Home › Engine / Hybrid System › 3UR-FE (ENGINE CONTROL) › SFI SYSTEM(w/o Secondary Air Injection System) › 2014.08–2015.08
RM2660E _51 Engine / Hybrid System _052775 3UR-FE ENGINE CONTROL _0255032 SFI SYSTEM C

3UR-FE ENGINE CONTROL  SFI SYSTEM  P0443  Evaporative Emission Control System Purge Control Valve Circuit  


DESCRIPTION

To reduce HC emissions, evaporated fuel from the fuel tank is routed through a charcoal canister to the intake manifold for combustion in the cylinders.

The ECM changes the duty signals to the purge VSV so that the intake amount of HC emissions is appropriate for driving conditions (engine load, engine speed, vehicle speed, etc.) after the engine is warmed up.

DTC Code DTC Detection Condition Trouble Area
P0443 The terminal voltage of the ECM output circuit does not correspond with the drive signals from the ECM to the purge VSV (1 trip detection logic).
·

Open or short in purge VSV circuit

·

Purge VSV

·

ECM



WIRING DIAGRAM

A221876E08
0.813,2.563 1.365,2.771 0.552,0.208 10 false Battery 1.229,2.052 2.375,2.281 1.146,0.229 10 false Integration Relay 0.854,0.802 1.031,0.99 0.177,0.188 10 false 3 0.802,1 1.052,1.177 0.25,0.177 10 false 1B 0.844,1.458 1.021,1.646 0.177,0.188 10 false 1 0.792,1.635 1.042,1.813 0.25,0.177 10 false 1C 2.594,1.427 2.771,1.615 0.177,0.188 10 false 4 2.531,1.635 2.781,1.813 0.25,0.177 10 false 1B 2.583,0.802 2.76,0.99 0.177,0.188 10 false 2 2.542,1 2.792,1.177 0.25,0.177 10 false 1B 5.323,1.458 5.625,1.646 0.302,0.188 10 false 63 5.292,1.646 5.615,1.823 0.323,0.177 10 false C45 5.313,0.844 5.542,1.031 0.229,0.188 10 false 34 5.292,1.01 5.604,1.188 0.313,0.177 10 false A38 5.646,1 6.167,1.198 0.521,0.198 10 false MREL 5.635,1.531 6.01,1.698 0.375,0.167 10 false PRG 4.094,1.938 4.375,2.104 0.281,0.167 10 false C55 4.104,2.104 4.896,2.302 0.792,0.198 10 false Purge VSV 3.094,1.792 3.75,1.948 0.656,0.156 10 false EFI NO. 2 1.125,1.771 1.771,1.917 0.646,0.146 10 false EFI MAIN 3.146,1.51 3.323,1.698 0.177,0.188 10 false 1 3.531,1.51 3.708,1.698 0.177,0.188 10 false 2 4.052,1.469 4.229,1.656 0.177,0.188 10 false 1 4.781,1.469 4.958,1.656 0.177,0.188 10 false 2 1.917,0.646 2.156,0.792 0.24,0.146 10 false EFI 6.042,2.417 6.417,2.583 0.375,0.167 10 false ECM

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine conditions when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (ACTIVATE THE VSV FOR EVAP CONTROL)
a.
A200511E01
0.55,0.157 1.109,0.306 0.559,0.149 10 VSV ON 2.222,0.157 2.843,0.306 0.621,0.149 10 VSV OFF 0.593,1.471 1.152,1.627 0.559,0.156 10 Air flows 1.985,1.471 3.058,1.627 1.073,0.156 10 Air does not flow

Connect the intelligent tester to the DLC3.


b.

Remove the vacuum hose of the purge VSV from the charcoal canister.


c.

Start the engine and turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the VSV for Evap Control.


e.

When the purge VSV is operated using the tester, check whether the disconnected hose applies suction to your finger.

OK:
Tester Operation Specified Condition
VSV is ON Disconnected hose applies suction to finger
VSV is OFF Disconnected hose applies no suction to finger




NG

2.INSPECT PURGE VSV

OK

2.INSPECT PURGE VSV

OK

3.INSPECT PURGE VSV (POWER SOURCE VOLTAGE)

NG

3.INSPECT PURGE VSV (POWER SOURCE VOLTAGE)
U163203E02
0.219,0.365 2.573,0.771 2.354,0.406 10 false Front view of wire harness connector: (to Purge VSV) 1.542,1.479 1.823,1.656 0.281,0.177 10 false C55

a.

Disconnect the purge VSV connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C55-1 - Body ground Engine switch on (IG) 11 to 14 V




NG

4.CHECK HARNESS AND CONNECTOR (PURGE VSV - INTEGRATION RELAY)

OK

5.CHECK HARNESS AND CONNECTOR (PURGE VSV - ECM)
4.CHECK HARNESS AND CONNECTOR (PURGE VSV - INTEGRATION RELAY)
U163323E01
1.96,3.885 1.717,4.166 false 2.242,4.124 2.456,4.274 0.213,0.150 10 1B 0.489,1.527 0.765,1.676 0.276,0.150 10 C55 1.662,4.164 1.766,4.304 0.104,0.140 10 4 0.063,0.021 2.403,0.370 2.340,0.349 10 Front view of wire harness connector: (to Purge VSV) 0.063,2.467 2.403,2.824 2.340,0.357 10 Front view of wire harness connector: (to Integration Relay)

a.

Disconnect the purge VSV connector.


b.

Remove the integration relay from the engine room relay block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C55-1 - 1B-4 Always Below 1 Ω
C55-1 or 1B-4 - Body ground Always 10 kΩ or higher




OK

REPAIR OR REPLACE POWER SOURCE CIRCUIT

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (PURGE VSV - ECM)
a.

Disconnect the purge VSV connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance between the terminals of the wire harness side connectors.

Standard Resistance:
Tester Connection Condition Specified Condition
C55-2 - C45-63 (PRG) Always Below 1 Ω
C55-2 or C45-63 (PRG) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR