83520
1.REMOVE OIL PRESSURE SENDER GAUGE ASSEMBLY
2.REMOVE OIL FILTER ELEMENT
15781
3.REMOVE NO. 1 OIL COOLER BRACKET
15671
4.REMOVE OIL FILTER BRACKET
12108
5.REMOVE OIL FILLER CAP SUB-ASSEMBLY
12185
6.REMOVE OIL FILLER CAP HOUSING
Remove the 2 bolts, filler cap housing and gasket.
19100P
7.REMOVE SPARK PLUG
Using a 16 mm plug wrench, remove the 8 spark plugs.
8.REMOVE VVT SENSOR
LH:
Remove the 2 bolts and 2 VVT sensors.
RH:
Remove the 2 bolts and 2 VVT sensors.
11102A
9.REMOVE CAMSHAFT POSITION SENSOR
Remove the bolt and camshaft position sensor.
19312
10.REMOVE CRANK POSITION SENSOR PROTECTOR
Remove the 2 bolts and sensor protector.
11401G
11.REMOVE CRANKSHAFT POSITION SENSOR
Remove the bolt and crankshaft position sensor.
89491
12.REMOVE ENGINE OIL LEVEL SENSOR
15330B
13.REMOVE CAMSHAFT OIL CONTROL VALVE ASSEMBLY
LH:
Remove the 2 bolts and 2 oil control valves.
RH:
Remove the 2 bolts and 2 oil control valves.
16173
14.REMOVE WATER PUMP PULLEY
16603
15.REMOVE NO. 1 IDLER PULLEY SUB-ASSEMBLY
16211
16.REMOVE FLUID COUPLING BRACKET
16620
17.REMOVE V-RIBBED BELT TENSIONER ASSEMBLY
11202
18.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY LH
11201
19.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY RH
15678A
20.REMOVE OIL CONTROL VALVE FILTER
LH:
Remove the 3 bolts, cylinder head cover spacer, gasket and filter.
| *1 | Cylinder Head Cover Spacer |
| *2 | Gasket |
| *3 | Filter |
RH:
Remove the 3 bolts, cylinder head cover spacer, gasket and filter.
| *1 | Cylinder Head Cover Spacer |
| *2 | Gasket |
| *3 | Filter |
11193
21.REMOVE SPARK PLUG TUBE GASKET
Bend the 4 ventilation baffle plate claws on the cylinder head cover to an angle of 90° or more.
Using a screwdriver, pry out the gaskets.
| *1 | Tape |
|
Pry |
Be careful not to damage the cylinder head cover.
Be careful not to damage the gasket when removing it, as the removed gasket needs to be used when installing a new one.
Tape the screwdriver tip before use.
13471
22.REMOVE CRANKSHAFT PULLEY
16100
23.REMOVE WATER PUMP ASSEMBLY
11302
24.REMOVE TIMING CHAIN COVER SUB-ASSEMBLY
16322
25.REMOVE WATER INLET PIPE
11301C
26.REMOVE FRONT CRANKSHAFT OIL SEAL
Place the timing chain cover on wooden blocks.
Using a screwdriver and wooden block, pry out the oil seal.
| *1 | Wooden Block |
Do not damage the surface of the oil seal press fit hole.
Tape the screwdriver tip before use.
27.SET NO. 1 CYLINDER TO TDC/COMPRESSION
Temporarily install the crankshaft pulley bolt.
Rotate the crankshaft clockwise so that the timing marks on the crankshaft timing sprocket and camshaft timing gears are as shown in the illustration.
If the timing marks do not align, rotate the crankshaft clockwise again and align the timing marks.
| *1 | Timing Mark | *2 | Timing Mark Position |
| *3 | Knock Pin Position | *4 | Key |
| *a | Toward Ceiling | *b | Approximately 2° |
| *c | Approximately 45° | *d | Approximately 16° |
| *e | Approximately 18° | *f | Approximately 32° |
13540
28.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY LH
Move the stopper plate clockwise to release the lock, and push the plunger deep into the tensioner.
| *1 | Plunger |
| *2 | Stopper Plate |
Move the stopper plate counterclockwise to set the lock, and insert a hexagon wrench into the stopper plate hole.
| *1 | Plunger |
| *2 | Stopper Plate |
Remove the 2 bolts, chain tensioner and gasket.
13559
29.REMOVE NO. 1 CHAIN TENSIONER SLIPPER LH
13561
30.REMOVE NO. 1 CHAIN VIBRATION DAMPER LH
Remove the 2 bolts and chain vibration damper.
13506
31.REMOVE NO. 1 CHAIN SUB-ASSEMBLY LH
While pushing down the No. 3 chain tensioner, insert a pin of 1.0 mm (0.0394 in.) into the hole to fix it in place.
| *1 | Pin |
| *2 | Plunger |
| *a | Push |
Hold the hexagonal portion of the camshaft with a wrench and loosen the bolt.
| *a | Hold |
|
Turn |
Be careful not to damage the cylinder head with the wrench.
Do not disassemble the camshaft timing gear.
Hold the hexagonal portion of the camshaft with a wrench and loosen the bolt.
| *a | Hold |
|
Turn |
Be careful not to damage the cylinder head with the wrench.
Remove the 2 bolts. Then with the No. 1 and No. 2 chains still connected to the gears, remove the camshaft timing gear, camshaft timing exhaust gear and crankshaft timing sprocket LH.
Remove the No. 1 and No. 2 chains from the gears.
13560A
32.REMOVE NO. 3 CHAIN TENSIONER ASSEMBLY
Remove the 2 bolts and chain tensioner.
13540
33.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY RH
Move the stopper plate clockwise to release the lock, and push the plunger deep into the tensioner.
| *1 | Plunger |
| *2 | Stopper Plate |
Move the stopper plate counterclockwise to set the lock, and insert a hexagon wrench into the stopper plate hole.
| *1 | Plunger |
| *2 | Stopper Plate |
Remove the 2 bolts and chain tensioner.
13559
34.REMOVE NO. 1 CHAIN TENSIONER SLIPPER RH
13561
35.REMOVE NO. 1 CHAIN VIBRATION DAMPER RH
Remove the 2 bolts and vibration damper.
13506
36.REMOVE NO. 1 CHAIN SUB-ASSEMBLY RH
While raising up the No. 2 chain tensioner, insert a pin of 1.0 mm (0.0394 in.) into the hole to fix it in place.
| *1 | Pin |
| *2 | Plunger |
| *a | Push |
Hold the hexagonal portion of the camshaft with a wrench and loosen the bolt.
| *a | Hold |
|
Turn |
Be careful not to damage the cylinder head with the wrench.
Do not disassemble the camshaft timing gear.
Hold the hexagonal portion of the camshaft with a wrench and loosen the bolt.
| *a | Hold |
|
Turn |
Be careful not to damage the cylinder head with the wrench.
Remove the 2 bolts. Then with the No. 1 and No. 2 chains still connected to the gears, remove the camshaft timing gear, camshaft timing exhaust gear and crankshaft timing sprocket RH.
Remove the No. 1 and No. 2 chains from the gears.
13550
37.REMOVE NO. 2 CHAIN TENSIONER ASSEMBLY
Remove the 2 bolts and chain tensioner.
13521A
38.REMOVE CRANKSHAFT TIMING GEAR KEY
Using a screwdriver, remove the 2 timing gear keys from the crankshaft.
39.REMOVE CAMSHAFT BEARING CAP LH
11104A
40.REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY LH
41.REMOVE CAMSHAFT BEARING CAP RH
11103C
42.REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY RH
13801
43.REMOVE NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY
Remove the 32 valve rocker arms from the cylinder heads.
Arrange the removed parts in the correct order.
13750
44.REMOVE VALVE LASH ADJUSTER ASSEMBLY
Remove the 32 valve lash adjusters from the cylinder heads.
Arrange the removed parts in the correct order.
13716
45.REMOVE VALVE STEM CAP
Remove the 32 valve stem caps from the cylinder heads.
Arrange the removed parts in the correct order.
11102
46.REMOVE CYLINDER HEAD SUB-ASSEMBLY LH
11101
47.REMOVE CYLINDER HEAD SUB-ASSEMBLY RH
11445
48.REMOVE CYLINDER BLOCK WATER JACKET SPACER
Remove the 2 water jacket spacers from the cylinder block.
Be sure to remove the water jacket spacers. If not, they may fall and become damaged when the cylinder block is inverted.
12203A
49.REMOVE VENTILATION PIPE GASKET
Using a screwdriver, pry out the ventilation pipe gasket.
Tape the screwdriver tip before use.
16877
50.REMOVE NO. 1 HEAT EXCHANGER COVER
Remove the 12 bolts and 2 nuts.
|
Bolt |
|
Nut |
Remove the heat exchanger by prying between the heat exchanger and cylinder block with a screwdriver.
Tape the screwdriver tip before use.
12102A
51.REMOVE NO. 2 OIL PAN SUB-ASSEMBLY
Remove the 14 bolts and 2 nuts.
|
Bolt |
|
Nut |
Insert the blade of an oil pan seal cutter between the oil pans. Cut through the applied sealer and remove the No. 2 oil pan.
Be careful not to damage the contact surfaces of the oil pans.
12101
52.REMOVE NO. 1 OIL PAN SUB-ASSEMBLY
Remove the 14 bolts and 2 nuts.
|
Bolt |
|
Nut |
Be sure to clean the bolts and stud bolts, and check the threads for cracks or other damage.
Remove the oil pan by prying between the oil pan and cylinder block with a screwdriver.
| *A | LH Side |
| *B | RH Side |
Be careful not to damage the contact surfaces of the cylinder block and oil pan.
Tape the screwdriver tip before use.
12121
53.REMOVE NO. 1 OIL PAN BAFFLE PLATE
Remove the 7 bolts and baffle plate.
15104
54.REMOVE OIL STRAINER SUB-ASSEMBLY
Remove the 2 bolts, oil strainer and O-ring.
11381
55.REMOVE ENGINE REAR OIL SEAL RETAINER
Remove the 6 bolts and oil seal retainer.
Using a screwdriver, pry out the oil seal retainer.
Tape the screwdriver tip before use.
12109A
56.REMOVE OIL DRAIN PIPE SUB-ASSEMBLY
Remove the bolt and oil drain pipe.
Remove the O-ring.
11381A
57.REMOVE REAR CRANKSHAFT OIL SEAL
Place the oil seal retainer on wooden blocks.
| *1 | Wooden Block |
Using a screwdriver and hammer, tap out the oil seal.
58.REMOVE RING PIN
It is not necessary to remove the ring pin unless it is being replaced.
59.REMOVE STUD BOLT
If the stud bolt is deformed or its threads are damaged, replace it.