16322
1.INSTALL WATER INLET PIPE
Apply soapy water to 2 new O-rings and install them to the water inlet pipe.
Install the water inlet pipe to the No. 1 heat exchanger cover.
11302
2.INSTALL TIMING CHAIN COVER SUB-ASSEMBLY
Apply a light coat of engine oil to a new gasket.
Install the gasket to the cylinder block.
Apply a light coat of engine oil to a new O-ring.
Install the O-ring to the oil pan.
Apply seal packing in a continuous line to the timing chain cover as shown in the following illustration.
| *1 | Continuous Line Area | *2 | Dashed Line Area |
| *3 | Diagonal Line Area | - | - |
| *a | 20.0 mm (0.787 in.) | *b | 26.0 mm (1.02 in.) |
| *c | 16.0 mm (0.630 in.) | *d | 18.0 mm (0.709 in.) |
| *e | 7.0 mm (0.276 in.) | - | - |
Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
| Area | Seal Packing Diameter | Application Position from Inside Edge of Cover |
|---|---|---|
| Continuous line area | 3.0 to 4.0 mm (0.118 to 0.157 in.) | 2.5 mm (0.0984 in.) |
| Dashed line area | 6.4 mm (0.252 in.) or more, or within OK area shown in illustration | 7.0 mm (0.276 in.) |
| Diagonal line area | 3.0 to 4.0 mm (0.118 to 0.157 in.) | 5.5 mm (0.217 in.) |
| *1 | Seal Packing Thickness mm (in.) |
| *2 | Seal Packing Width mm (in.) |
| *3 | Thickness |
| *4 | Width |
|
OK Area |
When the contact surfaces are wet, wipe them with an oil-free cloth before applying seal packing.
Install the chain cover within 3 minutes and tighten the bolts within 10 minutes after applying seal packing.
Align the oil pump drive rotor spline and crankshaft as shown in the illustration and install the chain cover.
Temporarily install the 26 bolts and nut.
| Item | Length | Thread Diameter |
|---|---|---|
| Bolt A | 25 mm (0.984 in.) | 8 mm (0.315 in.) |
| Bolt B | 55 mm (2.17 in.) | 8 mm (0.315 in.) |
| Bolt C | 70 mm (2.76 in.) | 8 mm (0.315 in.) |
| Bolt D | 35 mm (1.38 in.) | 10 mm (0.394 in.) |
| Bolt E | 55 mm (2.17 in.) | 10 mm (0.394 in.) |
| Bolt F | 80 mm (3.15 in.) | 10 mm (0.394 in.) |
| *1 | Nut |
Make sure that there is no oil on the bolt threads.
Tighten the 3 bolts in several steps in the sequence shown in the illustration.
Temporarily install the fan bracket with the 5 bolts.
| Item | Length | Thread Diameter |
|---|---|---|
| Bolt A | 70 mm (2.76 in.) | 8 mm (0.315 in.) |
| Bolt B | 80 mm (3.15 in.) | 10 mm (0.394 in.) |
|
Bolt A |
|
Bolt B |
Temporarily install the belt tensioner with the bolt and 6 mm hexagon bolt.
|
Bolt |
|
6 mm Hexagon Bolt |
Tighten the 8 bolts labeled 4 to 11 in several steps in the sequence shown in the illustration.
Tighten the 22 bolts and nut labeled 12 to 34 in several steps in the sequence shown in the illustration.
Do not start the engine for at least 2 hours after the installation.
After the installation, if the seal packing has seeped out at the areas labeled A shown in the illustration, wipe it off.
|
Labeled A |
Check the torque of each bolt and nut again.
11301C
3.INSTALL FRONT CRANKSHAFT OIL SEAL
11202
4.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY LH
Install 5 new gaskets to the camshaft bearing caps (No. 2, No. 3).
Install a new cylinder head cover gasket LH to the cylinder head cover sub-assembly LH.
Remove any oil from the contact surface.
Apply seal packing as shown in the illustration.
Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
|
Seal Packing |
Remove any oil from the contact surface.
Install the cylinder head cover within 3 minutes and tighten the bolts within 15 minutes after applying seal packing.
Install a new seal washer to the bolt.
Temporarily install the cylinder head cover sub-assembly LH with the 14 bolts. Tighten the bolts uniformly in several steps.
| Item | Length | Thread Diameter |
|---|---|---|
| Bolt A | 70 mm (2.76 in.) | 8 mm (0.315 in.) |
| Bolt B | 25 mm (0.984 in.) | 6 mm (0.236 in.) |
|
Bolt A |
|
Bolt B |
Do not start the engine for at least 2 hours after the installation.
11201
5.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY RH
Install 5 new gaskets to the camshaft bearing caps. (No. 1, No. 3).
Install a new cylinder head cover gasket RH to the cylinder head cover sub-assembly RH.
Remove any oil from the contact surface.
Apply seal packing as shown in the illustration.
Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
|
Seal Packing |
Remove any oil from the contact surface.
Install the cylinder head cover within 3 minutes and tighten the bolts within 15 minutes after applying seal packing.
Install a new seal washer to the bolt.
Temporarily install the cylinder head cover sub-assembly RH with the 14 bolts. Tighten the bolts uniformly in several steps.
| Item | Length | Thread Diameter |
|---|---|---|
| Bolt A | 70 mm (2.76 in.) | 8 mm (0.315 in.) |
| Bolt B | 25 mm (0.984 in.) | 6 mm (0.236 in.) |
|
Bolt A |
|
Bolt B |
Do not start the engine for at least 2 hours after the installation.
19500
6.INSTALL IGNITION COIL ASSEMBLY
13471
7.INSTALL CRANKSHAFT PULLEY
Align the key groove of the pulley with the pulley set key, and slide on the pulley to install it.
Using SST, install the pulley set bolt.
| *a | Hold |
|
Turn |
16603
8.INSTALL NO. 1 IDLER PULLEY SUB-ASSEMBLY
Install the No. 1 idler pulley with the bolt.
16173
9.INSTALL WATER PUMP PULLEY
16355
10.INSTALL FRONT WATER BY-PASS JOINT
Install 2 new gaskets and the water by-pass joint with the 4 nuts.
16323
11.INSTALL WATER INLET HOUSING
16206
12.INSTALL WATER BY-PASS PIPE SUB-ASSEMBLY
Install the water by-pass pipe sub-assembly with the 2 bolts.
Connect the No. 2 water by-pass hose from the front water by-pass joint.
16281F
13.CONNECT NO. 5 WATER BY-PASS HOSE
16278K
14.INSTALL NO. 2 WATER BY-PASS PIPE SUB-ASSEMBLY
16261G
15.INSTALL NO. 1 WATER BY-PASS HOSE
16261L
16.CONNECT WATER BY-PASS HOSE
16268
17.INSTALL NO. 1 WATER BY-PASS PIPE
Connect the No. 1 water by-pass pipe with the 2 bolts.
Connect the heater water hose.
17363Q
18.INSTALL NO. 3 AIR TUBE (w/ Secondary Air Injection System)
Install a new gasket to the No. 3 air tube.
Install the No. 3 air tube with the 2 stud bolts, 2 nuts and bolt.
| *1 | No. 3 Air Tube |
| *2 | Claw |
| *3 | Exhaust Manifold |
Make sure the claws of the gasket are not caught between the No. 3 air tube and exhaust manifold.
17364A
19.INSTALL NO. 4 AIR TUBE (w/ Secondary Air Injection System)
Install a new gasket to the No. 4 air tube.
Install the No. 4 air tube with the 2 stud bolts, 2 nuts and bolt.
| *1 | No. 4 Air Tube |
| *2 | Claw |
| *3 | Exhaust Manifold |
Make sure the claws of the gasket are not caught between the No. 4 air tube and exhaust manifold.
Install the wire harness clamp bracket with the bolt.
77259E
20.INSTALL FUEL HOSE
Install the fuel hose (See page Engine / Hybrid System>1UR-FE (FUEL)>FUEL SYSTEM>PRECAUTION).
Install the fuel pipe clamp.
Connect the 2 clamps.
23902
21.INSTALL FUEL TUBE SUB-ASSEMBLY
Install the fuel tube (See page Engine / Hybrid System>1UR-FE (FUEL)>FUEL SYSTEM>PRECAUTION).
Install the 2 bolts.
12613
22.INSTALL NO. 3 ENGINE COVER
12614
23.INSTALL NO. 4 ENGINE COVER
27020
24.INSTALL GENERATOR ASSEMBLY
32907A
25.CONNECT OIL COOLER TUBE
44310
26.CONNECT VANE PUMP ASSEMBLY
Before performing the following procedures, move the spacer until the vane pump can be installed.
|
Spacer |
Connect the vane pump to the timing chain cover with the 2 bolts.
27.CONNECT POWER STEERING OIL PRESSURE SWITCH CONNECTOR
11452
28.INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE
15671
29.INSTALL OIL FILTER BRACKET
15781
30.INSTALL NO. 1 OIL COOLER BRACKET
83520
31.INSTALL OIL PRESSURE SENDER GAUGE ASSEMBLY
32.INSTALL OIL FILTER ELEMENT
33.CONNECT ENGINE WIRE
Connect the clamp and engine wire with the bolt.
for Engine Room RH Side:
Connect the 6 clamps.
Connect the noise filter connector.
Connect the injector connector.
Connect the 2 VVT sensor connectors.
Connect the 4 ignition coil connectors.
Connect the 2 camshaft timing oil control valve connectors.
for Engine Room LH Side:
Install the ground wire with the bolt.
Connect the 8 clamps.
Connect the noise filter connector.
Connect the engine coolant temperature sensor connector.
Connect the camshaft position sensor connector.
Connect the 2 VVT sensor connectors.
Connect the 4 ignition coil connectors.
Connect the 2 camshaft timing oil control valve connectors.
Connect the injector connector.
17361
34.INSTALL AIR TUBE (w/ Secondary Air Injection System)
Install the air tube with the 2 bolts.
Connect the No. 3 air injection system hose.
Attach the wire harness clamp.
25710
35.INSTALL AIR SWITCHING VALVE ASSEMBLY (w/ Secondary Air Injection System)
88320
36.CONNECT COOLER COMPRESSOR ASSEMBLY
Install the cooler compressor with the stud bolt.
Install the 3 bolts and nut.
Tighten the bolts and nut in the order shown in the illustration to install the cooler compressor.
17111
37.INSTALL INTAKE MANIFOLD
16400
38.INSTALL RADIATOR ASSEMBLY
39.INSTALL AIR CLEANER AND HOSE
53782
40.INSTALL FRONT FENDER APRON TRIM PACKING A
42.ADD ENGINE COOLANT
43.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
44.INSPECT ENGINE OIL LEVEL
45.INSPECT FOR OIL LEAK
46.INSPECT FOR COOLANT LEAK
11209
47.INSTALL V-BANK COVER SUB-ASSEMBLY