Home › Engine / Hybrid System › 3UR-FE (ENGINE CONTROL) › SFI SYSTEM(w/o Secondary Air Injection System) › 2014.08–2015.08
RM2660E _51 Engine / Hybrid System _052775 3UR-FE ENGINE CONTROL _0255032 SFI SYSTEM C

3UR-FE ENGINE CONTROL  SFI SYSTEM  P0037  Oxygen Sensor Heater Control Circuit Low (Bank 1 Sensor 2)  P0038  Oxygen Sensor Heater Control Circuit High (Bank 1 Sensor 2)  P0057  Oxygen Sensor Heater Control Circuit Low (Bank 2 Sensor 2)  P0058  Oxygen Sensor Heater Control Circuit High (Bank 2 Sensor 2)  P102D  O2 Sensor Heater Circuit Performance Bank 1 Sensor 2 Stuck ON  P105D  O2 Sensor Heater Circuit Performance Bank 2 Sensor 2 Stuck ON  


DESCRIPTION


HINT:
·

When any of these DTCs is stored, the ECM enters fail-safe mode. The ECM turns off the Heated Oxygen (HO2) Sensor heater in fail-safe mode. Fail-safe mode continues until the engine switch is turned off.

·

The ECM provides a pulse width modulated control circuit to adjust the current through the heater. The HO2 sensor heater circuit uses a relay on the +B side of the circuit.

A164717E02
0.039,0.007 2.909,0.307 2.869,0.300 12 Reference (System Diagram): 2.829,1.184 3.509,1.365 0.680,0.181 10 EFI NO. 2 2.292,2.646 2.560,2.827 0.269,0.181 10 EFI 1.088,1.198 1.741,1.379 0.653,0.181 10 EFI MAIN 1.02,3.33 1.500,3.512 0.480,0.181 10 Ground 3.751,2.121 4.585,2.302 0.834,0.181 10 HO2 Sensor 3.557,0.937 3.782,1.118 0.226,0.181 10 +B 4.368,0.937 4.748,1.118 0.380,0.181 10 HT1B 3.564,1.5 3.821,1.681 0.258,0.181 10 E1 4.362,1.5 4.786,1.681 0.424,0.181 10 OX1B 5.376,1.48 5.800,1.661 0.424,0.181 10 OX1B 5.396,2.269 5.820,2.450 0.424,0.181 10 EX1B 3.958,1.184 4.394,1.365 0.436,0.181 10 Heater 3.916,1.792 4.375,1.973 0.459,0.181 10 Sensor 6.209,3.416 6.535,3.598 0.326,0.181 10 ECM 5.369,0.949 5.749,1.131 0.380,0.181 10 HT1B 5.389,2.852 5.792,3.033 0.403,0.181 10 MREL 0.485,1.002 0.977,1.363 0.492,0.360 10 from Battery



DTC Code DTC Detection Condition Trouble Area
P0037
P0057
The Heated Oxygen (HO2) sensor heater current is below 0.3 A
(1 trip detection logic)
·

Open in Heated Oxygen (HO2) sensor heater circuit

·

HO2 sensor heater (for Sensor 2)

·

Integration relay

·

ECM


P0038
P0058
The Heated Oxygen (HO2) sensor heater current is higher than 2 A
(1 trip detection logic)
·

Short in HO2 sensor heater circuit

·

HO2 sensor heater (for Sensor 2)

·

Integration relay

·

ECM


P102D
P105D
The heater current is higher than the specified value while the heater is not operating.
(1 trip detection logic)
ECM

MONITOR DESCRIPTION

The sensing portion of the Heated Oxygen (HO2) sensor has a zirconia element which is used to detect the oxygen concentration in the exhaust gas. If the zirconia element is at the appropriate temperature, and the difference between the oxygen concentrations surrounding the inside and outside surfaces of the sensor is large, the zirconia element generates voltage signals. In order to increase the oxygen concentration detecting capacity of the zirconia element, the ECM supplements the heat from the exhaust with heat from a heating element inside the sensor.

Heated oxygen sensor heater range check (P0037, P0038, P0057, P0058, P102D and P105D):

The ECM monitors the current applied to the heated oxygen sensor heater to check the heater for malfunctions.

If the heater current is outside the normal range, the signal transmitted by the heated oxygen sensor becomes inaccurate. When the current in the heated oxygen sensor heater is outside the normal operating range, the ECM interprets this as a malfunction in the sensor heater and stores a DTC.


CONFIRMATION DRIVING PATTERN

These DTCs are stored when the engine idles for 110 seconds or more.

CAUTION / NOTICE / HINT

HINT:
·

Sensor 2 refers to the sensor mounted behind the Three-Way Catalytic Converter (TWC) and located far from the engine assembly.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

Bank 1 refers to the bank that includes the No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from the transmission.

·

Bank 2 refers to the bank that does not include the No. 1 cylinder.

·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.



PROCEDURE

1.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE)
A385674E01
1.365,1.26 0.865,1.167 true 1.323,1.75 0.875,1.917 true 2.531,1.156 1.99,1.281 true 2.563,1.917 2.031,1.781 true 1.406,3.698 0.906,3.604 true 1.406,4.229 0.958,4.396 true 2.427,3.594 1.958,3.708 true 2.448,4.396 1.927,4.219 true 0.073,0.042 2.531,0.542 2.458,0.5 10 false Component without harness connected (HO2 Sensor for Bank 1) 0.094,2.24 2.552,2.74 2.458,0.5 10 false Component without harness connected (HO2 Sensor for Bank 2) 0.646,1.073 0.906,1.292 0.26,0.219 10 false +B 0.677,1.854 0.938,2.073 0.26,0.219 10 false E1 2.583,1.083 3.063,1.333 0.479,0.25 10 false HT1B 2.615,1.875 3.094,2.125 0.479,0.25 10 false OX1B 0.698,3.51 0.958,3.729 0.26,0.219 10 false +B 0.74,4.344 1,4.563 0.26,0.219 10 false E1 2.5,3.49 2.979,3.74 0.479,0.25 10 false HT2B 2.49,4.344 2.969,4.594 0.479,0.25 10 false OX2B

a.

Disconnect the C20 or C56 heated oxygen (HO2) sensor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (HT1B) - 2 (+B) 20°C (68°F) 11 to 16 Ω
1 (HT1B) - 4 (E1) Always 10 kΩ or higher
1 (HT2B) - 2 (+B) 20°C (68°F) 11 to 16 Ω
1 (HT2B) - 4 (E1) Always 10 kΩ or higher




OK

2.CHECK TERMINAL VOLTAGE (+B OF HO2 SENSOR)

NG

2.CHECK TERMINAL VOLTAGE (+B OF HO2 SENSOR)
A385675E01
2.042,1.156 2.75,0.948 true 1.969,3.719 2.677,3.51 true 0.188,0.01 2.583,0.552 2.396,0.542 10 false Front view of wire harness connector: (to HO2 Sensor for Bank 1) 0.542,1.26 0.958,1.427 0.417,0.167 10 false C20 0.552,3.823 0.969,3.99 0.417,0.167 10 false C56 0.25,2.25 2.646,2.792 2.396,0.542 10 false Front view of wire harness connector: (to HO2 Sensor for Bank 2) 2.823,0.844 3.24,1.01 0.417,0.167 10 false +B 2.719,3.438 3.135,3.604 0.417,0.167 10 false +B

a.

Disconnect the C20 or C56 HO2 sensor connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C20-2 (+B) - Body ground Engine switch on (IG) 11 to 14 V
C56-2 (+B) - Body ground Engine switch on (IG) 11 to 14 V


Result
Result Proceed to
NG A
OK B



A

3.INSPECT INTEGRATION RELAY (EFI)

B

5.CHECK HARNESS AND CONNECTOR (HO2 SENSOR - ECM)
3.INSPECT INTEGRATION RELAY (EFI)
a.

Remove the integration relay from the engine room relay block.


b.

Inspect the EFI MAIN fuse.

i.

Remove the EFI MAIN fuse from the integration relay.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
EFI MAIN fuse Always Below 1 Ω



iii.

Reinstall the EFI MAIN fuse.



U151425E03
0.073,0.063 2.583,0.427 2.51,0.365 10 false Component without harness connected: (Integration Relay) 0.49,2.417 0.719,2.563 0.229,0.146 10 false 1C 1.344,2.417 1.531,2.563 0.188,0.146 10 false 1B 2.448,2.417 2.635,2.563 0.188,0.146 10 false 1A

c.

Inspect the EFI relay.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1C-1 - 1B-4 No battery voltage applied to terminals 1B-2 and 1B-3 10 kΩ or higher
Battery voltage applied to terminals 1B-2 and 1B-3 Below 1 Ω





OK

4.CHECK HARNESS AND CONNECTOR (HO2 SENSOR - INTEGRATION RELAY)

NG

REPLACE INTEGRATION RELAY (EFI)

4.CHECK HARNESS AND CONNECTOR (HO2 SENSOR - INTEGRATION RELAY)
a.

Check the EFI NO. 2 fuse.

i.

Remove the EFI NO. 2 fuse from the engine room relay block.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
EFI NO. 2 fuse Always Below 1 Ω



iii.

Reinstall the EFI NO. 2 fuse.



b.

Disconnect the C20 or C56 HO2 sensor connector.


c.

Remove the integration relay from the engine room relay block.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C20-2 (+B) - 1B-4 Always Below 1 Ω
C56-2 (+B) - 1B-4 Always Below 1 Ω
C20-2 (+B) or 1B-4 - Body ground Always 10 kΩ or higher
C56-2 (+B) or 1B-4 - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (HO2 SENSOR - ECM)
a.

Disconnect the C20 or C56 HO2 sensor connector.


b.

Disconnect the C45 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C20-1 (HT1B) - C45-45 (HT1B) Always Below 1 Ω
C56-1 (HT2B) - C45-44 (HT2B) Always Below 1 Ω
C20-1 (HT1B) or C45-45 (HT1B) - Body ground Always 10 kΩ or higher
C56-1 (HT2B) or C45-44 (HT2B) - Body ground Always 10 kΩ or higher




OK

6.CHECK WHETHER DTC OUTPUT RECURS

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the tester on.



e.

Start the engine.


f.

Allow the engine to idle for 2 minutes or more.


g.

Enter the following menus: Powertrain / Engine and ECT / DTC.


h.

Read DTCs.

Result
Result Proceed to
No DTC is output A
P0037, P0038, P0057, P0058, P102D and/or P105D are output B



A

B