1.INSTALL STUD BOLT
If the stud bolt is deformed or its threads are damaged, replace it.
Install the timing chain cover stud bolt.
Using an E10 "TORX" socket wrench, install the 2 stud bolts as shown in the illustration.
Install the oil pan stud bolt.
Using an E6 and E7 "TORX" socket wrench, install the 3 stud bolts as shown in the illustration.
2.INSTALL RING PIN
It is not necessary to remove the ring pin unless it is being replaced.
Using a plastic-faced hammer, tap in new ring pins to the timing chain cover.
| Item | Ring Pin Diameter | Specified Condition |
|---|---|---|
| Ring pin A | 13 mm (0.512 in.) | 7.5 to 8.5 mm (0.295 to 0.335 in.) |
| Ring pin B | 11 mm (0.433 in.) | 3.6 to 4.6 mm (0.142 to 0.181 in.) |
| *a | 7.5 to 8.5 mm |
| *b | 3.6 to 4.6 mm |
11381A
3.INSTALL REAR CRANKSHAFT OIL SEAL
Using SST, tap in a new oil seal until its surface is flush with the oil seal retainer edge.
0 to 1.0 mm (0 to 0.0394 in.)
Keep the lip free from foreign matter.
Do not tap on the oil seal at an angle.
12109A
4.INSTALL OIL DRAIN PIPE SUB-ASSEMBLY
Apply a light coat of engine oil to a new O-ring.
Install the O-ring to the drain pipe.
Install the oil drain pipe with the bolt.
11381
5.INSTALL ENGINE REAR OIL SEAL RETAINER
Apply seal packing in a continuous line as shown in the illustration.
Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
2.0 to 3.0 mm (0.0787 to 0.118 in.)
3.5 mm (0.138 in.)
| *a | 2.0 to 3.0 mm |
Remove any oil from the contact surface.
Install the oil seal retainer within 3 minutes and tighten the bolts within 15 minutes after applying seal packing.
Install the oil seal retainer with the 6 bolts.
Do not start the engine for at least 2 hours after installing.
When installing the oil seal retainer, make sure the lip of the oil seal is not damaged.
When installing the oil seal retainer, make sure the lip of the oil seal is not folded incorrectly.
15104
6.INSTALL OIL STRAINER SUB-ASSEMBLY
Apply a light coat of engine oil to a new O-ring.
Install the O-ring to the oil strainer.
Install the oil strainer with the 2 bolts.
Make sure the O-ring is not twisted or damaged.
12121
7.INSTALL NO. 1 OIL PAN BAFFLE PLATE
Install the baffle plate with the 7 bolts.
12101
8.INSTALL NO. 1 OIL PAN SUB-ASSEMBLY
Apply seal packing in a continuous line as shown in the illustration.
Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
3.0 to 4.0 mm (0.118 to 0.157 in.)
| *a | 3.0 to 4.0 mm |
Remove any oil from the contact surface.
Install the oil pan within 3 minutes and tighten the bolts and nuts within 15 minutes after applying seal packing.
Install the oil pan with the 14 bolts and 2 nuts.
|
Bolt |
|
Nut |
Do not start the engine for at least 2 hours after installing.
| Item | Length | Thread Diameter |
|---|---|---|
| Bolt A | 92 mm (3.62 in.) | 6 mm (0.236 in.) |
| Bolt B | 30 mm (1.18 in.) | 10 mm (0.394 in.) |
12102A
9.INSTALL NO. 2 OIL PAN SUB-ASSEMBLY
Apply seal packing in a continuous line as shown in the illustration.
Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
3.0 to 4.0 mm (0.118 to 0.157 in.)
| *a | 3.0 to 4.0 mm |
Remove any oil from the contact surface.
Install the oil pan within 3 minutes and tighten the bolts and nuts within 15 minutes after applying seal packing.
Install the oil pan with the 14 bolts and 2 nuts.
|
Bolt |
|
Nut |
Do not start the engine for at least 2 hours after installing.
16877
10.INSTALL NO. 1 HEAT EXCHANGER COVER
Apply seal packing in a continuous line as shown in the illustration.
Toyota Genuine Seal Packing 1282B, Three Bond 1282B or equivalent
3.0 to 4.0 mm (0.118 to 0.157 in.)
| *a | 3.0 to 4.0 mm |
Remove any oil from the contact surface.
Install the heat exchanger cover within 3 minutes and tighten the bolts and nuts within 15 minutes after applying seal packing.
Install the heat exchanger cover with the 12 bolts and 2 nuts.
|
Bolt |
|
Nut |
Do not start the engine for at least 2 hours after installing.
| Item | Length | Thread Diameter |
|---|---|---|
| Bolt A | 20 mm (0.787 in.) | 8 mm (0.315 in.) |
| Bolt B | 70 mm (2.76 in.) | 8 mm (0.315 in.) |
| Bolt C | 16 mm (0.630 in.) | 6 mm (0.236 in.) |
12203A
11.INSTALL VENTILATION PIPE GASKET
Using SST, evenly tap in a new ventilation pipe gasket until its surface is flush with the lip of the ventilation pipe.
Do not tap the gasket at an angle.
Do not tap the gasket excessively.
11445
12.INSTALL CYLINDER BLOCK WATER JACKET SPACER
Install the 2 water jacket spacers as shown in the illustration.
| *a | UP Mark |
Face the cutouts indicated by the arrows in illustration away from the engine.
Face the "UP" mark as shown in the illustration.
11101
13.INSTALL CYLINDER HEAD SUB-ASSEMBLY RH
11102
14.INSTALL CYLINDER HEAD SUB-ASSEMBLY LH
13716
15.INSTALL VALVE STEM CAP
Apply a light coat of engine oil to the valve stem caps.
Install the 32 valve stem caps to the cylinder heads.
13750
16.INSTALL VALVE LASH ADJUSTER ASSEMBLY
Inspect the valve lash adjuster before installing it (See page Engine / Hybrid System>3UR-FE (ENGINE MECHANICAL)>ENGINE UNIT>INSPECTION).
Install the 32 valve lash adjusters to the cylinder heads.
Install the lash adjuster to the same place it was removed from.
13801
17.INSTALL NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY
Apply engine oil to the lash adjuster tips and valve stem cap ends.
Install the 32 valve rocker arms as shown in the illustration.
| *1 | Valve Rocker Arm |
| *2 | Valve Stem Cap |
| *3 | Valve Lash Adjuster |
18.INSTALL CAMSHAFT BEARING CAP RH
11103C
19.INSTALL CAMSHAFT HOUSING SUB-ASSEMBLY RH
20.INSTALL CAMSHAFT BEARING CAP LH
11104A
21.INSTALL CAMSHAFT HOUSING SUB-ASSEMBLY LH
13521A
22.INSTALL CRANKSHAFT TIMING GEAR KEY
Install the timing gear key.
The other timing gear key will be installed at a later step.
23.SET NO. 1 CYLINDER TO TDC/COMPRESSION
Temporarily install the crankshaft pulley bolt.
Rotate the crankshaft so that the timing gear key is as shown in the illustration. Then using a wrench, rotate each camshaft so that the timing marks are as shown in the illustration.
When the crankshaft or a camshaft is rotated excessively, the valves and pistons may interfere with each other.
Remove the crankshaft pulley bolt.
| *1 | IN | *2 | EX |
| *3 | Knock Pin | *4 | Key |
| *a | Toward Ceiling | - | - |
13550
24.INSTALL NO. 2 CHAIN TENSIONER ASSEMBLY
Install the chain tensioner with the 2 bolts.
| *1 | Plunger |
| *2 | Pin |
| *a | Push |
While raising up the No. 2 chain tensioner, insert a pin of 1.0 mm (0.0394 in.) into the hole to fix it in place.
13506
25.INSTALL NO. 1 CHAIN SUB-ASSEMBLY RH
Align the No. 1 chain orange mark plate with the camshaft timing gear timing mark, and attach the chain to the gear as shown in the illustration.
| *1 | Mark Plate |
| *2 | Timing Mark |
Align the No. 1 chain orange mark plate with the crankshaft timing sprocket timing mark, and attach the chain to the gear as shown in the illustration.
| *1 | Mark Plate |
| *2 | Timing Mark |
Align the No. 2 chain yellow mark plates with the timing marks of the camshaft timing gear assembly and camshaft timing exhaust gear assembly, and attach the No. 2 chain to the gears as shown in the illustration.
| *1 | Mark Plate |
| *2 | Timing Mark |
The camshaft timing exhaust gear has 2 grooves. Align the mark plates of the No. 2 chain with the first groove.
The crankshaft timing sprocket RH and camshaft timing exhaust gear will be installed with the No. 1 and No. 2 chains connected to the gears.
Install the crankshaft timing sprocket RH to the crankshaft.
Align and attach the knock pin of the No. 1 camshaft with the pin hole of the camshaft timing gear.
Using the hexagonal portion of the No. 2 camshaft, align and attach the knock pin of the No. 2 camshaft with the pin hole of the camshaft timing exhaust gear.
Remove the pin from the No. 2 chain tensioner.
Using a wrench to hold the hexagonal portion of the No. 1 camshaft, temporarily install the bolt.
Using a wrench to hold the hexagonal portion of the No. 2 camshaft, temporarily install the bolt.
13561
26.INSTALL NO. 1 CHAIN VIBRATION DAMPER RH
Install the vibration damper with the 2 bolts.
13559
27.INSTALL NO. 1 CHAIN TENSIONER SLIPPER RH
If you cannot install the chain tensioner slipper due to the tension of the chain, use the hexagonal portion of the camshaft to loosen the chain, and then install the chain tensioner slipper.
13540
28.INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY RH
Move the stopper plate clockwise to release the lock, and push the plunger deep into the tensioner.
| *1 | Stopper Plate |
| *2 | Plunger |
Move the stopper plate counterclockwise to set the lock, and insert a hexagon wrench into the hole of the stopper plate.
Install the chain tensioner with the 2 bolts.
Remove the hexagon wrench from the chain tensioner.
13560A
29.INSTALL NO. 3 CHAIN TENSIONER ASSEMBLY
Install the chain tensioner with the 2 bolts.
| *1 | Plunger |
| *2 | Pin |
| *a | Push |
While pushing down the No. 2 chain tensioner, insert a pin of 1.0 mm (0.0394 in.) into the hole to fix it in place.
13506
30.INSTALL NO. 1 CHAIN SUB-ASSEMBLY LH
Align the No. 1 chain orange mark plate with the camshaft timing gear timing mark, and attach the chain to the gear as shown in the illustration.
| *1 | Mark Plate |
| *2 | Timing Mark |
Align the No. 1 chain orange mark plate with the crankshaft timing sprocket timing mark, and attach the chain to the gear as shown in the illustration.
| *1 | Mark Plate |
| *2 | Timing Mark |
Align the No. 2 chain yellow mark plates with the timing marks of the camshaft timing gear assembly and camshaft timing exhaust gear assembly, and attach the No. 2 chain to the gears as shown in the illustration.
| *1 | Mark Plate |
| *2 | Timing Mark |
The camshaft timing exhaust gear has 2 grooves. Align the mark plates of the No. 2 chain with the first groove.
The crankshaft timing sprocket LH and camshaft timing exhaust gear will be installed with the No. 1 and No. 2 chains connected to the gears.
Install the crankshaft timing sprocket LH to the crankshaft.
Align and attach the knock pin of the No. 3 camshaft with the pin hole of the camshaft timing gear.
Using the hexagonal portion of the No. 4 camshaft, align and attach the knock pin of the No. 4 camshaft with the pin hole of the camshaft timing exhaust gear.
Because the timing mark positions of the gears may shift due to looseness of the No. 1 chain, use the hexagonal portion of the camshaft to hold the No. 3 camshaft in place until the No. 1 chain tensioner is installed.
Remove the pin from the No. 3 chain tensioner.
Using a wrench to hold the hexagonal portion of the No. 3 camshaft, temporarily install the bolt.
Using a wrench to hold the hexagonal portion of the No. 4 camshaft, temporarily install the bolt.
13559
31.INSTALL NO. 1 CHAIN TENSIONER SLIPPER LH
If you cannot install the chain tensioner slipper due to the tension of the chain, use the hexagonal portion of the camshaft to loosen the chain, and install the chain tensioner slipper.
13540
32.INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY LH
Move the stopper plate clockwise to release the lock, and push the plunger deep into the tensioner.
| *1 | Stopper Plate |
| *2 | Plunger |
Move the stopper plate counterclockwise to set the lock, and insert a hexagon wrench into the hole of the stopper plate.
Install a new gasket and the chain tensioner with the 2 bolts.
13561
33.INSTALL NO. 1 CHAIN VIBRATION DAMPER LH
Install the vibration damper with the 2 bolts.
Remove the hexagon wrench from the No. 1 chain tensioner.
13050
34.TIGHTEN CAMSHAFT TIMING GEAR
for Bank 1:
Using a wrench, hold the hexagonal portion of the No. 3 camshaft.
| *a | Hold |
|
Turn |
Tighten the bolt of the camshaft timing gear.
Using a wrench to hold the hexagonal portion of the No. 4 camshaft, tighten the bolt of the camshaft timing exhaust gear.
| *a | Hold |
|
Turn |
for Bank 2:
Using a wrench, hold the hexagonal portion of the No. 1 camshaft.
| *a | Hold |
|
Turn |
Tighten the bolt of the camshaft timing gear.
Using a wrench to hold the hexagonal portion of the No. 2 camshaft, tighten the bolt of the camshaft timing exhaust gear.
| *a | Hold |
|
Turn |
35.CHECK NO. 1 CYLINDER TO TDC/COMPRESSION
Temporarily install the crankshaft pulley bolt.
Rotate the crankshaft clockwise, and check that the timing marks on the crankshaft timing sprocket and camshaft timing gears are as shown in the illustration.
Remove the crankshaft pulley bolt.
| *1 | Timing Mark | *2 | Timing Mark Position |
| *3 | Knock Pin Position | *4 | Key |
| *a | Toward Ceiling | *b | Approximately 2° |
| *c | Approximately 45° | *d | Approximately 16° |
| *e | Approximately 18° | *f | Approximately 32° |
16322
36.INSTALL WATER INLET PIPE
11302
37.INSTALL TIMING CHAIN COVER SUB-ASSEMBLY
16100
38.INSTALL WATER PUMP ASSEMBLY
11301C
39.INSTALL FRONT CRANKSHAFT OIL SEAL
13521A
40.INSTALL CRANKSHAFT TIMING GEAR KEY
13471
41.INSTALL CRANKSHAFT PULLEY
11193
42.INSTALL SPARK PLUG TUBE GASKET
Using a cutter knife, cut off the seal part of the removed gasket.
|
Area to cut off |
Using the removed gasket and a hammer, tap in a new gasket until it stops.
| *1 | Removed Gasket |
| *2 | New Gasket |
If the removed gasket does not fit on the new one, correct the removed one with pliers.
Apply a light coat of MP grease to the lip of the gasket.
Return the 4 ventilation baffle plate claws to the original positions.
15678A
43.INSTALL OIL CONTROL VALVE FILTER
LH:
Install the filter in the cylinder head.
| *1 | Cylinder Head Cover Spacer |
| *2 | Gasket |
| *3 | Filter |
Install a new gasket and the cylinder head cover spacer with the 3 bolts.
RH:
Install the filter in the cylinder head.
| *1 | Cylinder Head Cover Spacer |
| *2 | Gasket |
| *3 | Filter |
Install a new gasket and the cylinder head cover spacer with the 3 bolts.
11201
44.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY RH
11202
45.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY LH
16603
46.INSTALL NO. 1 IDLER PULLEY SUB-ASSEMBLY
16173
47.INSTALL WATER PUMP PULLEY
15330B
48.INSTALL CAMSHAFT OIL CONTROL VALVE ASSEMBLY
for Bank 1:
Apply a light coat of engine oil to 2 new O-rings.
Install the 2 O-rings to the 2 oil control valves.
Install the 2 oil control valves with the 2 bolts.
for Bank 2:
Apply a light coat of engine oil to 2 new O-rings.
Install the 2 O-rings to the 2 oil control valves.
Install the 2 oil control valves with the 2 bolts.
89491
49.INSTALL ENGINE OIL LEVEL SENSOR
11401G
50.INSTALL CRANKSHAFT POSITION SENSOR
Install the crankshaft position sensor with the bolt.
19312
51.INSTALL CRANK POSITION SENSOR PROTECTOR
Install the sensor protector with the 2 bolts.
11102A
52.INSTALL CAMSHAFT POSITION SENSOR
Install the camshaft position sensor with the bolt.
53.INSTALL VVT SENSOR
for Bank 1:
Install the 2 VVT sensors with the 2 bolts.
for Bank 2:
Install the 2 VVT sensors with the 2 bolts.
19100P
54.INSTALL SPARK PLUG
Using a 16 mm plug wrench, install the 8 spark plugs.
12185
55.INSTALL OIL FILLER CAP HOUSING
Align the protrusion of a new gasket with the cutout of the oil filler cap housing, and install the gasket to the housing.
Install the cap housing with the 2 bolts.
12108
56.INSTALL OIL FILLER CAP SUB-ASSEMBLY
15671
57.INSTALL OIL FILTER BRACKET
15781
58.INSTALL NO. 1 OIL COOLER BRACKET
59.INSTALL OIL FILTER ELEMENT
83520
60.INSTALL OIL PRESSURE SENDER GAUGE ASSEMBLY