Home › Engine / Hybrid System › 3UR-FE (ENGINE CONTROL) › SFI SYSTEM(w/o Secondary Air Injection System) › from 2015.08
RM2660E _51 Engine / Hybrid System _052775 3UR-FE ENGINE CONTROL _0255032 SFI SYSTEM(w/o Secondary Air Injection System) C

3UR-FE ENGINE CONTROL  SFI SYSTEM(w/o Secondary Air Injection System)  P0011  Camshaft Position "A" - Timing Over-Advanced or System Performance (Bank 1)  P0012  Camshaft Position "A" - Timing Over-Retarded (Bank 1)  P0021  Camshaft Position "A" - Timing Over-Advanced or System Performance (Bank 2)  P0022  Camshaft Position "A" - Timing Over-Retarded (Bank 2)  


DESCRIPTION

The VVT system includes the ECM, Camshaft Oil Control Valve (OCV) and VVT controller. The ECM sends a target duty-cycle control signal to the OCV. This control signal regulates the oil pressure supplied to the VVT controller. Camshaft timing control is performed according to engine operating conditions such as the intake air volume, throttle valve position and engine coolant temperature. The ECM controls the OCV based on the signals transmitted by several sensors. The VVT controller regulates the intake camshaft angle using oil pressure through the OCV. As a result, the relative positions of the camshaft and crankshaft are optimized, the engine torque and fuel economy improve, and the exhaust emissions decrease under overall driving conditions. The ECM detects the actual intake valve timing using signals from the camshaft and crankshaft position sensors, and performs feedback control. This is how the target intake valve timing is verified by the ECM.

A130637E07
4.655,0.815 6.376,1.027 1.721,0.211 10 VVT Sensor (CMP Sensor) 4.655,1.325 5.481,1.486 0.825,0.161 10 CKP Sensor 0.072,0.015 1.622,0.268 1.550,0.253 12 VVT System: 2.337,1.96 3.613,2.135 1.277,0.174 10 Target Valve Timing 2.337,1.288 3.613,1.462 1.277,0.174 10 Actual Valve Timing 2.687,2.696 3.401,2.870 0.714,0.174 10 Correction 2.826,3.204 3.227,3.379 0.402,0.174 10 ECM 1.602,3.748 3.762,3.922 2.160,0.174 10 Camshaft Oil Control Valve (OCV) 0.17,2.69 0.864,2.865 0.695,0.174 10 Duty-cycle 4.655,1.828 5.494,1.981 0.839,0.154 10 MAF Sensor 4.655,2.854 5.453,3.043 0.797,0.188 10 ECT Sensor 4.655,2.344 5.022,2.512 0.367,0.167 10 TPS 4.655,3.353 5.008,3.507 0.353,0.154 10 VSS 0.317,4.27 1.686,4.474 1.369,0.205 10 Engine Oil Pressure 3.663,4.217 4.889,4.401 1.225,0.184 10 Camshaft Actuator 3.887,4.918 4.988,5.101 1.100,0.184 10 Intake Camshaft 2.566,4.571 2.846,4.275 2.846,4.275 3.611,4.275 false 3.181,4.782 3.323,5.009 3.323,5.009 3.856,5.009 false

DTC Code DTC Detection Condition Trouble Area
P0011
P0021
The intake valve timing is not adjusted in the valve timing advance range (1 trip detection logic).
·

Valve timing

·

Camshaft Oil Control Valve (OCV) (for intake side of Bank 1, 2)

·

OCV filter

·

Camshaft timing gear

·

ECM


P0012
P0022
The intake valve timing is not adjusted in the valve timing retard range (2 trip detection logic).
·

Valve timing

·

OCV (for intake side of Bank 1, 2)

·

OCV filter

·

Camshaft timing gear

·

ECM



MONITOR DESCRIPTION

The ECM optimizes the intake valve timing using the VVT (Variable Valve Timing) system to control the intake camshaft. The VVT system includes the ECM, Camshaft Oil Control Valve (OCV) and VVT controller. The ECM sends a target duty-cycle control signal to the OCV. This control signal regulates the oil pressure supplied to the VVT controller. The VVT controller can advance or retard the intake camshaft.

If the difference between the target and actual intake valve timings is large, and changes in the actual intake valve timing are small, the ECM interprets this as the VVT controller stuck malfunction and stores DTC(s).


Example:

A DTC is stored when the following conditions 1 and 2 are met:

1. It takes 5 seconds or more to change the valve timing by 5°CA.

2. After the above condition 1 is met, the camshaft timing oil control valve is forcibly activated during 10 seconds.


DTC P0011 and P0021 (Advanced Cam Timing) are subject to 1 trip detection logic.

DTC P0012 and P0022 (Retarded Cam Timing) are subject to 2 trip detection logic.

These DTCs indicate that the VVT controller cannot operate properly due to OCV malfunctions or the presence of foreign objects in the OCV.

The monitor will run if all of the following conditions are met:

-

The engine is warm (the engine coolant temperature is 75°C [167°F] or higher).

-

The vehicle has been driven at more than 64 km/h (40 mph) for 3 minutes.

-

The engine has idled for 3 minutes.



CAUTION / NOTICE / HINT

HINT:

DTC P0011, P0012, P0021 or P0022 may be stored when foreign objects in the engine oil are caught in some parts of the system. The DTC will remain stored even if the system returns to normal after a short time. Foreign objects are filtered out by the oil filter.


HINT:
Abnormal Bank Advanced Timing Over
(Valve Timing is Out of Specified Range)
Retarded Timing Over
(Valve Timing is Out of Specified Range)
Bank 1 P0011 P0012
Bank 2 P0021 P0022

·

If DTC P0011 or P0012 is output, check the left bank VVT system for intake side circuit (for Bank 1).

·

Bank 1 refers to the bank that includes the No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from the transmission.

·

If DTC P0021 or P0022 is output, check the right bank VVT system for intake side circuit (for Bank 2).

·

Bank 2 refers to the bank that does not include the No. 1 cylinder.

·

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0011, P0012, P0021 OR P0022)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG) and turn the tester on.


c.

Enter the following menus: Powertrain / Engine and ECT / DTC.


d.

Read DTCs.

Result
Result Proceed to
P0011, P0012, P0021 or P0022 is output A
P0011, P0012, P0021 or P0022 and other DTCs are output B

HINT:

If any DTCs other than P0011, P0012, P0021 or P0022 are output, troubleshoot those DTCs first.




A

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (OPERATE OCV)

B

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (OPERATE OCV)
a.

Connect the intelligent tester to the DLC3.


b.

Start the engine.


c.

Turn the tester on.


d.

Warm up the engine.


e.

Turn the A/C on.


f.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the VVT Linear (Bank 1) or Control the VVT Linear (Bank 2).


g.

Check the engine speed while operating the Camshaft Oil Control Valve (OCV) using the tester.

OK:
Operation Specified Condition
0% Normal engine speed
100% Engine idles roughly or stalls


HINT:

Refer to "Data List / Active Test" [VVT OCV Duty #1, VVT Change Angle #1, VVT OCV Duty #2 and VVT Change Angle #2] (See page Engine / Hybrid System>3UR-FE (ENGINE CONTROL)>SFI SYSTEM(w/o Secondary Air Injection System)>DATA LIST / ACTIVE TEST).




OK

3.CHECK WHETHER DTC OUTPUT RECURS (DTC P0011, P0012, P0021 OR P0022)

NG

4.CHECK VALVE TIMING (CHECK FOR LOOSE AND JUMPED TOOTH OF TIMING CHAIN)
3.CHECK WHETHER DTC OUTPUT RECURS (DTC P0011, P0012, P0021 OR P0022)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG) and turn the tester on.



d.

Start the engine and warm it up.


e.

Switch the ECM from normal mode to check mode using the tester.


f.

Drive the vehicle for more than 10 minutes.


g.

Read DTCs using the tester.

OK:

No DTC output.




OK

NG

4.CHECK VALVE TIMING (CHECK FOR LOOSE AND JUMPED TOOTH OF TIMING CHAIN)
4.CHECK VALVE TIMING (CHECK FOR LOOSE AND JUMPED TOOTH OF TIMING CHAIN)
A166451E07
5.594,0.771 5.479,0.26 false 6.865,0.271 6.729,0.896 false 0.375,0.271 0.573,0.854 false 1.677,0.76 1.823,0.271 false 0.375,0.271 0.667,0.271 false 1.823,0.271 1.51,0.271 false 5.479,0.26 5.75,0.26 false 6.865,0.271 6.594,0.271 false 0.635,3.198 1,4.167 false 1,4.167 1.729,3.156 false 5.458,3.219 6.25,4.24 false 6.25,4.24 6.563,3.281 false 5.792,0.198 6.594,0.375 0.802,0.177 10 false Timing Mark 5.917,4.24 6.771,4.469 0.854,0.229 10 true Timing Mark 0.719,0.188 1.521,0.365 0.802,0.177 10 false Timing Mark 0.635,4.167 2.063,4.479 1.427,0.313 10 true Timing Mark 6.479,2.698 6.792,2.854 0.313,0.156 10 false 18° 5.354,2.729 5.677,2.906 0.323,0.177 10 false 32° 1.667,2.615 1.927,2.813 0.26,0.198 10 false 16° 0.594,2.719 0.844,2.875 0.25,0.156 10 false 2°

a.

Remove the cylinder head cover LH and RH.


b.

Turn the crankshaft pulley, and align its groove with the timing mark "0" of the timing chain cover.


c.

Check that the timing marks of the camshaft timing gears and camshaft timing exhaust gears are at the positions shown in the illustration.

OK:

Timing marks on camshaft timing gears are aligned as shown in the illustration.




OK

5.INSPECT CAMSHAFT OIL CONTROL VALVE ASSEMBLY

NG

5.INSPECT CAMSHAFT OIL CONTROL VALVE ASSEMBLY
A160397E02
0.059,0 2.561,0.350 2.502,0.350 10 Component without harness connected: (Oil Control Valve)

a.

Remove the OCV.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 6.9 to 7.9 Ω



A097066E24
0.24,0.177 1.24,0.385 1,0.208 10 false Valve Moves 2,0.083 2.354,0.24 0.354,0.156 10 false OCV

c.

Check the valve operation.

OK:
Measurement Condition Specified Condition
No battery voltage applied to terminals 1 and 2 → Battery voltage applied to terminals 1 and 2 Valve moves quickly




OK

6.INSPECT OIL CONTROL VALVE FILTER

NG

REPLACE CAMSHAFT OIL CONTROL VALVE ASSEMBLY

6.INSPECT OIL CONTROL VALVE FILTER

b.

Check that the filter is not clogged.

OK:

Filter is not clogged.




OK

7.REPLACE INTAKE CAMSHAFT TIMING GEAR

NG

CLEAN OIL CONTROL VALVE FILTER

7.REPLACE INTAKE CAMSHAFT TIMING GEAR
a.

Replace the intake camshaft timing gear (See page Engine / Hybrid System>3UR-FE (ENGINE MECHANICAL)>ENGINE UNIT>DISASSEMBLY).



NEXT

8.CHECK WHETHER DTC OUTPUT RECURS
8.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG) and turn the tester on.



d.

Start the engine and warm it up.


e.

Switch the ECM from normal mode to check mode using the tester.


f.

Drive the vehicle for more than 10 minutes.


g.

Read the output DTCs using the tester.

OK:

No DTC is output.


HINT:

DTC P0011, P0012, P0021 or P0022 is output when foreign objects in the engine oil are caught in some parts of the system. These codes will stay stored even if the system returns to normal after a short time. These foreign objects are then captured by the oil filter, thus eliminating the source of the problem.




OK

SYSTEM OK

NG