Home › Engine / Hybrid System › 1UR-FE (ENGINE MECHANICAL) › ENGINE UNIT
RM2660E _51 Engine / Hybrid System _052776 1UR-FE ENGINE MECHANICAL _0255040 ENGINE UNIT A

1UR-FE ENGINE MECHANICAL  ENGINE UNIT  REASSEMBLY  


PROCEDURE

Hide 1.INSTALL STUD BOLT

A214796E02
1.855,2.16 3.117,2.330 1.262,0.170 10 24.5 mm (0.965 in.) 1.665,2.973 2.743,3.143 1.078,0.170 10 40 mm (1.58 in.) 1.855,2.57 2.999,2.740 1.144,0.170 10 14 mm (0.551 in.) 1.801,2.245 1.672,2.245 1.672,2.245 1.049,2.706 false 1.801,2.664 1.672,2.664 1.672,2.664 1.049,3.125 false 1.635,3.054 1.524,3.054 false

NOTICE:

If a stud bolt is deformed or its threads are damaged, replace it.


a.

Install the timing chain cover stud bolts.

i.

Using an E10 "TORX" socket wrench, install the 2 stud bolts as shown in the illustration.

Torque:
20 N*m (199 kgf*cm, 14 ft.*lbf)



b.
U163694E02
0.406,3.375 0.656,3.375 0.656,3.375 0.656,3.979 false 0.406,3.688 0.656,3.688 false 2.354,4 2.354,3.74 2.354,3.74 2.073,3.74 false 2.573,2.573 2.51,2.573 2.51,2.573 2.073,3.438 false 0.938,3.375 1.615,3.698 0.677,0.323 10 false 19 mm (0.748 in.) 0.094,4.021 1.146,4.208 1.052,0.188 10 false 9 mm (0.354 in.) 1.625,4.021 2.76,4.208 1.135,0.188 10 false 12 mm (0.472 in.) 2.615,3.354 3.208,3.708 0.594,0.354 10 false 39 mm (1.54 in.) 2.615,2.49 3.281,2.813 0.667,0.323 10 false 22 mm (0.866 in.) 0.177,2.948 0.302,3.104 0.125,0.156 10 false A 1.854,2.948 1.979,3.104 0.125,0.156 10 false B 0.281,1.406 0.406,1.563 0.125,0.156 10 false A 2.188,2.479 2.313,2.635 0.125,0.156 10 false B 1.771,0.104 1.896,0.26 0.125,0.156 10 false A

Install the No. 1 oil pan stud bolts.

i.

Using E6 and E7 "TORX" socket wrenches, install the 3 stud bolts as shown in the illustration.

Torque:
for stud bolt A : 5.0 N*m (51 kgf*cm, 44 in.*lbf)
for stud bolt B : 9.0 N*m (92 kgf*cm, 80 in.*lbf)



Hide 2.INSTALL RING PIN

U115389E03
0.438,1.521 0.563,1.667 0.125,0.146 10 false A 2.833,1.531 2.958,1.677 0.125,0.146 10 false B 0.625,1.938 0.75,2.083 0.125,0.146 10 false A 2.865,1.844 2.99,1.99 0.125,0.146 10 false B 0.5,2.427 0.625,2.573 0.125,0.146 10 false A 1.938,2.427 2.063,2.573 0.125,0.146 10 false B

NOTICE:

It is not necessary to remove a ring pin unless it is being replaced.


a.

Using a plastic-faced hammer, tap in new ring pins to the timing chain cover.

Standard Protrusion:
Item Ring Pin Diameter Specified Condition
Ring pin A 13 mm (0.512 in.) 7.5 to 8.5 mm (0.295 to 0.335 in.)
Ring pin B 11 mm (0.433 in.) 3.6 to 4.6 mm (0.142 to 0.181 in.)



Hide 12109A 3.INSTALL OIL DRAIN PIPE SUB-ASSEMBLY

a.

Apply a light coat of engine oil to a new O-ring.


b.

Install the O-ring to the oil drain pipe.


c.

Install the oil drain pipe with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 11381A 4.INSTALL REAR CRANKSHAFT OIL SEAL

a.

Apply MP grease to the lip of a new rear crankshaft oil seal.

NOTICE:
·

Do not allow foreign matter to contact the lip of the oil seal.

·

Do not allow MP grease to contact the dust seal.




b.
A148433E03
0.029,0.79 0.349,0.937 0.320,0.147 10 SST 1.069,0.884 0.404,0.884 false 0.847,1.258 0.522,1.258 0.522,1.258 0.522,0.881 false

Using SST, tap in a rear crankshaft oil seal until its surface is flush with the rear engine oil seal retainer edge.

SST
09223-15030  
09950-70010  (09951-07100)

Standard depth:

0 to 1.0 mm (0 to 0.0394 in.)


NOTICE:
·

Keep the lip free from foreign matter.

·

Do not tap the rear crankshaft oil seal at an angle.




Hide 11381 5.INSTALL REAR ENGINE OIL SEAL RETAINER

a.
A148434E17
3.083,1.479 3.083,1.74 true 0.344,1.469 0.344,1.729 true 1.313,0.104 1.406,0.104 1.406,0.104 1.5,0.438 false 2.885,1.75 3.385,1.896 0.5,0.146 10 false 3.5 mm 0.156,1.75 0.656,1.896 0.5,0.146 10 false 3.5 mm 1.167,0.031 1.354,0.188 0.188,0.156 10 false *1

Apply seal packing in a continuous line as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Seal diameter:

2.0 to 3.0 mm (0.0787 to 0.118 in.)


Application position from inside edge of retainer:

3.5 mm (0.138 in.)


Text in Illustration
*1 Seal Packing

NOTICE:
·

Remove any oil from the contact surface.

·

Install the rear engine oil seal retainer within 3 minutes and tighten the bolts and nuts within 15 minutes after applying seal packing.




b.

Install the rear engine oil seal retainer with the 6 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

NOTICE:
·

Do not start the engine for at least 2 hours after installing the rear engine oil seal retainer.

·

When installing the rear engine oil seal retainer, make sure the lip of the rear crankshaft oil seal is not damaged.

·

When installing the rear engine oil seal retainer, make sure the lip of the rear crankshaft oil seal is not folded incorrectly.




Hide 15104 6.INSTALL OIL STRAINER SUB-ASSEMBLY

a.

Apply a light coat of engine oil to a new O-ring.


b.

Install the O-ring to the oil strainer.


c.

Install the oil strainer with the 2 bolts.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)

NOTICE:

Make sure the O-ring is not twisted or damaged.



Hide 12121 7.INSTALL NO. 1 OIL PAN BAFFLE PLATE

a.

Install the No. 1 oil pan baffle plate with the 7 bolts.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 12101 8.INSTALL NO. 1 OIL PAN SUB-ASSEMBLY

a.
A228289E01
0.846,0.041 1.031,0.196 0.185,0.155 10 *1 1.054,0.132 1.162,0.132 1.162,0.132 1.254,0.551 false

Apply seal packing in a continuous line as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard seal diameter:

3.0 to 4.0 mm (0.118 to 0.157 in.)


Text in Illustration
*1 Seal Packing

NOTICE:
·

Remove any oil from the contact surface.

·

Install the No. 1 oil pan within 3 minutes and tighten the bolts and nuts within 15 minutes after applying seal packing.




b.
A385817E01
3,0.719 3.156,0.917 0.156,0.198 10 false A 3,1.052 3.156,1.25 0.156,0.198 10 false A 2.51,0.042 2.667,0.24 0.156,0.198 10 false B 2.167,0.073 2.323,0.271 0.156,0.198 10 false B 1.854,0.073 2.01,0.271 0.156,0.198 10 false B 1.469,0.073 1.625,0.271 0.156,0.198 10 false B 1.052,0.063 1.208,0.26 0.156,0.198 10 false B 0.375,0.354 0.531,0.552 0.156,0.198 10 false B 0.375,1.365 0.531,1.563 0.156,0.198 10 false B 0.979,1.74 1.135,1.938 0.156,0.198 10 false B 1.24,1.771 1.396,1.969 0.156,0.198 10 false B 1.5,1.771 1.656,1.969 0.156,0.198 10 false B 1.875,1.771 2.031,1.969 0.156,0.198 10 false B 2.24,1.719 2.396,1.917 0.156,0.198 10 false B

Install the No. 1 oil pan with the 14 bolts and 2 nuts.

Torque:
for bolt A : 10 N*m (102 kgf*cm, 7 ft.*lbf)
for bolt B and nut : 35 N*m (357 kgf*cm, 26 ft.*lbf)

Text in Illustration
V100135

Bolt
V100136

Nut

NOTICE:

Do not start the engine for at least 2 hours after installing the oil pan.



Hide 12102A 9.INSTALL NO. 2 OIL PAN SUB-ASSEMBLY

a.
A160730E04
0.896,0.854 1.281,0.26 1.281,0.26 1.406,0.26 false 1.458,0.177 1.771,0.375 0.313,0.198 10 false *1

Apply seal packing in a continuous line as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard seal diameter:

3.0 to 4.0 mm (0.118 to 0.156 in.)


Text in Illustration
*1 Seal Packing

NOTICE:
·

Remove any oil from the contact surface.

·

Install the No. 2 oil pan within 3 minutes and tighten the bolts and nuts within 15 minutes after applying seal packing.




b.
A274235

Install the No. 2 oil pan with the 14 bolts and 2 nuts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

Text in Illustration
V100135

Bolt
V100136

Nut

NOTICE:

Do not start the engine for at least 2 hours after installing the oil pan.



Hide 16877 10.INSTALL NO. 1 HEAT EXCHANGER COVER

a.
A214798E02
0.947,0.091 1.131,0.245 0.185,0.155 10 *1 1.154,0.178 1.258,0.178 1.258,0.178 1.368,0.685 false

Apply seal packing in a continuous line as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing 1282B, Three Bond 1282B or equivalent


Standard seal diameter:

3.0 to 4.0 mm (0.118 to 0.157 in.)


Text in Illustration
*1 Seal Packing

NOTICE:
·

Remove any oil from the contact surface.

·

Install the No. 1 heat exchanger cover within 3 minutes and tighten the bolts and nuts within 15 minutes after applying seal packing.




b.
U115456E03
0.292,0.292 0.417,0.438 0.125,0.146 10 false A 1.146,0.125 1.271,0.271 0.125,0.146 10 false A 1.75,0.125 1.875,0.271 0.125,0.146 10 false A 2.156,0.125 2.281,0.271 0.125,0.146 10 false A 2.854,0.167 2.979,0.313 0.125,0.146 10 false A 3.229,0.281 3.354,0.427 0.125,0.146 10 false A 3.01,1.74 3.135,1.885 0.125,0.146 10 false A 3.229,1.583 3.354,1.729 0.125,0.146 10 false C 2.01,1.865 2.135,2.01 0.125,0.146 10 false A 1.656,1.865 1.781,2.01 0.125,0.146 10 false A 1.021,1.865 1.146,2.01 0.125,0.146 10 false A 0.24,0.958 0.365,1.104 0.125,0.146 10 false B

Install the No. 1 heat exchanger cover with the 12 bolts and 2 nuts.

Torque:
for bolt C : 10 N*m (102 kgf*cm, 7 ft.*lbf)
for bolt A, bolt B and nut : 21 N*m (214 kgf*cm, 15 ft.*lbf)

Standard Bolt:
Item Length Thread Diameter
Bolt A 20 mm (0.787 in.) 8 mm (0.315 in.)
Bolt B 70 mm (2.76 in.) 8 mm (0.315 in.)
Bolt C 16 mm (0.630 in.) 6 mm (0.236 in.)


Text in Illustration
V100135

Bolt
V100136

Nut

NOTICE:

Do not start the engine for at least 2 hours after installing the heat exchanger cover.



Hide 12203A 11.INSTALL VENTILATION PIPE GASKET

a.
A220132E03
1.177,1.177 0.563,1.177 true 1.146,1.375 0.667,1.375 0.667,1.375 0.667,1.177 true 0.177,1.094 0.563,1.323 0.385,0.229 10 true SST

Using SST, evenly tap in a new ventilation pipe gasket until its surface is flush with the lip of the ventilation pipe.

SST
09950-60010  (09951-00360)
09950-70010  (09951-07100)

NOTICE:
·

Do not tap the ventilation pipe gasket at an angle.

·

Do not tap the ventilation pipe gasket excessively.




Hide 12258A 12.INSTALL OIL RETURN PIPE GASKET

a.
A217533

Install a new oil return pipe gasket.


Hide 11445 13.INSTALL CYLINDER BLOCK WATER JACKET SPACER

a.
A214628E02
0.398,0.313 0.583,0.467 0.185,0.155 10 *1 0.606,0.398 0.716,0.398 0.716,0.398 0.845,0.868 false 3.084,1.193 3.268,1.348 0.185,0.155 10 *1 3.046,1.283 2.936,1.283 2.936,1.283 2.515,0.813 false

Install the 2 cylinder block water jacket spacers as shown in the illustration.

Text in Illustration
*1 UP Mark

NOTICE:
·

Make sure that the cutouts indicated by the arrows in the illustration face away from the engine.

·

Make sure that the "up" marks are oriented as shown in the illustration.




Hide 11103C 22.INSTALL CAMSHAFT HOUSING SUB-ASSEMBLY RH

Hide 11104A 24.INSTALL CAMSHAFT HOUSING SUB-ASSEMBLY LH

Hide 13521A 25.INSTALL CRANKSHAFT TIMING GEAR KEY

a.
A214836

Install the crankshaft timing gear key.

HINT:

The other crankshaft timing gear key will be installed in a later step.



Hide 13550 26.INSTALL NO. 2 CHAIN TENSIONER ASSEMBLY

Hide 13561 28.INSTALL NO. 1 CHAIN VIBRATION DAMPER RH

Hide 13540 30.INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY RH

Hide 13560A 31.INSTALL NO. 3 CHAIN TENSIONER ASSEMBLY

Hide 13561 33.INSTALL NO. 1 CHAIN VIBRATION DAMPER LH

Hide 13540 35.INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY LH

Hide 13050 36.TIGHTEN CAMSHAFT TIMING GEAR ASSEMBLY

Hide 37.CHECK NO. 1 CYLINDER TO TDC/COMPRESSION

a.

Temporarily install the pulley set bolt.


b.

Rotate the crankshaft clockwise and check that the timing marks on the crankshaft timing gear and camshaft timing gears are as shown in the illustration.


c.

Remove the crankshaft pulley set bolt.

A214603E02
4.052,3.883 4.237,4.037 0.185,0.155 10 *1 0.202,0.417 0.387,0.572 0.185,0.155 10 *2 3.479,1.231 3.664,1.385 0.185,0.155 10 *a 0.163,2.868 0.348,3.023 0.185,0.155 10 *b 0.244,4.067 0.429,4.221 0.185,0.155 10 *c 0.371,0.492 0.45,0.492 0.45,0.492 0.558,0.889 false 1.307,0.319 1.492,0.474 0.185,0.155 10 *2 1.476,0.394 1.555,0.394 1.555,0.394 1.663,0.792 false 6.362,0.462 6.547,0.617 0.185,0.155 10 *2 6.531,0.537 6.611,0.537 6.611,0.537 6.718,0.934 false 5.226,0.341 5.410,0.496 0.185,0.155 10 *2 5.395,0.416 5.474,0.416 5.474,0.416 5.582,0.814 false 0.335,2.945 0.414,2.945 0.414,2.945 0.614,3.224 false 1.337,2.532 1.522,2.687 0.185,0.155 10 *b 1.507,2.607 1.586,2.607 1.586,2.607 1.737,3.161 false 6.16,2.653 6.345,2.808 0.185,0.155 10 *b 6.329,2.728 6.409,2.728 6.409,2.728 6.559,3.281 false 5.679,2.467 5.864,2.622 0.185,0.155 10 *b 5.669,2.544 5.59,2.544 5.59,2.544 5.445,3.221 false 0.327,4.067 0.327,4.005 0.327,4.005 0.538,3.392 false 0.887,4.162 1.072,4.316 0.185,0.155 10 *c 0.969,4.162 0.969,4.1 0.969,4.1 1.379,3.487 false 5.157,4.39 5.342,4.544 0.185,0.155 10 *c 5.24,4.39 5.24,4.328 5.24,4.328 5.451,3.715 false 6.814,4.183 6.999,4.337 0.185,0.155 10 *c 6.897,4.176 6.897,4.114 6.897,4.114 6.487,3.501 false 4.042,3.961 3.962,3.961 3.962,3.961 3.656,4.398 false 3.616,5.3 3.800,5.455 0.185,0.155 10 *2 3.698,5.29 3.698,5.228 3.698,5.228 3.487,4.813 false 0.69,4.896 0.875,5.051 0.185,0.155 10 *d 0.682,4.977 0.603,4.977 0.603,4.977 0.523,5.375 false 1.794,4.902 1.978,5.057 0.185,0.155 10 *e 1.785,4.975 1.706,4.975 1.706,4.975 1.597,5.22 false 1.766,4.691 1.951,4.846 0.185,0.155 10 *f 1.753,4.76 1.674,4.76 1.674,4.76 1.396,5.375 false 1.924,5.133 2.109,5.288 0.185,0.155 10 *a 0.687,6.29 0.872,6.444 0.185,0.155 10 *b 0.762,6.277 0.762,6.215 0.762,6.215 0.551,5.602 false 1.556,6.29 1.741,6.444 0.185,0.155 10 *b 1.632,6.277 1.632,6.215 1.632,6.215 1.42,5.602 false 6.784,4.896 6.980,5.068 0.196,0.172 10 *g 6.775,4.977 6.695,4.977 6.695,4.977 6.615,5.375 false 5.129,5.111 5.314,5.266 0.185,0.155 10 *a 5.206,4.881 5.391,5.036 0.185,0.155 10 *e 5.377,4.958 5.456,4.958 5.456,4.958 5.589,5.254 false 5.269,4.647 5.454,4.801 0.185,0.155 10 *h 5.44,4.724 5.52,4.724 5.52,4.724 5.812,5.379 false 5.522,6.287 5.707,6.442 0.185,0.155 10 *b 5.592,6.274 5.592,6.212 5.592,6.212 5.798,5.616 false 6.316,6.287 6.501,6.442 0.185,0.155 10 *b 6.387,6.274 6.387,6.212 6.387,6.212 6.592,5.616 false

Text in Illustration
*1 Crankshaft Timing Gear Key *2 Timing Mark
*a Toward Ceiling *b Timing Mark Position
*c Knock Pin Position *d Approximately 2°
*e Approximately 45° *f Approximately 16°
*g Approximately 18° *h Approximately 32°


Hide 11302 39.INSTALL TIMING CHAIN COVER SUB-ASSEMBLY

Hide 16100 40.INSTALL ENGINE WATER PUMP ASSEMBLY

Hide 11193 44.INSTALL SPARK PLUG TUBE GASKET

a.
A385818E01
0.531,1.896 1.146,2.094 0.615,0.198 10 false : *a

Using a cutter knife, cut off the seal part of the removed spark plug tube gasket.

Text in Illustration
*a Area to cut off


b.
A218898E01
1.826,0.379 2.010,0.534 0.185,0.155 10 *1 3.109,3.202 3.294,3.357 0.185,0.155 10 *2 3.109,3.465 3.294,3.620 0.185,0.155 10 *3 1.145,0.469 1.8,0.469 false 2.89,3.299 3.103,3.299 false 2.89,3.552 3.103,3.552 false

Using the removed spark plug tube gasket and a hammer, tap in a new spark plug tube gasket until it stops.

Text in Illustration
*1 Ventilation Baffle Plate Claw
*2 Removed Spark Plug Tube Gasket
*3 New Spark Plug Tube Gasket

HINT:

If the removed spark plug tube gasket does not fit on the new one, correct the removed one with pliers.



c.

Apply a light coat of MP grease to the spark plug tube gasket lip.


d.

Return the 4 ventilation baffle plate claws to their original positions.


Hide 15678D 45.INSTALL OIL CONTROL VALVE FILTER

a.

for Bank 1:

i.
A164313E17
2.885,0.146 2.99,0.146 2.99,0.146 3.125,0.875 true 2.198,0.146 2.313,0.146 2.313,0.146 2.823,0.781 true 2.417,1.115 2.417,1.052 2.417,1.052 2.49,0.875 false 2.677,0.063 2.865,0.281 0.188,0.219 10 true *1 2.323,1.125 2.51,1.281 0.188,0.156 10 false *3 1.99,0.063 2.177,0.219 0.188,0.156 10 false *2

Install the oil control valve filter to the cylinder head cover.

Text in Illustration
*1 Cylinder Head Cover Spacer
*2 New Gasket
*3 Oil Control Valve Filter


ii.

Install a new gasket and the cylinder head cover spacer with the 3 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)



b.

for Bank 2:

i.
A164314E14
0.635,0.135 0.521,0.135 0.521,0.135 0.313,0.76 true 1.281,0.135 1.177,0.135 1.177,0.135 0.625,0.667 true 0.969,0.99 0.969,0.75 false 0.656,0.031 0.927,0.26 0.271,0.229 10 true *1 0.865,1.01 1.052,1.167 0.188,0.156 10 false *3 1.323,0.021 1.51,0.177 0.188,0.156 10 false *2

Install the oil control valve filter to the cylinder head cover.

Text in Illustration
*1 Cylinder Head Cover Spacer
*2 New Gasket
*3 Oil Control Valve Filter


ii.

Install a new gasket and the cylinder head cover spacer with the 3 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)



Hide 11201 46.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY RH

Hide 11202 47.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY LH

Hide 16355 48.INSTALL FRONT WATER BY-PASS JOINT

Hide 11415 50.INSTALL CYLINDER BLOCK WATER DRAIN COCK SUB-ASSEMBLY

a.

Apply adhesive to 2 or 3 threads of the cylinder block water drain cocks.

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent



b.

Install the cylinder block water drain cocks.

Torque:
30 N*m (306 kgf*cm, 22 ft.*lbf)

A385819E01
0.469,0.219 0.781,0.417 0.313,0.198 10 false *A 3.979,0.219 4.292,0.417 0.313,0.198 10 false *B 0.781,1.542 1.094,1.74 0.313,0.198 10 false *a 1.354,1.708 1.667,1.906 0.313,0.198 10 false 30° 1.667,2.042 1.979,2.24 0.313,0.198 10 false 30° 1.646,2.333 1.958,2.531 0.313,0.198 10 false 50° 6.208,1.865 6.521,2.063 0.313,0.198 10 false *a 4.75,1.771 5.063,1.969 0.313,0.198 10 false 30° 5.094,2.115 5.406,2.313 0.313,0.198 10 false 30° 5.021,2.375 5.333,2.573 0.313,0.198 10 false 50°

Text in Illustration
*A for Bank 1
*B for Bank 2
*a Front


c.

Tighten the cylinder block water drain cocks up to an additional 360° so that the cylinder block water drain cock pipes are within the range shown in the illustration.

NOTICE:
·

Do not rotate the cylinder block water drain cocks more than 1 revolution (360°) after tightening the cylinder block water drain cocks to the specified torque.

·

Do not loosen the cylinder block water drain cocks to adjust them. If an adjustment is necessary, remove the cylinder block water drain cocks and reinstall them.




d.

Install the water drain cock plugs to the water drain cocks.

Torque:
13 N*m (130 kgf*cm, 9 ft.*lbf)


Hide 15330B 51.INSTALL CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY

a.

for Bank 1:

i.

Apply a light coat of engine oil to 2 new O-rings.


ii.

Install the 2 O-rings to the 2 camshaft timing oil control valves.


iii.

Install the 2 camshaft timing oil control valves with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)



b.

for Bank 2:

i.

Apply a light coat of engine oil to 2 new O-rings.


ii.

Install the 2 O-rings to the 2 camshaft timing oil control valves.


iii.

Install the 2 camshaft timing oil control valves with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)



Hide 12185 58.INSTALL OIL FILLER CAP HOUSING

a.
A161917E01
1.616,0.069 1.801,0.224 0.185,0.155 10 *1 1.338,0.454 1.487,0.163 1.487,0.163 1.601,0.163 false 2.53,0.558 2.715,0.713 0.185,0.155 10 *2 2.252,0.943 2.401,0.652 2.401,0.652 2.515,0.652 false

Align the protrusion of a new gasket with the cutout of the oil filler cap housing and install the gasket to the oil filler cap housing.

Text in Illustration
*1 Cutout
*2 Protrusion


b.

Install the oil filler cap housing with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 12108 59.INSTALL OIL FILLER CAP SUB-ASSEMBLY

a.

Install the gasket to the oil filler cap.


b.

Install the oil filler cap.


Hide 15609 61.INSTALL OIL FILTER BRACKET SUB-ASSEMBLY

Hide 83520 62.INSTALL OIL PRESSURE SENDER GAUGE ASSEMBLY