Home › Engine / Hybrid System › 1UR-FE (ENGINE MECHANICAL) › DRIVE BELT
RM2660E _51 Engine / Hybrid System _052776 1UR-FE ENGINE MECHANICAL _0255034 DRIVE BELT A

1UR-FE ENGINE MECHANICAL  DRIVE BELT  INSTALLATION  


PROCEDURE

Hide 16361A 1.INSTALL FAN AND GENERATOR V BELT

a.
A163771E11
0.896,2.313 0.896,2.875 true 3.052,0.552 2.948,0.552 2.948,0.552 2.698,1.135 true 1.396,1.219 1.583,1.375 0.188,0.156 10 false *1 2.198,1.354 2.385,1.51 0.188,0.156 10 false *2 3.073,0.458 3.26,0.615 0.188,0.156 10 false *3 0.354,1.667 0.542,1.823 0.188,0.156 10 false *4 0.823,2.896 1.01,3.052 0.188,0.156 10 false *5 0.927,1.688 1.115,1.844 0.188,0.156 10 false *6 1.865,2.094 2.052,2.25 0.188,0.156 10 false *7 2.927,2.135 3.115,2.292 0.188,0.156 10 false *8

Set the fan and generator V belt onto every part.

Text in Illustration
*1 Water Pump Pulley
*2 Fan Pulley
*3 No. 1 Idler Pulley
*4 Vane Pump Pulley
*5 Generator Pulley
*6 V-ribbed Belt Tensioner
*7 Crankshaft Pulley
*8 Cooler Compressor Pulley


b.

While turning the belt tensioner counterclockwise, remove the pin.

NOTICE:

Make sure that the fan and generator V belt is properly set on each pulley.



c.

Check that the belt fits properly in the ribbed grooves.

HINT:

Make sure to check by hand that the belt has not slipped out of the grooves on the bottom of the pulley.



Hide 51405A 2.INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

Hide 53806 3.INSTALL FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH

Hide 53805 4.INSTALL FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH

Hide 11209 5.INSTALL V-BANK COVER SUB-ASSEMBLY

a.
A274416E01
0.256,2.98 0.436,3.142 0.180,0.163 10 *1 2.982,0.211 3.162,0.373 0.180,0.163 10 *4 2.752,0.842 2.933,1.005 0.180,0.163 10 *3 0.829,2.87 1.009,3.033 0.180,0.163 10 *2 0.345,2.98 0.345,2.892 0.345,2.892 0.385,2.805 false 0.829,2.958 0.67,2.958 false 2.734,0.932 2.675,0.932 2.675,0.932 2.649,0.746 false 2.971,0.304 2.9,0.304 2.9,0.304 2.86,0.45 false

Attach the 2 V-bank cover hooks to the bracket. Then align the 3 V-bank cover grommets with the 3 pins, and press down on the V-bank cover to attach the pins.

Text in Illustration
*1 Grommet
*2 Pin
*3 Hook
*4 Bracket