Home › Engine / Hybrid System › 3UR-FE (ENGINE CONTROL) › SFI SYSTEM(w/o Secondary Air Injection System) › 2014.08–2015.08
RM2660E _51 Engine / Hybrid System _052775 3UR-FE ENGINE CONTROL _0255032 SFI SYSTEM C

3UR-FE ENGINE CONTROL  SFI SYSTEM  P0724  Brake Switch "B" Circuit High  


DESCRIPTION

The purpose of this circuit is to prevent the engine from stalling while driving in the lock-up condition when the brakes are suddenly applied.

When the brake pedal is depressed, this switch sends a signal to the ECM. Then the ECM cancels the operation of the lock-up clutch while braking is in progress.

DTC No. DTC Detection Condition Trouble Area
P0724 Stop light switch remains ON even when vehicle is driven in GO (30 km/h (18.63 mph) or more) and STOP (less than 3 km/h (1.86 mph)) pattern 5 times (2 trip detection logic)
·

Short in stop light switch signal circuit

·

Stop light switch

·

ECM



MONITOR DESCRIPTION

This DTC indicates that the stop light switch remains ON. When the stop light switch remains ON during GO and STOP driving, the ECM interprets this as a fault in the stop light switch. Then the MIL illuminates and the ECM stores the DTC. The vehicle must GO (30 km/h (18.63 mph) or more) and STOP (less than 3 km/h (1.86 mph)) 5 times for 2 driving cycles in order for the DTC to be output.

CAUTION / NOTICE / HINT

HINT:

Using the GTS to read the Data List allows switch, sensor, actuator and other item values to be read without removing any parts. Reading the Data List early in troubleshooting is one way to save time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


1.

Warm up the engine.

2.

Turn the engine switch off.

3.

Connect the GTS to the DLC3.

4.

Turn the engine switch to ON.

5.

Turn the GTS on.

6.

Enter the following menus: Powertrain / Engine and ECT / Data List.

7.

Follow the instructions on the GTS and read the Data List.


Item Measurement Item/
Range (Display)
Normal Condition Diagnostic Note
STOP LIGHT SW
(Stop Light Switch)
Stop light switch status/
ON or OFF
·

Brake pedal is depressed: ON

·

Brake pedal is released: OFF


-

PROCEDURE

1.INSPECT STOP LIGHT SWITCH
C171632E18
1.813,1.563 2.188,1.979 true 1.635,1.563 1.219,1.958 true 1.615,1.354 1.229,0.979 true 1.813,1.354 2.177,0.917 true 0.594,3.146 0.854,2.594 0.854,2.594 1.01,2.594 false 0.083,3.792 0.656,4.25 0.573,0.458 9 false Not Pushed 0.823,3.792 1.406,4.135 0.583,0.344 10 false Pushed 1.104,0.865 1.573,1.115 0.469,0.25 10 false 2 2.25,1.927 2.615,2.167 0.365,0.24 10 false 3 0.427,0.115 2.906,0.563 2.479,0.448 10 false Component without harness connected: (Stop Light Switch) 2.24,0.802 2.531,1.073 0.292,0.271 10 false 1 1.083,1.927 1.354,2.156 0.271,0.229 10 false 4 1.083,2.5 1.552,2.75 0.469,0.25 10 false Pin

a.

Remove the stop light switch.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
1 - 2 Pin not pushed Below 1 Ω
Pin pushed 10 kΩ or higher
3 - 4 Pin not pushed 10 kΩ or higher
Pin pushed Below 1 Ω




OK

2.CHECK HARNESS AND CONNECTOR (ECM - BATTERY)

NG

REPLACE STOP LIGHT SWITCH

2.CHECK HARNESS AND CONNECTOR (ECM - BATTERY)
a.
U162915E01
1.879,1.976 2.764,1.619 false 2.804,1.535 3.097,1.739 0.293,0.204 10 STP 0.074,0.062 2.420,0.429 2.346,0.367 10 Front view of wire harness connector: (to ECM) 0.234,1.764 0.508,1.929 0.274,0.166 10 A38

Disconnect the ECM connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A38-36 (STP) - Body ground Brake pedal is depressed 11 to 14 V
A38-36 (STP) - Body ground Brake pedal is released Below 1 V




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR