Home › Engine / Hybrid System › 1UR-FE (ENGINE MECHANICAL) › ENGINE ASSEMBLY › 2014.08–2015.08
RM2660E _51 Engine / Hybrid System _052776 1UR-FE ENGINE MECHANICAL _0255039 ENGINE ASSEMBLY A

1UR-FE ENGINE MECHANICAL  ENGINE ASSEMBLY  INSTALLATION  


PROCEDURE

Hide 12316A 1.INSTALL NO. 2 FRONT ENGINE MOUNTING BRACKET LH

a.

Install the No. 2 engine mounting bracket with the bolt.

Torque:
32 N*m (326 kgf*cm, 24 ft.*lbf)


Hide 12361 2.INSTALL FRONT ENGINE MOUNTING INSULATOR RH

a.

Install the mounting insulator with the nut.

Torque:
72 N*m (734 kgf*cm, 53 ft.*lbf)


Hide 12362A 3.INSTALL FRONT ENGINE MOUNTING INSULATOR LH

a.

Install the mounting insulator with the nut.

Torque:
72 N*m (734 kgf*cm, 53 ft.*lbf)


Hide 5.REMOVE ENGINE STAND

a.
A150148E02
0.096,0.562 0.280,0.716 0.185,0.155 10 *1 1.099,1.635 1.283,1.789 0.185,0.155 10 *2 1.096,0.563 1.281,0.718 0.185,0.155 10 *a 0.303,0.65 0.405,0.65 0.405,0.65 0.506,0.976 false 2.103,0.562 2.288,0.716 0.185,0.155 10 *1 2.09,0.65 1.988,0.65 1.988,0.65 1.886,0.976 false

Attach an engine sling device and hang the engine with a chain block.

Text in Illustration
*1 Engine Hanger
*2 Engine
*a 50° or less

NOTICE:

When hanging the engine, make sure to hang the engine with the angle of the sling device at 50° or less. Otherwise, the engine or engine hangers may be damaged.



b.

Lift the engine and remove it from the engine stand.

NOTICE:
·

With the exception of installing the engine assembly to an engine stand or removing the engine assembly from an engine stand, do not perform any work on the engine while it is suspended, as doing so is dangerous.

·

Pay attention to the angle of the sling device as the engine assembly or engine hangers may be damaged or deformed if the angle is incorrect.




c.

Place the engine onto a workbench.


Hide 6.INSTALL ENGINE ASSEMBLY

a.

Attach an engine sling device and hang the engine with a chain block.


b.

Slowly lower the engine into the engine compartment.


c.
A228361

Install the front engine mounting insulator LH and RH with the 2 nuts and 4 bolts.

Torque:
for nut : 72 N*m (734 kgf*cm, 53 ft.*lbf)
for bolt : 79 N*m (806 kgf*cm, 58 ft.*lbf)

Text in Illustration
V100135

Bolt
V100136

Nut


d.

Remove the 2 bolts and 2 engine hangers.


Hide 32101 7.INSTALL DRIVE PLATE AND RING GEAR SUB-ASSEMBLY

a.

Using SST, hold the crankshaft.

SST
09213-70011  (09213-70020)
09330-00021  


b.
A228418

Install the crankshaft angle sensor rotor.

Text in Illustration
V100135

Engine Side

HINT:
·

Align the pin hole of the crankshaft angle sensor rotor with the pin of the crankshaft.

·

As the crankshaft angle sensor rotor is not reversible, be sure to install it so that it is facing in the direction shown in the illustration.




c.
A228419E01
0.668,0.228 0.853,0.383 0.185,0.155 10 *1 3.177,2.339 3.362,2.494 0.185,0.155 10 *2 1.496,0.319 0.876,0.319 false 3.16,2.433 2.584,2.433 false

Install the drive plate and ring gear and the rear drive plate spacer to the crankshaft.

Text in Illustration
*1 Drive Plate and Ring Gear
*2 Rear Drive Plate Spacer
V100135

Transmission Side

HINT:

As the rear drive plate spacer and the drive plate and ring gear are not reversible, be sure to install them so that they are facing in the directions shown in the illustration.



d.

Install the drive plate and ring gear and bolts.

HINT:

The bolts are tightened in 2 progressive steps.


i.

Clean the bolts and bolt holes.


ii.
A192239E03
1.374,0.672 1.576,0.827 0.202,0.156 10 *1 1.569,0.758 1.672,0.758 1.672,0.758 1.821,1.24 false

Apply adhesive to 2 or 3 threads at the end of each of the 10 bolts.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent


Text in Illustration
*1 Adhesive


iii.
U115440E03
2.156,0.698 2.271,0.833 0.115,0.135 10 false 7 1.823,1.604 2.042,1.75 0.219,0.146 10 false 10 1.844,0.479 1.958,0.615 0.115,0.135 10 false 1 1.49,1.594 1.604,1.76 0.115,0.167 10 false 2 2.281,1.031 2.396,1.208 0.115,0.177 10 false 3 1.073,1.042 1.188,1.177 0.115,0.135 10 false 4 2.156,1.385 2.302,1.573 0.146,0.188 10 false 5 1.198,0.688 1.344,0.844 0.146,0.156 10 false 6 1.198,1.385 1.333,1.563 0.135,0.177 10 false 8 1.49,0.479 1.615,0.646 0.125,0.167 10 false 9

Step 1:

Uniformly install and tighten the 10 new bolts in several steps in the sequence shown in the illustration.

Torque:
30 N*m (301 kgf*cm, 22 ft.*lbf)


iv.

Mark the top of each drive plate installation bolt with paint.


v.

Step 2:

Tighten the drive plate installation bolts 90°.


vi.

Check that the painted marks are now at a 90° angle to the top.

NOTICE:

Do not start the engine for at least an hour after installing the drive plate.




Hide 87207A 9.INSTALL NO. 1 WATER BY-PASS PIPE (w/o ATF Warmer)

a.

Install the No. 1 water by-pass pipe with the 2 bolts.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


b.

Connect the water hose.


Hide 16268 10.INSTALL NO. 1 WATER BY-PASS PIPE (w/ ATF Warmer)

a.

Install the No. 1 water by-pass pipe with the 2 bolts.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


b.

w/ Rear Heater:

Connect the 6 water hoses.


c.

w/o Rear Heater:

Connect the 4 water hoses.


Hide 82121 17.CONNECT ENGINE WIRE

a.

w/ Secondary Air Injection System:

Connect the connector and clamp.


b.

Connect the 2 connectors and 2 clips to the engine room junction block.


c.

Connect the wire to the positive (+) battery cable with the nut.

Torque:
7.6 N*m (77 kgf*cm, 67 in.*lbf)


d.

Connect the clamp and ground wire with the bolt.

Torque:
for Type A : 8.4 N*m (86 kgf*cm, 74 in.*lbf)
for Type B : 10 N*m (102 kgf*cm, 7 ft.*lbf)

HINT:
A418191C01
0.375,0.219 0.688,0.375 0.313,0.156 10 false *A 2.135,0.219 2.448,0.375 0.313,0.156 10 false *B
*A for Type A
*B for Type B


Type A or B can be distinguished by confirming the mark on the bolt.



e.

w/ Secondary Air Injection System:

Connect the 2 air injection control driver connectors.


f.

Connect the 2 connectors and 2 clips to the engine room junction block.


g.

Connect the wire and 2 clips to the engine room junction block with the nut.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


h.

Connect the ground wire with the bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


i.

Connect the 4 connectors and 2 clamps to the connector holder block.


j.

Connect the wire harness clamp and ECM connector.

HINT:

Refer to the following procedures to connect the ECM connector (See page Engine / Hybrid System>1UR-FE (ENGINE CONTROL)>ECM>INSTALLATION).



Hide 23271F 18.CONNECT FUEL HOSE AND FUEL TUBE SUB-ASSEMBLY

a.

Connect the fuel hose and fuel tube sub-assembly (See page Engine / Hybrid System>1UR-FE (FUEL)>FUEL SYSTEM>PRECAUTION).


b.

Attach the clamp and install the fuel pipe clamp to the fuel tube connector.


Hide 17167 22.INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

Hide 17168 24.INSTALL NO. 2 EXHAUST MANIFOLD HEAT INSULATOR

Hide 17450B 28.INSTALL FRONT NO. 2 EXHAUST PIPE ASSEMBLY

Hide 89465 31.INSTALL HEATED OXYGEN SENSOR (for Bank 2 Sensor 2)

Hide 89465 32.INSTALL HEATED OXYGEN SENSOR (for Bank 1 Sensor 2)

Hide 17361 41.INSTALL AIR TUBE SUB-ASSEMBLY (w/ Secondary Air Injection System)

Hide 17343 45.CONNECT NO. 3 AIR INJECTION SYSTEM HOSE (w/ Secondary Air Injection System)

a.

Connect the No. 3 air injection system hose.


Hide 16572D 47.INSTALL NO. 2 RADIATOR HOSE

Hide 16571C 49.INSTALL NO. 1 RADIATOR HOSE

Hide 28800 51.INSTALL BATTERY

a.

Install the battery.


b.

Temporarily install the nut and install the bolt.


c.

Adjust the battery clamp's position.


d.

Tighten the 2 nuts and bolt.

Torque:
for bolt : 12 N*m (122 kgf*cm, 9 ft.*lbf)
for nut : 5.0 N*m (51 kgf*cm, 44 in.*lbf)


Hide 53784 52.INSTALL FRONT FENDER APRON TRIM PACKING C

Hide 53782 53.INSTALL FRONT FENDER APRON TRIM PACKING A

Hide 53785B 54.INSTALL FRONT FENDER APRON TRIM PACKING D

Hide 53783 55.INSTALL FRONT FENDER APRON TRIM PACKING B

Hide 55781E 56.INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

Hide 53301 57.INSTALL HOOD SUB-ASSEMBLY

a.
A274229

Install the hood with the 6 bolts.

Torque:
for bolt A : 13 N*m (133 kgf*cm, 10 ft.*lbf)
for bolt B : 18 N*m (178 kgf*cm, 13 ft.*lbf)

Text in Illustration
V100135

for Bolt A
V100136

for Bolt B


Hide 53301 58.ADJUST HOOD SUB-ASSEMBLY

Hide 53294C 59.INSTALL RADIATOR SIDE DEFLECTOR LH

Hide 53293C 60.INSTALL RADIATOR SIDE DEFLECTOR RH (w/o Air Cooled Transmission Oil Cooler)

Hide 32917 61.INSTALL TRANSMISSION OIL COOLER AIR DUCT (w/ Air Cooled Transmission Oil Cooler)

Hide 63.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 67.ADD POWER STEERING FLUID

Hide 73.INSPECT FOR POWER STEERING FLUID LEAK

Hide 51440 80.INSTALL OIL PAN PROTECTOR ASSEMBLY

a.

Install the oil pan protector assembly with the 4 bolts.

Torque:
63 N*m (642 kgf*cm, 46 ft.*lbf)


Hide 51442 81.INSTALL NO. 2 ENGINE UNDER COVER

a.

Install the No. 2 engine under cover with the 2 bolts.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)


Hide 51405A 82.INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

a.

Install the No. 1 engine under cover sub-assembly with the 10 bolts.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)