIPTION

When the engine switch is turned on (IG), battery voltage is applied to the IGSW of the ECM. The output signal from the MREL terminal of the ECM causes a current to flow to the coil, closing the contacts of the integration relay (EFI) and supplying power to either terminal +B or +B2 of the ECM.

WIRING DIAGRAM

A182334E09
0.604,3.903 1.086,4.088 0.482,0.185 10 Battery 3.236,0.426 3.598,0.620 0.362,0.193 10 IG2D 3.663,0.318 3.871,0.495 0.208,0.177 10 11 2.391,0.827 2.682,0.989 0.291,0.163 10 E2 2.391,0.974 3.462,1.137 1.071,0.163 10 Main Body ECU 1.545,3.345 1.672,3.522 0.127,0.177 10 3 1.496,3.506 1.709,3.668 0.212,0.162 10 1B 2.393,4.281 3.519,4.472 1.127,0.191 10 Integration Relay 1.545,1.747 1.672,1.924 0.127,0.177 10 1 2.355,1.766 2.482,1.943 0.127,0.177 10 1 2.615,1.766 2.742,1.943 0.127,0.177 10 2 2.355,2.995 2.482,3.172 0.127,0.177 10 1 2.615,2.995 2.742,3.172 0.127,0.177 10 2 1.496,1.908 1.709,2.070 0.212,0.162 10 1C 4.175,3.337 4.302,3.514 0.127,0.177 10 2 4.127,3.501 4.340,3.664 0.212,0.162 10 1B 4.175,2.967 4.302,3.144 0.127,0.177 10 4 4.127,3.127 4.340,3.289 0.212,0.162 10 1B 4.175,2.121 4.302,2.298 0.127,0.177 10 6 4.127,2.282 4.340,2.444 0.212,0.162 10 1B 4.175,2.508 4.302,2.685 0.127,0.177 10 7 4.127,2.668 4.340,2.830 0.212,0.162 10 1B 4.175,1.743 4.302,1.920 0.127,0.177 10 8 4.127,1.907 4.340,2.070 0.212,0.162 10 1B 5.553,1.747 5.732,1.924 0.180,0.177 10 28 5.503,1.907 5.783,2.070 0.280,0.162 10 A38 2.26,3.282 2.947,3.462 0.687,0.180 10 EFI MAIN 3.509,3.833 3.802,4.000 0.293,0.167 10 EFI 3.52,1.592 3.813,1.758 0.293,0.167 10 IG2 2.255,2.057 2.899,2.225 0.644,0.168 10 IG2 MAIN 4.888,1.764 5.015,1.941 0.127,0.177 10 1 5.144,1.764 5.271,1.941 0.127,0.177 10 2 4.935,2.029 5.240,2.197 0.304,0.168 10 IGN 5.847,1.803 6.262,1.966 0.415,0.163 10 IGSW 5.595,2.603 5.733,2.780 0.137,0.177 10 3 5.503,2.764 5.783,2.926 0.280,0.162 10 A38 5.847,2.763 6.066,2.926 0.219,0.163 10 +B 5.595,2.954 5.733,3.130 0.137,0.177 10 2 5.503,3.114 5.783,3.276 0.280,0.162 10 A38 5.847,3.113 6.163,3.276 0.316,0.163 10 +B2 5.548,3.332 5.748,3.509 0.200,0.177 10 34 5.503,3.496 5.783,3.658 0.280,0.162 10 A38 5.847,3.491 6.254,3.654 0.407,0.163 10 MREL 5.548,3.874 5.748,4.051 0.200,0.177 10 81 5.503,4.035 5.783,4.197 0.280,0.162 10 C45 5.847,4.034 6.101,4.197 0.254,0.163 10 E1 6.17,4.563 6.527,4.714 0.357,0.151 10 ECM

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.INSPECT INTEGRATION RELAY (INTEGRATION RELAY - BODY GROUND)
U163739E01
0.08,0.069 2.451,0.399 2.371,0.330 10 Front view of wire harness connector: (to Integration Relay) 2.701,1.365 3.058,1.528 0.356,0.163 10 1C 2.84,2.081 3.047,2.562 false 3.011,2.602 3.168,2.765 0.157,0.163 10 1

a.

Remove the integration relay from the engine room relay block.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
1C-1 - Body ground Always 11 to 14 V




OK

2.INSPECT INTEGRATION RELAY (EFI AND IG2 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT INTEGRATION RELAY (EFI AND IG2 RELAY)
U151425E04
0.135,0.156 2.646,0.521 2.51,0.365 10 false Component without harness connected: (Integration Relay) 0.479,2.417 0.708,2.563 0.229,0.146 10 false 1C 1.333,2.417 1.521,2.563 0.188,0.146 10 false 1B 2.438,2.417 2.625,2.563 0.188,0.146 10 false 1A

a.

Remove the integration relay from the engine room relay block.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1C-1 - 1B-4 Battery voltage is not applied to terminals 1B-2 and 1B-3 10 kΩ or higher
Battery voltage is applied to terminals 1B-2 and 1B-3 Below 1 Ω
1C-1 - 1B-8 Battery voltage is not applied to terminals 1B-7 and 1B-6 10 kΩ or higher
Battery voltage is applied to terminals 1B-7 and 1B-6 Below 1 Ω




OK

3.CHECK HARNESS AND CONNECTOR (+B, +B2 AND MREL CIRCUIT)

NG

REPLACE INTEGRATION RELAY

3.CHECK HARNESS AND CONNECTOR (+B, +B2 AND MREL CIRCUIT)
U163740E02
1.865,1.552 2.073,1.823 true 1.781,1.552 1.76,1.823 true 1.719,1.552 1.5,1.823 true 1.76,3.094 1.448,4.188 true 1.854,3.104 2.063,4.156 true 1.979,3.479 2.823,4.219 true 0.115,2.177 2.49,2.51 2.375,0.333 10 false Front view of wire harness connector: (to ECM) 0.125,0.063 2.542,0.396 2.417,0.333 10 false Front view of wire harness connector: (to Integration Relay) 1.833,0.979 2.125,1.146 0.292,0.167 10 false 1B 0.313,3.26 0.604,3.427 0.292,0.167 10 false A38 2.073,1.844 2.229,2 0.156,0.156 10 false 4 1.719,1.833 1.885,2.021 0.167,0.188 10 false 3 1.427,1.823 1.583,1.979 0.156,0.156 10 false 2 1.156,4.208 1.646,4.365 0.49,0.156 10 false 2 (+B2) 1.854,4.198 2.313,4.354 0.458,0.156 10 false 3 (+B) 2.5,4.208 3.229,4.365 0.729,0.156 10 false 34 (MREL)

a.

Check the harness and the connectors between the integration relay and the ECM.

i.

Remove the integration relay from the engine room relay block.


ii.

Disconnect the ECM connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A38-34 (MREL) - 1B-2 Always Below 1 Ω
A38-3 (+B) - 1B-4 Always Below 1 Ω
A38-2 (+B2) - 1B-4 Always Below 1 Ω
A38-34 (MREL) or 1B-2 - Body ground Always 10 kΩ or higher
A38-3 (+B) or 1B-4 - Body ground Always 10 kΩ or higher
A38-2 (+B2) or 1B-4 - Body ground Always 10 kΩ or higher




b.

Check the harness and connectors between the integration relay and body ground.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1B-3 - Body ground Always Below 1 Ω





OK

4.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)
A385737E03
1.99,2.208 2.396,2.823 true 0.292,0.104 2.604,0.635 2.313,0.531 10 false Front view of wire harness connector: (to ECM) 1.583,1.146 1.99,1.385 0.406,0.24 10 false C45 2.208,2.865 2.875,3.146 0.667,0.281 10 false 81 (E1)

a.

Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C45-81 (E1) - Body ground Always Below 1 Ω




OK

5.INSPECT ECM (IGSW VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT ECM (IGSW VOLTAGE)
A385741E01
1.99,2.052 2.427,2.625 true 2.24,3.823 2.771,4.156 true 0.25,0.073 2.542,0.458 2.292,0.385 10 false Front view of wire harness connector: (to ECM) 1.625,0.969 1.948,1.146 0.323,0.177 10 false C45 1.625,2.969 1.948,3.146 0.323,0.177 10 false A38 2.375,2.635 2.833,2.885 0.458,0.25 10 false 81(E1) 2.708,4.188 3.354,4.5 0.646,0.313 10 false 28 (IGSW)

a.

Disconnect the ECM connectors.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A38-28 (IGSW) - C45-81 (E1) Engine switch on (IG) 11 to 14 V




OK

NG

6.CHECK HARNESS AND CONNECTOR (INTEGRATION RELAY - ECM, INTEGRATION RELAY - BODY GROUND)
6.CHECK HARNESS AND CONNECTOR (INTEGRATION RELAY - ECM, INTEGRATION RELAY - BODY GROUND)
U163741E01
0.063,2.083 2.434,2.413 2.371,0.330 10 Front view of wire harness connector: (to ECM) 0.063,0.021 2.481,0.350 2.418,0.330 10 Front view of wire harness connector: (to Integration Relay) 1.827,0.932 2.115,1.095 0.288,0.163 10 1B 0.366,3.252 0.654,3.415 0.288,0.163 10 A38 2.447,1.803 2.599,1.958 0.153,0.156 10 8 2.268,1.508 2.478,1.777 false 2.429,4.174 3.161,4.330 0.732,0.156 10 28 (IGSW) 2.423,3.227 2.753,4.148 false

a.

Remove the integration relay from the engine room relay block.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1B-8 - A38-28 (IGSW) Always Below 1 Ω
1B-8 or A38-28 (IGSW) - Body ground Always 10 kΩ or higher




OK

7.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - ENGINE ROOM RELAY BLOCK)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - ENGINE ROOM RELAY BLOCK)
U163742E02
2.125,4.073 2.281,4.333 true 1.073,1.656 0.813,2.125 true 0.115,0.073 2.49,0.406 2.375,0.333 10 false Front view of wire harness connector: (to Main Body ECU) 0.135,2.531 2.51,2.865 2.375,0.333 10 false Front view of wire harness connector: (to Integration Relay) 1.854,3.469 2.146,3.635 0.292,0.167 10 false 1B 2.271,4.313 2.406,4.479 0.135,0.167 10 false 6 0.563,2.156 1.104,2.323 0.542,0.167 10 false IG2D 0.385,1.448 0.677,1.615 0.292,0.167 10 false E2

a.

Remove the integration relay from the engine room relay block.


b.

Disconnect the E2 main body ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E2-11 (IG2D) - 1B-6 Always Below 1 Ω
E2-11 (IG2D) or 1B-6 - Body ground Always 10 kΩ or higher




OK

8.CHECK ENTRY AND START SYSTEM (POWER SOURCE MODE DOES NOT CHANGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK ENTRY AND START SYSTEM (POWER SOURCE MODE DOES NOT CHANGE)

OK

NG

REPAIR ENTRY AND START SYSTEM