Home › Engine / Hybrid System › 1VD-FTV (ENGINE MECHANICAL) › ENGINE › from 2015.08
RM2660E _51 Engine / Hybrid System _052779 1VD-FTV ENGINE MECHANICAL _0255063 ENGINE G

1VD-FTV ENGINE MECHANICAL  ENGINE  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 1.INSPECT ENGINE IDLE SPEED

NOTICE:
·

Turn all the electrical systems and the A/C off.

·

When checking the idle speed, move the shift lever to neutral.



HINT:
·

For more information about the GTS, refer to its operator's manual.

·

If an GTS is not available, use a tachometer tester probe as a substitute.



a.

When using the GTS:

i.

Warm up the engine.


ii.

Connect the GTS to the DLC3.


iii.

Enter the following menus:

Powertrain / Engine / Data List / Engine Speed.

HINT:

Refer to the GTS operator's manual for help selecting the Data List.



iv.

Inspect the engine idle speed.

Standard Idle Speed:
Item Specified Condition
for Automatic Transmission 550 to 750 rpm
for Manual Transmission 500 to 600 rpm



v.

Disconnect the GTS from the DLC3.



b.

When not using the GTS:

i.

Warm up and stop the engine.


ii.
A167780E02
0.117,1.315 0.411,1.457 0.295,0.142 10 TAC 0.98,1.396 0.494,1.396 false 0.096,0.083 0.281,0.238 0.185,0.155 10 *a

Connect a tester probe of a tachometer to terminal 9 (TAC) of the DLC3 with SST.

SST
09843-18040  

Text in Illustration
*a Front view of DLC3


iii.

Inspect the engine idle speed.

Standard Idle Speed:
Item Specified Condition
for Automatic Transmission 550 to 750 rpm
for Manual Transmission 500 to 600 rpm



iv.

Disconnect the tester probe from terminal 9 (TAC) of the DLC3.



Hide 2.INSPECT MAXIMUM ENGINE SPEED

a.

Start the engine.


b.

Fully depress the accelerator pedal.


c.

Check the maximum engine speed.

Maximum engine speed:

4700 to 4900 rpm



Hide 3.INSPECT COMPRESSION

a.

Warm up and stop the engine.


b.

Disconnect the cable from the negative (-) battery terminal.


c.

Remove the No. 1 glow plug connector.

i.

w/ Intercooler:

Remove the intercooler assembly (See page Engine / Hybrid System>1VD-FTV (INTAKE / EXHAUST)>INTERCOOLER>REMOVAL).


ii.

Remove the injection pipes (See page Engine / Hybrid System>1VD-FTV (FUEL)>COMMON RAIL>REMOVAL).


iii.

Remove the No. 1 glow plug connector.


iv.

Reinstall the injection pipes (See page Engine / Hybrid System>1VD-FTV (FUEL)>COMMON RAIL>INSTALLATION).



d.

e.

Disconnect all connectors from the 8 injectors.


f.

Connect the cable to the negative (-) battery terminal.


g.

Inspect the cylinder compression pressure.

i.
A177330E02
1.722,0.136 2.82,0.136 false 1.006,0.619 1.181,0.619 1.181,0.619 1.981,1.502 false 1.514,0.048 1.698,0.202 0.185,0.155 10 *1 0.795,0.529 0.980,0.683 0.185,0.155 10 *2

Insert SST (attachment) into the glow plug hole.

SST
09992-00026  (09992-00410, 09992-00211)

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)

Text in Illustration
*1 SST (Compression Gauge)
*2 SST (Attachment)


ii.

Connect SST (compression gauge) to SST (attachment).


iii.

While cranking the engine, measure the compression pressure.

Standard compression pressure (normal condition):

2700 kPa (27.5 kgf/cm2, 392 psi)


Minimum compression pressure:

2200 kPa (22.4 kgf/cm2, 319 psi)


Difference between each cylinder:

500 kPa (5.1 kgf/cm2, 73 psi) or less


NOTICE:
·

Use a fully-charged battery so the engine speed can be increased to 280 rpm or more.

·

Inspect the other cylinders in the same way.

·

Measure the compression as quickly as possible.




iv.

If the cylinder compression is low, pour a small amount of engine oil into the cylinder through the glow plug holes. Then inspect the cylinder compression again.

If adding oil increases the compression pressure, the piston rings and/or cylinder bore may be worn or damaged.

If the pressure stays low, the valve may be stuck or seated improperly, or there may be leakage from the gasket.


v.

Remove SST (attachment and compression gauge).



h.

Disconnect the cable from the negative (-) battery terminal.


i.

Connect all connectors to the 8 injectors.



k.

Install the No. 1 glow plug connector.

i.

Remove the injection pipes (See page Engine / Hybrid System>1VD-FTV (FUEL)>COMMON RAIL>REMOVAL).


ii.

Reinstall the No. 1 glow plug connector.


iii.

Install the injection pipes (See page Engine / Hybrid System>1VD-FTV (FUEL)>COMMON RAIL>INSTALLATION).


iv.

w/ Intercooler:

Install the intercooler assembly (See page Engine / Hybrid System>1VD-FTV (INTAKE / EXHAUST)>INTERCOOLER>INSTALLATION).