Home › Engine / Hybrid System › 1UR-FE (ENGINE MECHANICAL) › CYLINDER HEAD GASKET › 2014.08–2016.08
RM2660E _51 Engine / Hybrid System _052776 1UR-FE ENGINE MECHANICAL _0255036 CYLINDER HEAD GASKET A

1UR-FE ENGINE MECHANICAL  CYLINDER HEAD GASKET  INSTALLATION  


PROCEDURE

Hide 11116 1.INSTALL NO. 2 CYLINDER HEAD GASKET

a.
A228408E01
3.19,1.607 3.375,1.762 0.185,0.155 10 *1 3.27,1.576 3.27,1.486 3.27,1.486 3.074,1.018 false

Place a new cylinder head gasket on the cylinder block surface with the front face of the Lot No. stamp upward.

Text in Illustration
*1 Lot No.
V100135

Engine Front

NOTICE:
·

Make sure that the gasket is installed facing the proper direction.

·

Make sure that no oil is on the front end (indicated by the arrows) of the No. 2 cylinder head gasket.




Hide 11102 2.INSTALL CYLINDER HEAD SUB-ASSEMBLY LH

a.

Place the cylinder head on the cylinder block.

NOTICE:
·

Make sure that no oil is on the mounting surface of the cylinder head.

·

Place the cylinder head gently in order not to damage the gasket with the bottom part of the head.




b.

Install the cylinder head bolts.

HINT:

The cylinder head bolts are tightened in 3 progressive steps.


i.

Apply a light coat of engine oil to the threads and under the heads of the cylinder head bolts.


ii.
U115351E03
1.615,1.875 1.792,2.063 0.177,0.188 10 false 1 1.635,0.25 1.76,0.396 0.125,0.146 10 false 2 1.073,1.885 1.24,2.073 0.167,0.188 10 false 3 2.177,0.25 2.302,0.396 0.125,0.146 10 false 4 1.083,0.26 1.208,0.406 0.125,0.146 10 false 5 2.188,1.875 2.354,2.063 0.167,0.188 10 false 6 0.531,0.25 0.646,0.385 0.115,0.135 10 false 7 2.688,0.25 2.948,0.438 0.26,0.188 10 false 10 2.927,1.75 3.052,1.927 0.125,0.177 10 false 8 0.521,1.875 0.656,2.021 0.135,0.146 10 false 9

Step 1:

Using a 10 mm bi-hexagon wrench, install and uniformly tighten the 10 cylinder head bolts with the plate washers in several steps in the sequence shown in the illustration.

Torque:
36 N*m (367 kgf*cm, 27 ft.*lbf)


iii.

Mark the front side of each cylinder head bolt head with paint.


iv.

Step 2:

Tighten the cylinder head bolts 90°.


v.

Step 3:

Tighten the cylinder head bolts an additional 90°.


vi.

Check that the paint marks are now at a 180° angle to the front.


vii.
U115349E03
3.146,0.135 3.271,0.281 0.125,0.146 10 false 1 3.24,0.615 3.365,0.76 0.125,0.146 10 false 2

Install and uniformly tighten the 2 bolts in the sequence shown in the illustration.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)

NOTICE:

Thoroughly wipe clean any seal packing.




Hide 11115 3.INSTALL CYLINDER HEAD GASKET

a.
A228409E01
0.232,1.785 0.417,1.939 0.185,0.155 10 *1 0.323,1.355 0.323,1.77 false

Place a new cylinder head gasket on the cylinder block surface with the front face of the Lot No. stamp upward.

Text in Illustration
*1 Lot No.
V100135

Engine Front

NOTICE:
·

Make sure that the gasket is installed facing the proper direction.

·

Make sure that no oil is on the front end (indicated by the arrows) of the cylinder head gasket.




Hide 11101 4.INSTALL CYLINDER HEAD SUB-ASSEMBLY

a.

Place the cylinder head on the cylinder block.

NOTICE:
·

Place the cylinder head gently in order not to damage the gasket with the bottom part of the head.

·

Make sure that no oil is on the mounting surface of the cylinder head.




b.

Install the cylinder head bolts.

HINT:

The cylinder head bolts are tightened in 3 progressive steps.


i.

Apply a light coat of engine oil to the threads and under the heads of the cylinder head bolts.


ii.
U115355E03
1.635,1.792 1.792,2.021 0.156,0.229 10 false 1 1.625,0.208 1.75,0.354 0.125,0.146 10 false 2 2.188,1.802 2.354,1.99 0.167,0.188 10 false 3 1.125,0.208 1.25,0.354 0.125,0.146 10 false 4 2.156,0.219 2.281,0.365 0.125,0.146 10 false 5 1.104,1.802 1.281,1.979 0.177,0.177 10 false 6 2.698,0.208 2.813,0.344 0.115,0.135 10 false 7 0.573,0.208 0.771,0.354 0.198,0.146 10 false 10 0.563,1.802 0.729,1.99 0.167,0.188 10 false 8 2.885,1.667 3.052,1.927 0.167,0.26 10 false 9

Step 1:

Using a 10 mm bi-hexagon wrench, install and uniformly tighten the 10 cylinder head bolts with the plate washers in several steps in the sequence shown in the illustration.

Torque:
36 N*m (367 kgf*cm, 27 ft.*lbf)


iii.

Mark the front side of each cylinder head bolt head with paint.


iv.

Step 2:

Tighten the cylinder head bolts 90°.


v.

Step 3:

Tighten the cylinder head bolts an additional 90°.


vi.

Check that the paint marks are now at a 180° angle to the front.


vii.
U115353E03
0.406,0.573 0.531,0.719 0.125,0.146 10 false 1 0.375,1.26 0.5,1.406 0.125,0.146 10 false 2

Install and uniformly tighten the 2 bolts in the sequence shown in the illustration.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)

NOTICE:

Thoroughly wipe clean any seal packing.




Hide 13716 5.INSTALL VALVE STEM CAP

a.

Apply a light coat of engine oil to the valve stem caps.


b.

Install the 32 valve stem caps to the cylinder head.


Hide 13750 6.INSTALL VALVE LASH ADJUSTER ASSEMBLY

a.

b.

Install the 32 valve lash adjusters to the cylinder head.

NOTICE:

Install each valve lash adjuster to the same place it was removed from.



Hide 13801 7.INSTALL NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

a.

Apply engine oil to the valve lash adjuster tips and valve stem cap ends.


b.
A163454E03
0.842,0.136 1.027,0.291 0.185,0.155 10 *1 0.412,0.991 0.597,1.146 0.185,0.155 10 *2 2.952,0.998 3.137,1.153 0.185,0.155 10 *3 2.517,1.085 2.932,1.085 false 0.627,1.085 1.041,1.085 false 1.05,0.224 1.159,0.224 1.159,0.224 1.381,0.549 false

Install the 32 No. 1 valve rocker arms as shown in the illustration.

Text in Illustration
*1 No. 1 Valve Rocker Arm
*2 Valve Stem Cap
*3 Valve Lash Adjuster


Hide 13053 8.INSTALL CAMSHAFT SUB-ASSEMBLY

Hide 17140 9.INSTALL EXHAUST MANIFOLD ASSEMBLY