Home › Engine / Hybrid System › 1UR-FE (ENGINE MECHANICAL) › CAMSHAFT › 2015.08–2016.08
RM2660E _51 Engine / Hybrid System _052776 1UR-FE ENGINE MECHANICAL _0255035 CAMSHAFT A

1UR-FE ENGINE MECHANICAL  CAMSHAFT  INSTALLATION  


PROCEDURE

Hide 1.INSTALL CAMSHAFT BEARING CAP LH

a.

Apply a light coat of engine oil to the camshaft journals, camshaft housing and camshaft bearing caps.


b.

Install the No. 3 and No. 4 camshafts to the camshaft housing.


c.
A217487E04
2.281,0.156 2.469,0.344 0.188,0.188 9 false L2 1.813,0.156 1.979,0.354 0.167,0.198 9 false L3 1.354,0.146 1.531,0.333 0.177,0.188 9 false L4 0.823,0.156 0.99,0.333 0.167,0.177 9 false L5 1.365,1.896 1.531,2.083 0.167,0.188 9 false L3

Confirm the marks and numbers on the camshaft bearing caps and place them in their proper positions and directions.


d.
U115395E03
2.698,0.188 2.823,0.333 0.125,0.146 10 false 1 2.625,1.76 2.75,1.906 0.125,0.146 10 false 2 2.104,0.177 2.229,0.323 0.125,0.146 10 false 3 2.094,1.771 2.219,1.917 0.125,0.146 10 false 4 1.604,0.177 1.729,0.323 0.125,0.146 10 false 5 1.615,1.781 1.74,1.927 0.125,0.146 10 false 6 1.125,0.177 1.25,0.333 0.125,0.156 10 false 7 0.521,1.76 0.719,1.917 0.198,0.156 10 false 10 1.135,1.771 1.26,1.938 0.125,0.167 10 false 8 0.563,0.188 0.708,0.365 0.146,0.177 10 false 9

Temporarily install the 10 bolts in the order shown in the illustration.


Hide 11104A 2.INSTALL CAMSHAFT HOUSING SUB-ASSEMBLY LH

a.
A220131E01
2.494,0.02 2.678,0.175 0.185,0.155 10 *1 2.906,0.519 3.091,0.673 0.185,0.155 10 *2 0.646,0.711 0.831,0.865 0.185,0.155 10 *3 2.479,0.113 2.384,0.113 2.384,0.113 2.177,0.414 false 2.394,0.608 2.898,0.608 false 0.859,0.797 1.363,0.797 false

Check the valve rocker arms as shown in the illustration.

Text in Illustration
*1 Valve Rocker Arm
*2 Valve Stem Cap
*3 Valve Lash Adjuster


b.
A148278E05
0.716,1.784 0.910,1.931 0.194,0.147 10 *1

Apply seal packing in a continuous line as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard seal diameter:

3.5 to 4.0 mm (0.138 to 0.157 in.)


Text in Illustration
*1 Seal Packing

NOTICE:
·

Remove any oil from the contact surface.

·

Install the camshaft housing within 3 minutes and tighten the bolts within 15 minutes after applying seal packing.




c.
U115454E03
1.01,2.583 1.885,2.896 1.885,2.896 1.885,2.99 false 1.885,2.896 2.604,2.563 false 2.583,2.052 2.75,2.198 0.167,0.146 10 false 3° 0.708,2.115 0.958,2.26 0.25,0.146 10 false 45° 1.333,0.906 1.458,1.052 0.125,0.146 10 false 1 0.854,0.896 0.979,1.042 0.125,0.146 10 false 2 1.969,0.906 2.094,1.052 0.125,0.146 10 false 3 0.219,0.646 0.344,0.792 0.125,0.146 10 false 4 2.604,0.885 2.74,1.031 0.135,0.146 10 false 5 1.417,0.094 1.542,0.24 0.125,0.146 10 false 6 1.344,1.573 1.458,1.708 0.115,0.135 10 false 7 1.885,0.104 2.083,0.25 0.198,0.146 10 false 10 0.854,0.083 0.979,0.25 0.125,0.167 10 false 8 0.156,0.083 0.354,0.229 0.198,0.146 10 false 12 1.865,1.573 2.063,1.719 0.198,0.146 10 false 11 0.135,1.583 0.333,1.729 0.198,0.146 10 false 13 0.844,1.573 0.969,1.74 0.125,0.167 10 false 9 3.135,0.625 3.333,0.771 0.198,0.146 10 false 14 0.365,1.219 0.563,1.365 0.198,0.146 10 false 16 2.438,1.479 2.635,1.625 0.198,0.146 10 false 15 1.802,3.01 1.99,3.167 0.188,0.156 10 false *1 0.396,2.073 0.583,2.229 0.188,0.156 10 false *A 2.094,2.073 2.281,2.229 0.188,0.156 10 false *B 2.99,1.469 3.188,1.615 0.198,0.146 10 false 17 2.677,0.063 2.875,0.208 0.198,0.146 10 false 18

Install the camshaft housing, and then install the 18 bolts in the order shown in the illustration.

Torque:
for bolt A : 10 N*m (102 kgf*cm, 7 ft.*lbf)
except bolt A : 30 N*m (306 kgf*cm, 22 ft.*lbf)

Text in Illustration
*A for Intake Side
*B for Exhaust Side
*1 Knock Pin
V100135

Bolt
V100136

Bolt A

NOTICE:
·

Do not start the engine for at least 2 hours after the installation.

·

Make sure that the knock pins of the camshafts are positioned as shown in the illustration before installing the camshaft housing.




d.
U115358E03
2.885,0.188 3.01,0.333 0.125,0.146 10 false 1 3.115,1.521 3.26,1.708 0.146,0.188 10 false 2 2.177,0.188 2.313,0.354 0.135,0.167 10 false 3 2.167,1.771 2.323,1.969 0.156,0.198 10 false 4 1.625,0.188 1.76,0.365 0.135,0.177 10 false 5 1.604,1.781 1.781,1.969 0.177,0.188 10 false 6 1.073,0.188 1.208,0.375 0.135,0.188 10 false 7 0.385,1.781 0.635,1.969 0.25,0.188 10 false 10 1.031,1.781 1.219,1.99 0.188,0.208 10 false 8 0.438,0.177 0.573,0.344 0.135,0.167 10 false 9

Tighten the 10 bolts in the order shown in the illustration.

Torque:
16 N*m (163 kgf*cm, 12 ft.*lbf)

NOTICE:

Thoroughly wipe clean any seal packing.



Hide 3.INSTALL CAMSHAFT BEARING CAP RH

a.

Apply a light coat of engine oil to the camshaft journals, camshaft housing and camshaft bearing caps.


b.

Install the No. 1 and No. 2 camshafts to the camshaft housing.


c.
A160686E09
1.708,0.146 1.896,0.365 0.188,0.219 9 false R3 1.75,1.948 1.958,2.146 0.208,0.198 9 false R2 0.708,1.938 0.906,2.146 0.198,0.208 9 false R4 1.219,1.948 1.406,2.156 0.188,0.208 9 false R3 0.146,1.948 0.354,2.177 0.208,0.229 9 false R5

Confirm the marks and numbers on the camshaft bearing caps and place them in their proper positions and directions.


d.
U115342E03
2.781,1.74 2.917,1.906 0.135,0.167 10 false 1 3.052,0.417 3.177,0.563 0.125,0.146 10 false 2 2.104,1.75 2.26,1.948 0.156,0.198 10 false 3 2.104,0.198 2.229,0.344 0.125,0.146 10 false 4 1.552,1.75 1.729,1.969 0.177,0.219 10 false 5 1.552,0.177 1.677,0.323 0.125,0.146 10 false 6 1.01,1.74 1.188,1.958 0.177,0.219 10 false 7 0.323,0.188 0.521,0.333 0.198,0.146 10 false 10 1,0.188 1.156,0.354 0.156,0.167 10 false 8 0.365,1.75 0.521,1.938 0.156,0.188 10 false 9

Temporarily install the 10 bolts in the order shown in the illustration.


Hide 11103C 4.INSTALL CAMSHAFT HOUSING SUB-ASSEMBLY RH

a.
A220131E01
2.494,0.02 2.678,0.175 0.185,0.155 10 *1 2.906,0.519 3.091,0.673 0.185,0.155 10 *2 0.646,0.711 0.831,0.865 0.185,0.155 10 *3 2.479,0.113 2.384,0.113 2.384,0.113 2.177,0.414 false 2.394,0.608 2.898,0.608 false 0.859,0.797 1.363,0.797 false

Check the valve rocker arms as shown in the illustration.

Text in Illustration
*1 Valve Rocker Arm
*2 Valve Stem Cap
*3 Valve Lash Adjuster


b.
A148275E06
0.7,1.788 0.890,1.932 0.189,0.144 10 *1

Apply seal packing in a continuous line as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard seal diameter:

3.5 to 4.0 mm (0.138 to 0.157 in.)


Text in Illustration
*1 Seal Packing

NOTICE:
·

Remove any oil from the contact surface.

·

Install the camshaft housing within 3 minutes and tighten the bolts within 15 minutes after applying seal packing.




c.
U115455E03
0.938,2.646 1.771,2.927 1.771,2.927 1.771,3.01 false 1.771,2.927 2.323,2.74 false 0.719,2.125 0.958,2.271 0.24,0.146 10 false 55° 2.094,2.177 2.333,2.323 0.24,0.146 10 false 70° 1.646,1.01 1.771,1.156 0.125,0.146 10 false 1 1.042,1.021 1.167,1.167 0.125,0.146 10 false 2 2.156,1.021 2.281,1.167 0.125,0.146 10 false 3 0.417,1.01 0.542,1.156 0.125,0.146 10 false 4 2.802,0.99 2.927,1.135 0.125,0.146 10 false 5 1.24,1.594 1.365,1.74 0.125,0.146 10 false 6 1.531,0.083 1.646,0.219 0.115,0.135 10 false 7 1.708,1.583 1.906,1.729 0.198,0.146 10 false 10 0.688,1.573 0.854,1.74 0.167,0.167 10 false 8 0.406,1.865 0.604,2.01 0.198,0.146 10 false 12 2.146,0.354 2.344,0.5 0.198,0.146 10 false 11 0.427,0.083 0.625,0.229 0.198,0.146 10 false 13 1.021,0.073 1.177,0.24 0.156,0.167 10 false 9 2.927,1.271 3.125,1.417 0.198,0.146 10 false 14 0.302,0.635 0.5,0.781 0.198,0.146 10 false 16 2.719,0.417 2.917,0.563 0.198,0.146 10 false 15 1.677,3.031 1.865,3.188 0.188,0.156 10 false *1 0.354,2.125 0.542,2.281 0.188,0.156 10 false *A 1.792,2.125 1.979,2.281 0.188,0.156 10 false *B 3.167,0.031 3.365,0.177 0.198,0.146 10 false 17 2.26,1.708 2.458,1.854 0.198,0.146 10 false 18

Install the camshaft housing, and then install the 18 bolts in the order shown in the illustration.

Torque:
for bolt A : 10 N*m (102 kgf*cm, 7 ft.*lbf)
except bolt A : 30 N*m (306 kgf*cm, 22 ft.*lbf)

Text in Illustration
*A for Exhaust Side
*B for Intake Side
*1 Knock Pin
V100135

Bolt
V100136

Bolt A

NOTICE:
·

Do not start the engine for at least 2 hours after the installation.

·

Make sure that the knock pins of the camshafts are positioned as shown in the illustration before installing the camshaft housing.




d.
U115340E03
2.802,1.688 2.927,1.865 0.125,0.177 10 false 1 3.021,0.406 3.188,0.604 0.167,0.198 10 false 2 2.125,1.688 2.292,1.875 0.167,0.188 10 false 3 2.094,0.177 2.26,0.365 0.167,0.188 10 false 4 1.563,1.688 1.729,1.875 0.167,0.188 10 false 5 1.542,0.177 1.688,0.385 0.146,0.208 10 false 6 0.99,1.688 1.125,1.875 0.135,0.188 10 false 7 0.323,0.146 0.521,0.292 0.198,0.146 10 false 10 0.958,0.156 1.125,0.333 0.167,0.177 10 false 8 0.365,1.688 0.542,1.906 0.177,0.219 10 false 9

Tighten the 10 bolts in the order shown in the illustration.

Torque:
16 N*m (163 kgf*cm, 12 ft.*lbf)

NOTICE:

Thoroughly wipe clean any seal packing.



Hide 13550 5.INSTALL NO. 2 CHAIN TENSIONER ASSEMBLY

a.
A214843E05
1.958,2.313 1.885,2.313 1.885,2.313 1.646,2.49 false 1.667,2.927 1.74,2.927 1.74,2.927 1.885,2.625 false 2.833,1.688 2.833,2.302 true 1.969,2.219 2.156,2.375 0.188,0.156 10 false *1 1.458,2.844 1.646,3 0.188,0.156 10 false *2 2.323,0.927 2.594,1.146 0.271,0.219 10 true *a 2.74,2.323 2.927,2.479 0.188,0.156 10 false *2

Install the No. 2 chain tensioner with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

Text in Illustration
*1 Plunger
*2 Pin
*a Push


b.

While raising up the No. 2 chain tensioner, insert a pin with a diameter of 1.0 mm (0.0394 in.) into the hole to fix the tensioner in place.


Hide 13506 6.INSTALL NO. 1 CHAIN SUB-ASSEMBLY RH

a.
A160662E04
2.326,0.955 2.611,1.206 0.285,0.251 2.002,0.119 2.187,0.273 0.185,0.155 10 *1 2.36,0.999 2.545,1.154 0.185,0.155 10 *2 2.462,0.702 2.462,0.98 false 2.21,0.202 2.603,0.202 2.603,0.202 2.603,0.608 false 2.376,0.568 2.376,0.202 false

Align the No. 1 chain's mark plates (orange) with the camshaft timing gear's timing mark and attach the chain to the gear as shown in the illustration.

Text in Illustration
*1 Mark Plate (Orange)
*2 Timing Mark


b.
A149461E05
0.677,1.205 0.862,1.360 0.185,0.155 10 *1 2.593,1.758 2.778,1.912 0.185,0.155 10 *2 0.885,1.288 1,1.288 1,1.288 1.901,1.76 false 2.077,1.846 2.573,1.846 false

Align the No. 1 chain's mark plate (orange) with the crankshaft timing gear's timing mark and attach the chain to the gear as shown in the illustration.

Text in Illustration
*1 Timing Mark
*2 Mark Plate (Orange)


c.
A160663E04
0.275,0.053 0.460,0.207 0.185,0.155 10 *1 0.78,1.983 0.964,2.138 0.185,0.155 10 *2 0.878,1.135 0.878,1.971 false 2.646,1.798 2.830,1.953 0.185,0.155 10 *2 2.744,1.139 2.744,1.786 false 0.483,0.141 0.576,0.141 0.576,0.141 0.855,0.736 false 2.141,0.053 2.326,0.207 0.185,0.155 10 *1 2.349,0.141 2.442,0.141 2.442,0.141 2.748,0.792 false

Align the No. 2 chain's mark plates (yellow) with the timing marks (1-dot marks) of the camshaft timing gear and camshaft timing exhaust gear, and attach the No. 2 chain to the gears as shown in the illustration.

Text in Illustration
*1 Timing Mark
*2 Mark Plate (Yellow)

HINT:

The crankshaft timing gear and camshaft exhaust gear are installed with the No. 1 and No. 2 chains connected to the gears.



d.

Install the crankshaft timing sprocket RH to the crankshaft.


e.

Align the knock pin of the No. 1 camshaft with the pin hole of the camshaft timing gear and install the camshaft timing gear.


f.

Using the hexagonal portion of the No. 2 camshaft, align the knock pin of the No. 2 camshaft with the pin hole of the camshaft timing exhaust gear and install the camshaft timing exhaust gear.


g.

Remove the pin from the No. 2 chain tensioner.


Hide 13561 7.INSTALL NO. 1 CHAIN VIBRATION DAMPER RH

a.

Install the No. 1 chain vibration damper RH with the 2 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 13559 8.INSTALL CHAIN TENSIONER SLIPPER RH

HINT:

If the No. 1 chain tensioner slipper cannot be installed due to the tension of the chain, use the hexagonal portion of the camshaft to loosen the chain, and then install the chain tensioner slipper RH.


Hide 13540 9.INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY RH

a.
A148260E03
0.157,0.888 0.342,1.043 0.185,0.155 10 *1 3.086,1.631 3.271,1.785 0.185,0.155 10 *2 1.968,0.977 0.366,0.977 false 1.266,1.553 0.494,1.553 0.494,1.553 0.494,0.975 false 3.068,1.722 2.002,1.722 false 2.959,1.724 2.959,1.113 2.959,1.113 2.445,1.113 false

Move the stopper plate upward to release the lock and push the plunger deep into the No. 1 chain tensioner.

Text in Illustration
*1 Stopper Plate
*2 Plunger


b.

Move the stopper plate downward to set the lock and insert a hexagon wrench into the hole of the stopper plate.


c.

Install the No. 1 chain tensioner with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


d.

Remove the hexagon wrench from the No. 1 chain tensioner.


Hide 13560A 10.INSTALL NO. 3 CHAIN TENSIONER ASSEMBLY

a.
A214842E04
1.771,2.417 1.854,2.417 1.854,2.417 2.031,2.302 false 2.083,1.813 2,1.813 2,1.813 1.823,2.156 false 0.906,2.417 1,2.417 1,2.417 1.302,1.896 false 2.104,1.729 2.292,1.885 0.188,0.156 10 false *1 1.563,2.333 1.75,2.49 0.188,0.156 10 false *2 2.469,0.385 2.76,0.698 0.292,0.313 10 true *a 0.698,2.323 0.885,2.479 0.188,0.156 10 false *1

Install the No. 3 chain tensioner with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

Text in Illustration
*1 Pin
*2 Plunger
*a Push


b.

While pushing down the No. 3 chain tensioner, insert a pin with a diameter of 1.0 mm (0.0394 in.) into the hole to fix the tensioner in place.


Hide 13506 11.INSTALL NO. 1 CHAIN SUB-ASSEMBLY LH

a.
A160665E04
0.497,0.199 0.682,0.353 0.185,0.155 10 *1 0.214,1.21 0.399,1.365 0.185,0.155 10 *2 0.705,0.285 1.105,0.285 1.105,0.285 1.105,0.59 false 0.858,0.636 0.858,0.285 false 0.421,1.3 0.529,1.3 0.529,1.3 1.011,0.71 false

Align the No. 1 chain's mark plates (orange) with the camshaft timing gear's timing mark and attach the chain to the gear as shown in the illustration.

Text in Illustration
*1 Mark Plate (Orange)
*2 Timing Mark


b.
A149462E05
0.661,1.383 0.846,1.537 0.185,0.155 10 *1 0.661,1.764 0.846,1.919 0.185,0.155 10 *2 1.691,1.473 0.868,1.473 false 1.577,1.734 0.991,1.853 0.991,1.853 0.868,1.853 false

Align the No. 1 chain's mark plate (orange) with the crankshaft timing gear's timing mark and attach the chain to the gear as shown in the illustration.

Text in Illustration
*1 Timing Mark
*2 Mark Plate (Orange)


c.
A160666E04
0.363,0.185 0.548,0.339 0.185,0.155 10 *1 0.698,1.957 0.883,2.112 0.185,0.155 10 *2 0.798,1.132 0.798,1.946 false 2.062,1.957 2.247,2.112 0.185,0.155 10 *2 2.477,1.03 2.162,1.858 2.162,1.858 2.162,1.946 false 0.825,0.788 0.659,0.271 0.659,0.271 0.57,0.271 false 1.995,0.015 2.180,0.170 0.185,0.155 10 *1 2.466,0.651 2.291,0.102 2.291,0.102 2.202,0.102 false

Align the No. 2 chain's mark plates (yellow) with the timing marks (1-dot marks) of the camshaft timing gear and camshaft timing exhaust gear, and attach the No. 2 chain to the gears as shown in the illustration.

Text in Illustration
*1 Timing Mark
*2 Mark Plate (Yellow)

HINT:

The crankshaft timing gear and camshaft exhaust gear are installed with the No. 1 and No. 2 chains connected to the gears.



d.

Install the crankshaft timing sprocket LH to the crankshaft.


e.

Align the knock pin of the No. 3 camshaft with the pin hole of the camshaft timing gear and install the camshaft timing gear.


f.

Using the hexagonal portion of the No. 4 camshaft, align the knock pin of the No. 4 camshaft with the pin hole of the camshaft timing exhaust gear and install the camshaft timing exhaust gear.

NOTICE:

Because the gears' timing mark positions may shift due to looseness of the No. 1 chain, use the hexagonal portion of the camshaft to hold the No. 3 camshaft in place until the No. 1 chain tensioner is installed.



g.

Remove the pin from the No. 3 chain tensioner.


Hide 13559 12.INSTALL CHAIN TENSIONER SLIPPER LH

HINT:

If the chain tensioner slipper cannot be installed due to the tension of the chain, use the hexagonal portion of the camshaft to loosen the chain and install the chain tensioner slipper LH.


Hide 13540 13.INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY LH

a.
A148260E04
0.179,0.873 0.363,1.028 0.185,0.155 10 *1 2.886,1.633 3.070,1.787 0.185,0.155 10 *2 1.968,0.963 0.39,0.963 false 1.262,1.564 0.521,1.564 0.521,1.564 0.521,0.963 false 2.868,1.722 2.006,1.722 false 2.71,1.723 2.71,1.089 2.71,1.089 2.454,1.089 false

Move the stopper plate upward to release the lock and push the plunger deep into the No. 1 chain tensioner.

Text in Illustration
*1 Stopper Plate
*2 Plunger


b.

Move the stopper plate downward to set the lock and insert a hexagon wrench into the hole of the stopper plate.


c.

Install a new gasket and the No. 1 chain tensioner with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 13561 14.INSTALL NO. 1 CHAIN VIBRATION DAMPER LH

a.

Install the No. 1 chain vibration damper with the 2 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


b.

Remove the hexagon wrench from the No. 1 chain tensioner.


Hide 13050 15.TIGHTEN CAMSHAFT TIMING GEAR ASSEMBLY

a.

for Bank 1:

i.
A214802E05
2.917,0.208 3.146,0.438 0.229,0.229 10 true *a

Using a wrench to hold the hexagonal portion of the No. 3 camshaft, install the camshaft timing gear bolt.

Torque:
100 N*m (1020 kgf*cm, 74 ft.*lbf)

Text in Illustration
*a Hold
V100135

Turn


ii.
A214803E06
3.146,0.427 3.427,0.667 0.281,0.24 10 true *a

Using a wrench to hold the hexagonal portion of the No. 4 camshaft, install the camshaft timing exhaust gear bolt.

Torque:
100 N*m (1020 kgf*cm, 74 ft.*lbf)

Text in Illustration
*a Hold
V100135

Turn



b.

for Bank 2:

i.
A228432E01
1.172,0.083 1.357,0.238 0.185,0.155 10 *a

Using a wrench to hold the hexagonal portion of the No. 1 camshaft, install the camshaft timing gear bolt.

Torque:
100 N*m (1020 kgf*cm, 74 ft.*lbf)

Text in Illustration
*a Hold
V100135

Turn


ii.
A228433E01
0.754,0.238 0.938,0.393 0.185,0.155 10 *a

Using a wrench to hold the hexagonal portion of the No. 2 camshaft, install the camshaft timing exhaust gear bolt.

Torque:
100 N*m (1020 kgf*cm, 74 ft.*lbf)

Text in Illustration
*a Hold
V100135

Turn



Hide 11302 17.INSTALL TIMING CHAIN COVER SUB-ASSEMBLY