Home › Engine / Hybrid System › 1VD-FTV (ENGINE MECHANICAL) › ENGINE UNIT
RM2660E _51 Engine / Hybrid System _052779 1VD-FTV ENGINE MECHANICAL _0255065 ENGINE UNIT G

1VD-FTV ENGINE MECHANICAL  ENGINE UNIT  INSPECTION  


PROCEDURE

Hide 11101 1.CLEAN CYLINDER HEAD SUB-ASSEMBLY

a.
A164825

Using a gasket scraper, remove all the gasket material from the cylinder block contact surface.

NOTICE:

Be careful not to scratch the cylinder block contact surface.



b.
A164826

Using a wire brush, remove all the carbon from the combustion chambers.

NOTICE:

Be careful not to damage the combustion chambers and valve seats.



c.
A164841

Using a valve guide bushing brush and solvent, clean all the valve guide bushes.


d.
A164827

Using a soft brush and solvent, thoroughly clean the cylinder head.


Hide 11101 2.INSPECT CYLINDER HEAD SUB-ASSEMBLY

a.

Using a precision straightedge and feeler gauge, measure the warpage of the contact surface between the cylinder head and cylinder block, and the cylinder head and manifolds.

A385800E01
0.125,1.458 1.406,1.635 1.281,0.177 10 false Cylinder Block Side: 4.135,0.271 5.677,0.469 1.542,0.198 10 false Exhaust Manifold Side: 4.135,1.51 5.719,1.708 1.583,0.198 10 false Intake Manifold Side:

Standard Warpage:
Item Specified Condition
Cylinder block side 0 to 0.05 mm (0 to 0.00197 in.)
Intake manifold side 0 to 0.08 mm (0 to 0.00315 in.)
Exhaust manifold side 0 to 0.08 mm (0 to 0.00315 in.)


Maximum Warpage:
Item Specified Condition
Cylinder block side 0.05 mm (0.00197 in.)
Intake manifold side 0.08 mm (0.00315 in.)
Exhaust manifold side 0.08 mm (0.00315 in.)


If the warpage is more than the maximum, replace the cylinder head sub-assembly.


b.
A075610

Using a dye penetrant, check the intake ports, exhaust ports and cylinder surface for cracks.

If there are cracks, replace the cylinder head sub-assembly.


Hide 11101A 3.INSPECT CYLINDER HEAD BOLT

a.
A184036E01
0.157,1.755 1.182,1.917 1.024,0.162 10 Measuring Area

Using a vernier caliper, measure the outside thread diameter of the bolt.

Standard diameter:

12.8 to 13.0 mm (0.504 to 0.512 in.)


Minimum diameter:

12.5 mm (0.492 in.)


HINT:

If a visual check reveals no excessively thin areas, check the center of the bolt (see illustration) and find the area that has the smallest diameter.


If the diameter is less than the minimum, replace the cylinder head bolt.


Hide 4.INSPECT NO. 2 AND NO. 3 CAMSHAFT THRUST CLEARANCE (for Intake Camshaft)

a.

Install the No. 2 and No. 5 camshaft bearing caps to the cylinder head.


b.

Place the camshafts on the cylinder head.


c.
A164896

Temporarily install the No. 1 and No. 4 camshaft bearing caps with the 4 bolts by hand.

NOTICE:

Do not turn the camshafts.



d.

Install the No. 3 camshaft bearing caps.

i.
A164898E01
0.066,0.063 0.331,0.229 0.266,0.166 10 RH: 0.066,2.552 0.331,2.719 0.266,0.166 10 LH:

Confirm the marks and numbers on the camshaft bearing caps and place them in their proper position and direction.


ii.

Temporarily install the 16 bolts.



e.
U162927E02
1.583,3.708 1.74,3.875 0.156,0.167 10 false 1 0.104,2.76 0.281,2.927 0.177,0.167 10 false 10 1.594,2.5 1.75,2.667 0.156,0.167 10 false 2 0.104,3.854 0.281,4.021 0.177,0.167 10 false 11 2.198,3.719 2.354,3.896 0.156,0.177 10 false 3 0.104,4.302 0.281,4.469 0.177,0.167 10 false 12 2.198,2.5 2.354,2.667 0.156,0.167 10 false 4 0.99,3.708 1.146,3.875 0.156,0.167 10 false 5 0.99,2.5 1.146,2.667 0.156,0.167 10 false 6 2.813,3.719 2.969,3.885 0.156,0.167 10 false 7 2.802,2.5 2.958,2.667 0.156,0.167 10 false 8 0.146,3.177 0.302,3.344 0.156,0.167 10 false 9 0.031,0 0.323,0.167 0.292,0.167 10 false RH: 0.031,2.26 0.323,2.427 0.292,0.167 10 false LH: 1.5,0.75 1.656,0.917 0.156,0.167 10 false 1 0.146,1.802 0.323,1.969 0.177,0.167 10 false 10 1.49,1.99 1.646,2.156 0.156,0.167 10 false 2 0.146,0.833 0.323,1 0.177,0.167 10 false 11 2.094,0.75 2.25,0.927 0.156,0.177 10 false 3 0.135,0.375 0.313,0.542 0.177,0.167 10 false 12 2.094,1.979 2.25,2.146 0.156,0.167 10 false 4 0.896,0.74 1.052,0.906 0.156,0.167 10 false 5 0.906,1.99 1.063,2.156 0.156,0.167 10 false 6 2.698,0.75 2.854,0.917 0.156,0.167 10 false 7 2.698,1.99 2.854,2.156 0.156,0.167 10 false 8 0.177,1.354 0.333,1.521 0.156,0.167 10 false 9

Uniformly tighten the 24 bolts in several steps in the order shown in the illustration.

Torque:
for 12 mm head bolt of No. 1 and No. 4 camshaft bearing cap : 21 N*m (214 kgf*cm, 15 ft.*lbf)
for 10 mm head bolt of No. 3 camshaft bearing cap : 10 N*m (102 kgf*cm, 7 ft.*lbf)


f.
A164551

Using a dial indicator, measure the thrust clearance while moving the camshaft back and forth.

Standard thrust clearance:

0.035 to 0.160 mm (0.00138 to 0.00630 in.)


Maximum thrust clearance:

0.180 mm (0.00709 in.)


If the thrust clearance is more than the maximum, replace the camshaft.

If necessary, replace the cylinder head sub-assembly.


Hide 5.INSPECT NO. 1 AND NO. 4 CAMSHAFT THRUST CLEARANCE (for Exhaust Camshaft)

a.

Install the No. 2 and No. 5 camshaft bearing caps to the cylinder head.


b.

Place the camshafts on the cylinder head.


c.
A164958

Temporarily install the No. 1 and No. 4 camshaft bearing caps with the 4 bolts by hand.

NOTICE:

Do not turn the camshafts.



d.

Install the No. 3 camshaft bearing caps.

i.
A164959E01
0.127,0.057 0.428,0.236 0.300,0.180 10 RH: 0.127,2.402 0.428,2.581 0.300,0.180 10 LH:

Confirm the marks and numbers on the camshaft bearing caps and place them in their proper position and direction.


ii.

Temporarily install the 16 bolts.



e.
U162930E02
1.625,2.979 1.781,3.146 0.156,0.167 10 false 1 0.083,4.208 0.26,4.375 0.177,0.167 10 false 10 1.635,4.24 1.792,4.406 0.156,0.167 10 false 2 0.083,3.042 0.26,3.208 0.177,0.167 10 false 11 2.229,2.979 2.385,3.156 0.156,0.177 10 false 3 0.083,2.604 0.26,2.771 0.177,0.167 10 false 12 2.229,4.24 2.385,4.417 0.156,0.177 10 false 4 1.063,2.979 1.219,3.146 0.156,0.167 10 false 5 1.063,4.25 1.219,4.417 0.156,0.167 10 false 6 2.802,2.99 2.958,3.156 0.156,0.167 10 false 7 2.802,4.24 2.958,4.406 0.156,0.167 10 false 8 0.115,3.698 0.271,3.865 0.156,0.167 10 false 9 0.063,0 0.354,0.167 0.292,0.167 10 false RH: 0.063,2.292 0.354,2.458 0.292,0.167 10 false LH: 1.49,1.573 1.646,1.74 0.156,0.167 10 false 1 0.188,0.438 0.365,0.604 0.177,0.167 10 false 10 1.49,0.344 1.646,0.51 0.156,0.167 10 false 2 0.198,1.646 0.375,1.813 0.177,0.167 10 false 11 2.104,1.573 2.26,1.75 0.156,0.177 10 false 3 0.188,2.031 0.365,2.198 0.177,0.167 10 false 12 2.104,0.344 2.26,0.51 0.156,0.167 10 false 4 0.906,1.573 1.063,1.74 0.156,0.167 10 false 5 0.906,0.344 1.063,0.51 0.156,0.167 10 false 6 2.698,1.583 2.854,1.75 0.156,0.167 10 false 7 2.698,0.344 2.854,0.51 0.156,0.167 10 false 8 0.219,1.063 0.375,1.229 0.156,0.167 10 false 9

Uniformly tighten the 24 bolts in several steps in the order shown in the illustration.

Torque:
for 12 mm head bolt of No. 1 and No. 4 camshaft bearing cap : 21 N*m (214 kgf*cm, 15 ft.*lbf)
for 10 mm head bolt of No. 3 camshaft bearing cap : 10 N*m (102 kgf*cm, 7 ft.*lbf)


f.
A164550

Using a dial indicator, measure the thrust clearance while moving the camshaft back and forth.

Standard thrust clearance:

0.035 to 0.160 mm (0.00138 to 0.00630 in.)


Maximum thrust clearance:

0.180 mm (0.00709 in.)


If the thrust clearance is more than the maximum, replace the camshafts.

If necessary, replace the cylinder head sub-assembly.


Hide 13511 6.INSPECT CAMSHAFT

a.
A164552

Inspect the camshaft for runout.

i.

Place the camshaft on V-blocks.


ii.

Using a dial indicator, measure the runout at the center journal.

Maximum runout:

0.03 mm (0.00118 in.)


If the runout is more than the maximum, replace the camshaft.



b.
A164553

Inspect the cam lobe height.

i.

Using a micrometer, measure the cam lobe height.

Standard Cam Lobe Height:
Item Specified Condition
No. 2 and No. 3 camshaft
(intake)
37.277 to 37.387 mm (1.468 to 1.472 in.)
No. 1 and No. 4 camshaft
(exhaust)
38.324 to 38.434 mm (1.509 to 1.513 in.)


Minimum Cam Lobe Height:
Item Specified Condition
No. 2 and No. 3 camshaft
(intake)
37.277 mm (1.468 in.)
No. 1 and No. 4 camshaft
(exhaust)
38.324 mm (1.509 in.)


If the cam lobe height is less than the minimum, replace the camshaft.



c.
A385802E01
0.688,3.844 0.688,3.031 false 1.542,3.292 2.865,3.292 2.865,3.292 3,3.115 false 1.552,3.292 1.125,3.292 1.125,3.292 1,3.115 false 1.969,3.542 1.969,3.292 false 1.573,3.604 2.448,3.813 0.875,0.208 10 false Other Journal 0.323,3.917 1.198,4.125 0.875,0.208 10 false No. 1 Journal

Inspect the camshaft journal diameter.

i.

Using a micrometer, measure the journal diameter.

Standard Journal Diameter:
Item Specified Condition
No. 1 journal 29.969 to 29.985 mm (1.180 to 1.181 in.)
Other journal 26.969 to 26.985 mm (1.0618 to 1.0624 in.)


If the journal diameter is not as specified, check the oil clearance.



Hide 7.INSPECT CAMSHAFT OIL CLEARANCE

a.

Clean the camshaft bearing caps and camshaft journals.


b.

Place the camshafts on the cylinder head.


c.
A164829

Lay a strip of Plastigage across each of the camshaft journals.


d.
A168291E01
0.085,0.024 0.376,0.199 0.290,0.176 10 RH: 0.085,2.378 0.376,2.554 0.290,0.176 10 LH:

Temporarily install the camshaft bearing cap with the 4 bolts by hand.

NOTICE:

Do not turn the camshafts.



e.

Install the No. 3 camshaft bearing caps with the 16 bolts.

i.

Confirm the marks and numbers on the camshaft bearing caps and place them in their proper position and direction.

A385803


ii.

Temporarily install the 16 bolts.



f.
U162955E02
1.802,1.438 1.958,1.604 0.156,0.167 10 false 1 0.781,2.135 0.958,2.302 0.177,0.167 10 false 10 1.417,2.135 1.573,2.302 0.156,0.167 10 false 2 1.156,1.083 1.333,1.25 0.177,0.167 10 false 11 1.813,1.073 1.969,1.24 0.156,0.167 10 false 3 0.74,0.417 0.917,0.583 0.177,0.167 10 false 12 1.396,0.406 1.552,0.573 0.156,0.167 10 false 4 3.052,1.438 3.229,1.604 0.177,0.167 10 false 13 2.406,1.448 2.563,1.615 0.156,0.167 10 false 5 3.052,1.708 3.229,1.875 0.177,0.167 10 false 14 2.021,2.135 2.177,2.302 0.156,0.167 10 false 6 3.052,1.073 3.229,1.24 0.177,0.167 10 false 15 2.406,1.083 2.563,1.25 0.156,0.167 10 false 7 3.052,0.802 3.229,0.969 0.177,0.167 10 false 16 2.031,0.406 2.188,0.573 0.156,0.167 10 false 8 0.135,1.656 0.313,1.823 0.177,0.167 10 false 17 1.198,1.448 1.354,1.615 0.156,0.167 10 false 9 0.229,2.073 0.406,2.24 0.177,0.167 10 false 18 0.125,0.875 0.302,1.042 0.177,0.167 10 false 19 0.135,0.417 0.313,0.583 0.177,0.167 10 false 20 1.969,3.729 2.125,3.906 0.156,0.177 10 false 1 0.906,4.385 1.083,4.563 0.177,0.177 10 false 10 1.573,4.385 1.729,4.563 0.156,0.177 10 false 2 1.313,3.365 1.49,3.531 0.177,0.167 10 false 11 1.979,3.375 2.135,3.552 0.156,0.177 10 false 3 0.896,2.698 1.073,2.865 0.177,0.167 10 false 12 1.573,2.698 1.729,2.865 0.156,0.167 10 false 4 3.198,3.729 3.375,3.906 0.177,0.177 10 false 13 2.604,3.729 2.76,3.906 0.156,0.177 10 false 5 3.198,3.99 3.375,4.167 0.177,0.177 10 false 14 2.219,4.396 2.375,4.573 0.156,0.177 10 false 6 3.198,3.365 3.375,3.531 0.177,0.167 10 false 15 2.604,3.375 2.76,3.542 0.156,0.167 10 false 7 3.188,3.094 3.365,3.26 0.177,0.167 10 false 16 2.219,2.698 2.375,2.865 0.156,0.167 10 false 8 0.073,3.948 0.25,4.125 0.177,0.177 10 false 17 1.354,3.729 1.51,3.906 0.156,0.177 10 false 9 0.146,4.375 0.323,4.552 0.177,0.177 10 false 18 0.073,3.156 0.25,3.323 0.177,0.167 10 false 19 0.083,2.708 0.26,2.875 0.177,0.167 10 false 20 0.083,2.271 0.344,2.427 0.26,0.156 10 false LH: 0.083,0 0.344,0.156 0.26,0.156 10 false RH:

Uniformly tighten the 20 bolts in several steps in the order shown in the illustration.

Torque:
for 12 mm head bolt of No. 1 and No. 4 camshaft bearing cap : 21 N*m (214 kgf*cm, 15 ft.*lbf)
for 10 mm head bolt of No. 3 camshaft bearing cap : 10 N*m (102 kgf*cm, 7 ft.*lbf)


g.
U162956E02
0.104,2.729 0.26,2.896 0.156,0.167 10 false 1 1.313,3.354 1.49,3.521 0.177,0.167 10 false 10 0.115,3.156 0.271,3.323 0.156,0.167 10 false 2 0.917,4.385 1.094,4.552 0.177,0.167 10 false 11 0.208,4.385 0.365,4.552 0.156,0.167 10 false 3 1.313,3.719 1.49,3.885 0.177,0.167 10 false 12 0.104,3.938 0.26,4.104 0.156,0.167 10 false 4 2.177,2.667 2.354,2.833 0.177,0.167 10 false 13 3.229,3.104 3.385,3.271 0.156,0.167 10 false 5 2.573,3.354 2.75,3.521 0.177,0.167 10 false 14 3.229,3.354 3.385,3.521 0.156,0.167 10 false 6 2.167,4.385 2.344,4.552 0.177,0.167 10 false 15 3.229,3.979 3.385,4.146 0.156,0.167 10 false 7 2.563,3.729 2.74,3.896 0.177,0.167 10 false 16 3.229,3.729 3.385,3.896 0.156,0.167 10 false 8 1.531,2.667 1.708,2.833 0.177,0.167 10 false 17 0.948,2.667 1.104,2.833 0.156,0.167 10 false 9 1.938,3.365 2.115,3.531 0.177,0.167 10 false 18 1.542,4.385 1.719,4.552 0.177,0.167 10 false 19 1.938,3.729 2.115,3.896 0.177,0.167 10 false 20 0.208,0.375 0.365,0.542 0.156,0.167 10 false 1 1.177,1.083 1.354,1.25 0.177,0.167 10 false 10 0.208,0.885 0.365,1.052 0.156,0.167 10 false 2 0.781,2.094 0.958,2.26 0.177,0.167 10 false 11 0.219,2.01 0.375,2.177 0.156,0.167 10 false 3 1.167,1.438 1.344,1.604 0.177,0.167 10 false 12 0.219,1.625 0.375,1.792 0.156,0.167 10 false 4 2,0.417 2.177,0.583 0.177,0.167 10 false 13 3.052,0.833 3.208,1 0.156,0.167 10 false 5 2.385,1.083 2.563,1.25 0.177,0.167 10 false 14 3.052,1.073 3.208,1.24 0.156,0.167 10 false 6 1.969,2.094 2.146,2.26 0.177,0.167 10 false 15 3.063,1.667 3.219,1.833 0.156,0.167 10 false 7 2.385,1.438 2.563,1.604 0.177,0.167 10 false 16 3.052,1.438 3.208,1.604 0.156,0.167 10 false 8 1.354,0.417 1.531,0.583 0.177,0.167 10 false 17 0.781,0.417 0.938,0.583 0.156,0.167 10 false 9 1.771,1.063 1.948,1.229 0.177,0.167 10 false 18 1.375,2.094 1.552,2.26 0.177,0.167 10 false 19 1.781,1.438 1.958,1.604 0.177,0.167 10 false 20 0.125,0 0.396,0.177 0.271,0.177 10 false RH: 0.125,2.313 0.396,2.49 0.271,0.177 10 false LH:

Uniformly loosen and remove the 20 bolts in the sequence shown in the illustration.


h.
A164830

Measure the Plastigage at its widest point.

Standard oil clearance:

0.025 to 0.062 mm (0.000984 to 0.00244 in.)


Maximum oil clearance:

0.072 mm (0.00283 in.)


If the oil clearance is more than the maximum, replace the camshaft.

If necessary, replace the cylinder head sub-assembly.


i.

Remove the Plastigage completely.


j.

Remove the camshafts.


Hide 13801 8.INSPECT VALVE ROCKER ARM SUB-ASSEMBLY

a.
A164592

Turn the roller by hand to check that it turns smoothly.

If the roller does not turn smoothly, replace the valve rocker arm.


Hide 13750 9.INSPECT VALVE LASH ADJUSTER ASSEMBLY

NOTICE:
·

Keep the adjuster free from dirt and foreign objects.

·

Use only clean engine oil.



a.

Place the lash adjuster into a container full of new engine oil.


b.

Insert SST tip into the lash adjuster plunger and use the tip to press down on the check ball inside the plunger.

SST
09276-75010  


c.

Squeeze SST and the lash adjuster together to move the plunger up and down 5 to 6 times.


d.

Check the movement of the plunger and bleed air.

OK:

Plunger moves up and down.


NOTICE:

When bleeding high-pressure air from the compression chamber, make sure that the tip of SST is actually pressing the check ball as shown in the illustration. If the check ball is not pressed, air will not bleed.


U121308E02
0.729,0.729 0.958,0.729 false 1.76,1.833 2.333,1.833 true 0.625,1.083 1.01,1.083 true 0.615,1.271 1.021,1.271 false 0.51,1.813 1.01,1.813 true 1.01,2.354 0.573,2.354 true 0.51,2.156 1.01,2.156 true 1.865,2.167 2.365,2.167 true 5.625,1.729 4.656,2.25 4.656,2.25 4.656,2.344 true 1.01,0.656 1.323,0.823 0.313,0.167 10 false SST 3.146,0.083 3.823,0.302 0.677,0.219 10 false Taper Part 3.146,0.458 3.667,0.646 0.521,0.188 10 false Plunger 3.146,0.844 4.771,1 1.625,0.156 10 false Lower Pressure Chamber 0.135,0.135 0.844,0.292 0.708,0.156 10 false CORRECT 1.49,0.135 2.354,0.292 0.865,0.156 10 false INCORRECT 2.365,1.76 2.677,1.927 0.313,0.167 10 false SST 2.927,0.073 3.083,0.24 0.156,0.167 10 false 1 2.927,0.448 3.083,0.615 0.156,0.167 10 false 2 2.938,0.833 3.094,1 0.156,0.167 10 false 3 1.063,2.083 1.219,2.26 0.156,0.177 10 false 4 1.063,2.281 1.219,2.458 0.156,0.177 10 false 5 1.052,1.01 1.208,1.177 0.156,0.167 10 false 1 1.063,1.219 1.219,1.385 0.156,0.167 10 false 2 1.063,1.74 1.219,1.917 0.156,0.177 10 false 3 2.417,2.083 2.573,2.26 0.156,0.177 10 false 4 3.146,1.167 3.844,1.323 0.698,0.156 10 false Check Ball 3.146,1.521 4.688,1.74 1.542,0.219 10 false High Pressure Chamber 2.938,1.156 3.094,1.323 0.156,0.167 10 false 4 2.938,1.521 3.094,1.688 0.156,0.167 10 false 5 4.531,2.375 4.844,2.542 0.313,0.167 10 false SST


e.

After bleeding the air, remove SST. Then try to quickly and firmly press the plunger with your fingers.

OK:

Plunger can be pressed 3 times.


If the plunger can still be compressed after pressing it 3 times, replace the lash adjuster with a new one.


Hide 10.INSPECT INNER COMPRESSION SPRING

a.

Inspect the inner compression spring deviation.

i.
A101393E02
0.681,0.055 1.302,0.227 0.621,0.172 10 Deviation

Using a steel square, measure the deviation of the inner compression spring.

Maximum deviation:

1.5 mm (0.0591 in.)


If the deviation is more than the maximum, replace the inner compression spring.



b.

Inspect the inner compression spring free length.

i.
A101392

Using a vernier caliper, measure the free length of the inner compression spring.

Standard free length:

45.9 mm (1.81 in.)


If the free length is not as specified, replace the inner compression spring.



c.

Inspect the inner compression spring tension.

i.
EM00281

Using a spring tester, measure the tension of the inner compression spring at the specified installed length.

Installed tension:

219 to 242 N (22 to 25 kgf, 49.2 to 54.4 lbf) at 31.0 mm (1.22 in.)


If the installed tension is not as specified, replace the inner compression spring.



Hide 11.INSPECT VALVE GUIDE BUSH OIL CLEARANCE

a.
A164580

Using a caliper gauge, measure the inside diameter of the guide bush.

Standard bush inside diameter:

6.01 to 6.03 mm (0.2366 to 0.2374 in.)



b.

Subtract the valve stem diameter measurement from the guide bush inside diameter measurement.

Standard Oil Clearance:
Item Specified Condition
Intake 0.025 to 0.060 mm (0.000984 to 0.00236 in.)
Exhaust 0.035 to 0.070 mm (0.00138 to 0.00276 in.)


Maximum Oil Clearance:
Item Specified Condition
Intake 0.120 mm (0.00472 in.)
Exhaust 0.130 mm (0.00512 in.)


If the oil clearance is more than the maximum, replace the valve guide bush.


Hide 12.CLEAN VALVE

a.
EM00580

Using a gasket scraper, chip off any carbon from the valve head.

NOTICE:

Be careful not to damage the valve face.



b.

Using a wire brush, thoroughly clean the valve.


Hide 13.INSPECT VALVE

a.
A131997

Inspect the valve stem diameter.

i.

Using a micrometer, measure the diameter of the valve stem.

Standard Valve Stem Diameter:
Item Specified Condition
Intake 5.970 to 5.985 mm (0.2350 to 0.2356 in.)
Exhaust 5.960 to 5.975 mm (0.2346 to 0.2352 in.)




b.
A075611E06
2.865,1.552 3.313,1.76 0.448,0.208 10 false 45.5°

Inspect the valve face angle.

i.

Grind the valve enough to remove pits and carbon.


ii.

Check that the valve is ground to the correct valve face angle.

Standard valve face angle:

45.5°




c.
A131998E01
0.102,1.092 1.233,1.283 1.131,0.191 10 Margin Thickness

Inspect the valve head margin thickness.

i.

Using a vernier caliper, measure the valve head margin thickness.

Standard margin thickness:

1.0 mm (0.0394 in.)


Minimum margin thickness:

0.5 mm (0.0197 in.)


If the margin thickness is less than the minimum, replace the valve.



d.
A131999E01
2.236,0.951 3.156,1.121 0.920,0.169 10 Overall Length

Inspect the valve overall length.

i.

Using a vernier caliper, measure the overall length.

Standard Overall Length:
Item Specified Condition
Intake 104.4 mm (4.11 in.)
Exhaust 104.1 mm (4.10 in.)


Minimum Overall Length:
Item Specified Condition
Intake 104.1 mm (4.10 in.)
Exhaust 103.8 mm (4.09 in.)


If the overall length is less than the minimum, replace the valve.



e.
EM00255

Inspect the valve stem tip.

i.

Check the surface of the valve stem tip for wear.

NOTICE:

Do not grind the valve so it becomes shorter than the minimum overall length.


If the valve stem tip is worn, resurface the tip with a grinder or replace the valve.



Hide 14.CLEAN VALVE SEAT

a.
A164828

Using a 45° carbide cutter, resurface the valve seats.

NOTICE:

Be careful not to damage the combustion chambers and valve seats.



b.

Clean the valve seats.


Hide 15.INSPECT INTAKE VALVE SEAT

a.
A164578E03
1.406,1.833 1.896,2.177 0.49,0.344 10 true Width

Apply a light coat of Prussian blue to the valve face.


b.

Lightly press the valve face against the valve seat.

NOTICE:

Do not rotate the valve while pressing the valve.



c.

Check the valve face and valve seat.

i.

Check that the contact surfaces of the valve seat and valve face are in the middle area of their respective surfaces, with the width between 1.0 to 1.4 mm (0.0394 to 0.0551 in.).

If not, correct the valve seat.


ii.

Check that the contact surfaces of the valve seat and valve face are even around the entire valve seat.

If not, correct the valve seat.



Hide 16.INSPECT EXHAUST VALVE SEAT

a.
A164579E03
1.208,1.833 1.719,2.177 0.51,0.344 10 true Width

Apply a light coat of Prussian blue to the valve face.


b.

Lightly press the valve face against the valve seat.

NOTICE:

Do not rotate the valve while pressing the valve.



c.

Check the valve face and valve seat.

i.

Check that the contact surfaces of the valve seat and valve face are in the middle area of their respective surfaces, with the width between 1.0 to 1.4 mm (0.0394 to 0.0551 in.).

If not, correct the valve seat.


ii.

Check that the contact surfaces of the valve seat and valve face are even around the entire valve seat.

If not, correct the valve seat.



Hide 17.VISUALLY CHECK CYLINDER BLOCK

a.
A164613

Visually check the cylinder for vertical scratches.

If necessary, replace the cylinder block.


Hide 18.INSPECT CYLINDER BLOCK FOR FLATNESS

a.

Using a precision straightedge and feeler gauge, measure the warpage of the contact surface between the cylinder head and cylinder head gaskets.

A385807

Maximum warpage:

0.05 mm (0.00197 in.)


If the warpage is more than the maximum, replace the cylinder block sub-assembly.


Hide 13265 19.INSPECT CONNECTING ROD BOLT

a.
A164606E03
1.26,1.354 2.292,1.625 1.031,0.271 10 false Measuring Area

Using a vernier caliper, measure the tension portion diameter of the bolt.

Standard diameter:

8.7 to 8.8 mm (0.343 to 0.346 in.)


Minimum diameter:

8.5 mm (0.335 in.)


If the diameter is less than the minimum, replace the connecting rod bolt.


Hide 20.INSPECT CRANKSHAFT BEARING CAP BOLT

a.

Using a vernier caliper, measure the outside thread diameter of bolt A and B.

A385808E01
0.719,1.792 1.708,1.979 0.99,0.188 10 false Measuring Area 3.885,1.75 4.875,1.938 0.99,0.188 10 false Measuring Area 0.74,0.667 0.917,0.865 0.177,0.198 10 false A 3.854,0.688 4.031,0.885 0.177,0.198 10 false B

Bolt Length
Item Specified Condition
Bolt A 106 mm (4.17 in.)
Bolt B 90.5 mm (3.56 in.)

Measuring Area:
Item Specified Condition
Bolt A 73 mm (2.87 in.)
Bolt B 63 mm (2.48 in.)


Standard diameter:
for bolt A:

10.8 to 11.0 mm (0.425 to 0.433 in.)

for bolt B:

9.8 to 10.0 mm (0.386 to 0.394 in.)


Minimum diameter:
for bolt A:

10.5 mm (0.413 in.)

for bolt B:

9.5 mm (0.374 in.)


HINT:

If a visual check reveals no excessively thin areas, check the center of the bolt (see illustration) and find the area that has the lowest diameter.


If the diameter is less than the minimum, replace the crankshaft bearing cap bolt.


Hide 13101 21.INSPECT PISTON WITH PIN SUB-ASSEMBLY

a.
A164615E01
0.254,1.806 1.444,1.967 1.190,0.161 10 *: Measuring Point 0.394,1.228 0.499,1.366 0.105,0.138 10 *

Using a micrometer, measure the piston diameter at a right angle to the piston pin center line, 12 mm (0.472 in.) from the piston skirt.

Standard piston diameter:

85.932 to 85.966 mm (3.383 to 3.384 in.)


Minimum piston diameter:

85.910 mm (3.382 in.)


If the diameter is less than the minimum, replace the piston with pin sub-assembly.


Hide 22.INSPECT CYLINDER BORE

a.

Using a cylinder gauge, measure the cylinder bore diameter at positions A and B in the thrust and axial directions.

A385809E01
5.76,0.5 6.75,0.677 0.99,0.177 10 false Axial Direction 4.802,1.042 5.792,1.219 0.99,0.177 10 false Thrust Direction 4.042,0.677 4.906,0.875 0.865,0.198 10 false Engine Front 5.635,1.76 6.781,1.969 1.146,0.208 10 false 10 mm (0.394 in.) 5.552,2.094 6.063,2.281 0.51,0.188 10 false Center 4.99,1.625 5.198,1.813 0.208,0.188 10 false A 4.99,2.083 5.198,2.271 0.208,0.188 10 false B

Standard diameter:

86.000 to 86.013 mm (3.3858 to 3.3863 in.)


Maximum diameter:

86.03 mm (3.3870 in.)


If the diameter is more than the maximum, replace the cylinder block.


Hide 23.INSPECT PISTON OIL CLEARANCE

a.

Subtract the piston diameter measurement from the cylinder bore diameter measurement.

Standard oil clearance:

0.034 to 0.081 mm (0.00134 to 0.00319 in.)


Maximum oil clearance:

0.091 mm (0.00358 in.)


If the oil clearance is more than the maximum, replace all 8 pistons. If necessary, replace the cylinder block.


Hide 24.INSPECT PISTON PIN OIL CLEARANCE

a.

Check each mark on the piston, piston pin and connecting rod.

A164831E04
3.208,0.771 3.833,0.969 3.833,0.969 3.833,1.083 true 3.083,0.563 3.396,0.26 3.396,0.26 3.5,0.26 true 5.385,3.146 4.927,3.146 true 5.792,2.615 6.729,2.896 6.729,2.896 6.729,3.073 true 5.177,1.375 5,1.813 5,1.813 4.823,1.813 false 2.646,2.198 2.646,1.917 2.646,1.917 1.354,1.917 true 1.469,2.125 1.469,3.031 1.469,3.031 1.375,3.031 true 1.385,2.156 1.385,3.302 true 1.073,3.323 1.823,3.479 0.75,0.156 10 false Front Mark 0.604,1.427 0.885,1.583 0.281,0.156 10 false RH: 2.313,0.125 2.594,0.281 0.281,0.156 10 false LH: 3.521,1.104 4.271,1.26 0.75,0.156 10 false Front Mark 3.604,0.188 6.01,0.344 2.406,0.156 10 false Piston Pin Hole Inside Diameter Mark 1.969,2.208 3.365,2.552 1.396,0.344 10 false Piston Pin Hole Inside Diameter Mark 3.531,3.063 4.938,3.396 1.406,0.333 10 false Connecting Rod Bush Inside Diameter Mark 6.417,3.125 7.146,3.281 0.729,0.156 10 false Front Mark 4.104,1.729 4.813,1.906 0.708,0.177 10 false Paint Mark


b.
A164618

Using a caliper gauge, measure the inside diameter of the piston pin hole.

Standard Piston Pin Hole Inside Diameter:
Mark Specified Condition
A 29.009 to 29.013 mm (1.1421 to 1.1422 in.)
B 29.013 to 29.017 mm (1.1422 to 1.1424 in.)
C 29.017 to 29.021 mm (1.1424 to 1.1426 in.)



c.
A132060E26
0.458,2.708 1.604,2.896 1.146,0.188 10 false 5 mm (0.197 in.) 0.646,3.51 1.281,3.698 0.635,0.188 10 false 34.5 mm 0.667,3.667 1.302,3.854 0.635,0.188 10 false (1.36 in.) 1.073,4.344 2.219,4.531 1.146,0.188 10 false 5 mm (0.197 in.)

Using a micrometer, measure the piston pin diameter.

Standard Piston Pin Diameter:
Mark Paint Color Specified Condition
A White 29.000 to 29.004 mm (1.1417 to 1.1419 in.)
B Pink 29.004 to 29.008 mm (1.1419 to 1.1420 in.)
C Blue 29.008 to 29.012 mm (1.1420 to 1.1422 in.)



d.

Subtract the piston pin diameter measurement from the piston pin hole diameter measurement.

Standard oil clearance:

0.005 to 0.013 mm (0.000197 to 0.000512 in.)


Maximum oil clearance:

0.018 mm (0.000709 in.)


If the oil clearance is more than the maximum, replace the piston and piston pin as a set.


e.
A132061

Using a caliper gauge, measure the inside diameter of the connecting rod bush.

Standard Bush Inside Diameter:
Mark Specified Condition
A 29.019 to 29.023 mm (1.1425 to 1.1426 in.)
B 29.023 to 29.027 mm (1.1426 to 1.1428 in.)
C 29.027 to 29.031 mm (1.1428 to 1.1430 in.)



f.

Subtract the piston pin diameter measurement from the bush inside diameter measurement.

Standard oil clearance:

0.015 to 0.023 mm (0.000591 to 0.000906 in.)


Maximum oil clearance:

0.028 mm (0.00110 in.)


If the oil clearance is more than the maximum, replace the connecting rod and piston with pin as a set.


Hide 25.INSPECT RING GROOVE CLEARANCE

a.
A164616

Using a feeler gauge, measure the clearance between a new piston ring and the wall of the ring groove.

Standard Ring Groove Clearance:
Item Specified Condition
No. 1 compression ring 0.11 to 0.15 mm (0.00433 to 0.00591 in.)
No. 2 compression ring 0.08 to 0.12 mm (0.00315 to 0.00472 in.)
Oil ring 0.03 to 0.07 mm (0.00118 to 0.00276 in.)


If the clearance is not as specified, replace the piston.


Hide 26.INSPECT PISTON RING END GAP

a.
A164617E01
2.783,1.367 3.238,1.517 0.455,0.150 10 60 mm 0.163,1.444 0.897,1.631 0.733,0.187 10 Piston Ring 1.498,1.863 1.208,1.552 1.208,1.552 1.082,1.552 false

Insert the piston ring into the cylinder bore.


b.

Using a piston, push the piston ring a little beyond the bottom of the ring travel, 60 mm (2.36 in.) from the top of the cylinder block.


c.
A101491

Using a feeler gauge, measure the end gap.

Standard End Gap:
Item Specified Condition
No. 1 compression ring 0.20 to 0.30 mm (0.00787 to 0.0118 in.)
No. 2 compression ring 0.47 to 0.62 mm (0.0185 to 0.0244 in.)
Oil ring 0.10 to 0.40 mm (0.00394 to 0.0157 in.)


Maximum End Gap:
Item Specified Condition
No. 1 compression ring 0.40 mm (0.0157 in.)
No. 2 compression ring 0.75 mm (0.0295 in.)
Oil ring 0.50 mm (0.0197 in.)


If the end gap is more than the maximum, replace the piston ring. If the end gap is more than the maximum even with a new piston ring, replace the cylinder block.


Hide 27.INSPECT CONNECTING ROD SUB-ASSEMBLY

a.
A132171

Using a rod aligner and feeler gauge, check the connecting rod alignment.

i.

Check for bend.

Maximum bend:

0.07 mm (0.00276 in.) per 100 mm (3.94 in.)


If the bend is more than the maximum, replace the connecting rod sub-assembly.


ii.
A132172

Check for twist.

Maximum twist:

0.15 mm (0.00591 in.) per 100 mm (3.94 in.)


If the twist is more than the maximum, replace the connecting rod sub-assembly.



Hide 13411 28.INSPECT CRANKSHAFT

a.
A164607

Using a dial indicator and V-blocks, measure the runout as shown in the illustration.

Maximum circle runout:

0.04 mm (0.00157 in.)


If the circle runout is more than the maximum, replace the crankshaft.


b.
A142818

Using a micrometer, measure the diameter of each main journal.

Standard diameter:

74.982 to 75.000 mm (2.9520 to 2.9527 in.)


If the diameter is not as specified, check the oil clearance. If necessary, replace the crankshaft.


c.

Check each main journal for taper and out-of-round as shown in the illustration.

Maximum taper and out-of-round:

0.01 mm (0.000394 in.)


If the taper and out-of-round is more than the maximum, replace the crankshaft.


d.
A142817

Using a micrometer, measure the diameter of each crank pin.

Standard diameter:

54.982 to 55.000 mm (2.1646 to 2.1653 in.)


If the diameter is not as specified, check the oil clearance. If necessary, replace the crankshaft.


e.

Check each crank pin for taper and out-of-round as shown in the illustration.

Maximum taper and out-of-round:

0.01 mm (0.000394 in.)


If the taper and out-of-round is more than the maximum, replace the crankshaft.


Hide 30.INSPECT CRANKSHAFT OIL CLEARANCE

HINT:
A164803E01
0.133,0.046 1.260,0.385 1.127,0.339 10 No. 1 and 5 Journal Bearings: 1.965,0.046 3.112,0.367 1.146,0.321 10 No. 2, 3 and 5 Journal Bearings: 0.074,1.794 0.674,1.949 0.599,0.155 10 22.5 mm 1.804,1.794 2.384,1.949 0.580,0.155 10 20.5 mm

Main bearings come in widths of 20.5 mm (0.807 in.) and 22.5 mm (0.886 in.).

Standard Bearing Width
Item Specified Condition
No. 1 and 5 journal bearings 22.5 mm (0.886 in.)
No. 2, 3 and 4 journal bearings 20.5 mm (0.807 in.)


a.

Clean each main journal and bearing.


b.
A164628

Align the bearing claw with the claw groove of the cylinder block, and push in the 5 upper bearings.

NOTICE:
·

Do not apply engine oil to the bearings and the contact surfaces.

·

Do not allow coolant to come into contact with the bearing inner surface. If any coolant comes into contact with the bearing inner surface, replace the bearing with a new one.

·

Both sides of the oil groove in the cylinder block should be visible through the oil feed holes in the bearing. The amount visible on each side of the holes should be equal.




c.
A164629

Align the bearing claw with the claw groove of the main bearing cap, and push in the 5 lower bearings.

NOTICE:
·

Do not apply engine oil to the bearings and the contact surfaces.

·

Do not allow coolant to come into contact with the bearing inner surface.

If any coolant comes into contact with the bearing inner surface, replace the bearing with a new one.



HINT:

A number marked on each main bearing cap indicates the installation position.



d.
A164570

Place the crankshaft on the cylinder block.


e.
A164567E03
1.698,0.969 1.146,0.156 1.146,0.156 0.99,0.156 true 0.281,0.063 0.958,0.26 0.677,0.198 10 false Plastigage

Lay a strip of Plastigage across each journal.


f.
A164632E01
0.108,1.082 0.477,1.240 0.368,0.158 10 Front

Examine the front marks and numbers and install the crankshaft bearing caps to the cylinder block.

NOTICE:

Do not turn the crankshaft.



g.

Apply a light coat of engine oil to the threads of the crankshaft bearing cap bolts.


h.

Temporarily install the crankshaft bearing cap bolts labeled A or the bolts labeled B.

A385765E01
1.74,0.729 1.563,0.729 1.563,0.729 1.156,0.583 true 1.813,0.646 2.313,0.813 0.5,0.167 10 false Spacer 0.948,0.854 1.406,1.031 0.458,0.177 10 false 8 mm 4.76,0.906 5.906,1.083 1.146,0.177 10 false 106 mm (4.17 in.) 4.667,2.167 5.875,2.344 1.208,0.177 10 false 90.5 mm (3.56 in.) 6.135,0.427 6.635,0.604 0.5,0.177 10 false 11 mm 6.104,0.604 6.74,0.792 0.635,0.188 10 false (0.433 in.) 6.052,1.667 6.531,1.854 0.479,0.188 10 false 10 mm 6.031,1.844 6.708,2.063 0.677,0.219 10 false (0.394 in.) 4.031,0.5 4.219,0.677 0.188,0.177 10 false A 4.042,1.75 4.229,1.927 0.188,0.177 10 false B

HINT:

In place of cylinder block stiffening plates, install 8 mm (0.315 in.) thick spacers to the crankshaft bearing cap bolts.



i.

Uniformly tighten the 2 crankshaft bearing cap bolts for each bearing cap in several passes to ensure a proper fit.

NOTICE:

Do not tap the bearing cap with a plastic-faced hammer.



j.

Remove the crankshaft bearing cap bolts and spacers.


k.
U162923E02
2.594,0.531 1.75,0.115 1.75,0.115 2.646,1.521 true 1.5,0.115 1.74,0.115 false 0.781,0.031 1.906,0.281 1.125,0.25 10 true Front Mark

Set the 2 cylinder block stiffening plates on the cylinder block.

HINT:

Make sure the arrows on the stiffening plates face the engine front.



l.
U163108E02
1.365,2.646 1.521,2.813 0.156,0.167 10 false A 1.375,3 1.531,3.167 0.156,0.167 10 false B 2.135,1.625 2.292,1.792 0.156,0.167 10 false 1 0.802,0.969 0.979,1.135 0.177,0.167 10 false 10 2.135,0.969 2.292,1.135 0.156,0.167 10 false 2 1.656,2.219 1.833,2.385 0.177,0.167 10 false 11 2.76,0.979 2.917,1.146 0.156,0.167 10 false 3 1.667,0.344 1.844,0.51 0.177,0.167 10 false 12 2.771,1.625 2.927,1.792 0.156,0.167 10 false 4 2.281,0.344 2.458,0.51 0.177,0.167 10 false 13 1.521,1.625 1.677,1.792 0.156,0.167 10 false 5 2.281,2.229 2.458,2.396 0.177,0.167 10 false 14 1.51,0.969 1.667,1.135 0.156,0.167 10 false 6 1.031,2.219 1.208,2.385 0.177,0.167 10 false 15 3.26,1.083 3.417,1.25 0.156,0.167 10 false 7 1.042,0.333 1.219,0.5 0.177,0.167 10 false 16 3.25,1.875 3.406,2.042 0.156,0.167 10 false 8 3,0.344 3.177,0.51 0.177,0.167 10 false 17 0.833,1.615 0.99,1.781 0.156,0.167 10 false 9 3,2.219 3.177,2.385 0.177,0.167 10 false 18 0.323,2.229 0.5,2.396 0.177,0.167 10 false 19 0.344,0.344 0.521,0.51 0.177,0.167 10 false 20

Step 1:

HINT:
·

The crankshaft bearing cap bolts are tightened in 3 progressive steps.

·

If any crankshaft bearing cap bolt is broken or deformed, replace it.



i.

Apply a light coat of engine oil to the threads and under the heads of the 20 crankshaft bearing cap bolts.


ii.

Install the 20 crankshaft bearing cap bolts. Using several steps, tighten the bolts uniformly in the sequence shown in the illustration.

Torque:
for bolt A : 35 N*m (357 kgf*cm, 26 ft.*lbf)
for bolt B : 60 N*m (612 kgf*cm, 44 ft.*lbf)



m.
U162928E02
1.188,3.458 2.115,3.99 2.115,3.99 2.354,3.99 true 2.125,1.344 2.281,1.51 0.156,0.167 10 false 1 0.802,0.698 0.979,0.865 0.177,0.167 10 false 10 2.135,0.698 2.292,0.865 0.156,0.167 10 false 2 1.667,1.938 1.844,2.104 0.177,0.167 10 false 11 2.771,0.708 2.927,0.875 0.156,0.167 10 false 3 1.677,0.083 1.854,0.25 0.177,0.167 10 false 12 2.76,1.344 2.917,1.51 0.156,0.167 10 false 4 2.292,0.083 2.469,0.25 0.177,0.167 10 false 13 1.521,1.344 1.677,1.51 0.156,0.167 10 false 5 2.281,1.938 2.458,2.104 0.177,0.167 10 false 14 1.521,0.698 1.677,0.865 0.156,0.167 10 false 6 1.042,1.927 1.219,2.094 0.177,0.167 10 false 15 3.271,0.792 3.427,0.958 0.156,0.167 10 false 7 1.042,0.083 1.219,0.25 0.177,0.167 10 false 16 3.26,1.583 3.417,1.75 0.156,0.167 10 false 8 3.01,0.094 3.188,0.26 0.177,0.167 10 false 17 0.823,1.344 0.979,1.51 0.156,0.167 10 false 9 3,1.927 3.177,2.094 0.177,0.167 10 false 18 0.323,1.938 0.5,2.104 0.177,0.167 10 false 19 0.354,0.094 0.531,0.26 0.177,0.167 10 false 20 0.104,3.688 0.469,3.833 0.365,0.146 10 false Front 0.646,4.115 0.802,4.281 0.156,0.167 10 false A 0.646,4.427 0.802,4.594 0.156,0.167 10 false B 0.719,2.677 0.979,2.844 0.26,0.167 10 false 90° 2.417,3.906 3.271,4.052 0.854,0.146 10 false Painted Mark

Step 2:

i.

Mark the front side of the crankshaft bearing cap bolts A and B with paint.


ii.

Tighten the crankshaft bearing cap bolts A and B 90° in the sequence shown in the illustration.



n.
U162929E02
1.594,2.938 2.104,3.979 2.104,3.979 2.26,3.979 true 2.135,1.344 2.292,1.51 0.156,0.167 10 false 1 0.802,0.698 0.979,0.865 0.177,0.167 10 false 10 2.135,0.688 2.292,0.854 0.156,0.167 10 false 2 2.771,0.698 2.927,0.865 0.156,0.167 10 false 3 2.771,1.344 2.927,1.51 0.156,0.167 10 false 4 1.521,1.344 1.677,1.51 0.156,0.167 10 false 5 1.521,0.688 1.677,0.854 0.156,0.167 10 false 6 3.26,0.792 3.417,0.958 0.156,0.167 10 false 7 3.26,1.583 3.417,1.75 0.156,0.167 10 false 8 0.833,1.333 0.99,1.5 0.156,0.167 10 false 9 0.083,3.625 0.448,3.792 0.365,0.167 10 false Front 0.646,4.344 0.802,4.51 0.156,0.167 10 false A 2.26,2.521 2.51,2.688 0.25,0.167 10 false 90° 2.323,3.896 3.167,4.063 0.844,0.167 10 false Painted Mark

Step 3:

i.

Tighten the crankshaft bearing cap bolts A another 90° in the sequence shown in the illustration.


ii.
A170349E05
2.365,1.167 2.771,1.406 2.771,1.406 2.771,1.542 true 0.354,1.438 0.771,1.635 0.417,0.198 10 false Front 2.323,1.583 3.167,1.74 0.844,0.156 10 false Painted Mark

Check that the painted marks of bolts A are now at a 180° angle to the front.


iii.
A170350E06
1.802,0.573 2.063,0.25 2.063,0.25 2.177,0.25 true 2.229,0.177 3.094,0.448 0.865,0.271 10 false Painted Mark 0.354,1.427 0.75,1.667 0.396,0.24 10 false Front

Check that the painted marks of bolts B are now at a 90° angle to the front.

NOTICE:

Do not turn the crankshaft.




o.
U162921E02
1.708,1.927 1.865,2.094 0.156,0.167 10 false 1 0.344,0.104 0.521,0.271 0.177,0.167 10 false 10 1.719,0.094 1.875,0.26 0.156,0.167 10 false 2 2.333,0.094 2.49,0.26 0.156,0.167 10 false 3 2.333,1.927 2.49,2.094 0.156,0.167 10 false 4 1.094,1.927 1.25,2.094 0.156,0.167 10 false 5 1.083,0.094 1.24,0.26 0.156,0.167 10 false 6 3.052,0.104 3.208,0.271 0.156,0.167 10 false 7 2.938,1.802 3.094,1.969 0.156,0.167 10 false 8 0.385,1.927 0.542,2.094 0.156,0.167 10 false 9

Step 4:

i.

Using several steps, install the 10 crankshaft bearing cap bolts uniformly in the sequence shown in the illustration.

Torque:
56 N*m (571 kgf*cm, 41 ft.*lbf)



p.

Remove the crankshaft bearing caps.

i.
U162920E02
0.385,0.073 0.542,0.24 0.156,0.167 10 false 1 1.667,1.896 1.844,2.063 0.177,0.167 10 false 10 0.385,1.906 0.542,2.073 0.156,0.167 10 false 2 2.938,1.781 3.094,1.948 0.156,0.167 10 false 3 3.042,0.073 3.198,0.24 0.156,0.167 10 false 4 1.083,0.073 1.24,0.24 0.156,0.167 10 false 5 1.083,1.906 1.24,2.073 0.156,0.167 10 false 6 2.344,1.917 2.5,2.083 0.156,0.167 10 false 7 2.333,0.073 2.49,0.24 0.156,0.167 10 false 8 1.719,0.073 1.875,0.24 0.156,0.167 10 false 9

Step 1:

Using several steps, loosen and remove the 10 crankshaft bearing cap set bolts uniformly in the sequence shown in the illustration.


ii.
U162922E02
0.385,0.094 0.542,0.26 0.156,0.167 10 false 1 1.667,1.896 1.844,2.063 0.177,0.167 10 false 10 0.375,1.917 0.531,2.083 0.156,0.167 10 false 2 0.781,0.688 0.958,0.854 0.177,0.167 10 false 11 2.896,1.781 3.052,1.948 0.156,0.167 10 false 3 0.781,1.333 0.958,1.5 0.177,0.167 10 false 12 3.042,0.094 3.198,0.26 0.156,0.167 10 false 4 3.208,1.188 3.385,1.354 0.177,0.167 10 false 13 1.094,0.094 1.25,0.26 0.156,0.167 10 false 5 3.208,0.792 3.385,0.958 0.177,0.167 10 false 14 1.083,1.917 1.24,2.083 0.156,0.167 10 false 6 1.458,0.677 1.635,0.844 0.177,0.167 10 false 15 2.323,1.917 2.479,2.083 0.156,0.167 10 false 7 1.458,1.323 1.635,1.49 0.177,0.167 10 false 16 2.333,0.094 2.49,0.26 0.156,0.167 10 false 8 2.729,1.323 2.906,1.49 0.177,0.167 10 false 17 1.719,0.094 1.875,0.26 0.156,0.167 10 false 9 2.74,0.688 2.917,0.854 0.177,0.167 10 false 18 2.083,0.688 2.26,0.854 0.177,0.167 10 false 19 2.083,1.323 2.26,1.49 0.177,0.167 10 false 20

Step 2:

Using several steps, loosen and remove the 20 crankshaft bearing cap set bolts uniformly in the sequence shown in the illustration.



q.
A164799

Remove the 2 cylinder block stiffening plates.


r.
A164847

Using 2 crankshaft bearing cap set bolts, pull out the 5 bearing caps.

NOTICE:

Take care not to damage the contact surface of the crankshaft bearing cap and cylinder block.



s.
A164568

Measure the Plastigage at its widest point.

Standard Oil Clearance:
Item Specified Condition
No. 1 and 3 journals 0.020 to 0.038 mm (0.000787 to 0.00150 in.)
No. 2, 4 and 5 journals 0.032 to 0.050 mm (0.00126 to 0.00197 in.)


Maximum Clearance:
Item Specified Condition
No. 1 and 3 journals 0.048 mm (0.00189 in.)
No. 2, 4 and 5 journals 0.060 mm (0.00236 in.)


If the oil clearance is more than the maximum, use an over size bearing and correct or regrind the crankshaft so that the oil clearance is as shown in the table below.

Oil Clearance (Use for Over Size Bearing):
Item Specified Condition
No. 1 and 3 journals 0.021 to 0.061 mm (0.000827 to 0.00240 in.)
No. 2, 4 and 5 journals 0.033 to 0.073 mm (0.00130 to 0.00287 in.)


HINT:

Make sure to replace the upper and lower main bearings as one set.



t.

Completely remove the Plastigage.


u.

If replacing a bearing, replace it with one that has the same number. If the number of the bearing cannot be determined, select the correct bearing by adding together the numbers imprinted on the cylinder block and crankshaft, then refer to the appropriate bearing number. There are 7 sizes of standard bearings, marked "1", "2", "3", "4", "5", "6" and "7" accordingly.

A385814E01
0.917,2.292 0.917,2.125 0.917,2.125 1.781,1.583 true 1.375,2.292 1.375,2.125 1.375,2.125 1.875,1.594 true 2.302,2.302 2.302,2.135 2.302,2.135 2.031,1.583 true 2.708,2.292 2.708,2.125 2.708,2.125 2.125,1.594 true 1.927,2.271 1.948,1.594 true 5.094,2.01 5.229,2.01 5.229,2.01 5.458,2.323 true 5.115,2.542 5.25,2.542 5.25,2.542 5.469,2.417 true 5.583,2.406 5.958,2.552 5.958,2.552 6.094,2.552 true 5.656,2.323 5.958,2.01 5.958,2.01 6.094,2.01 true 5.552,2 5.948,1.677 5.948,1.677 6.083,1.677 true 5.552,2.302 5.552,2.01 true 1.813,3.479 2.083,3.375 false 5.427,3.469 5.698,3.365 false 5.417,3.833 5.729,3.823 false 1.813,3.844 2.125,3.833 false 0.167,0.135 1.396,0.417 1.229,0.281 12 false Cylinder Block: 3.635,0.125 4.865,0.406 1.229,0.281 12 false Crankshaft: 0.146,2.885 2.469,3.125 2.323,0.24 12 false No. 1 and 5 Journal Bearings: 3.49,2.844 5.813,3.083 2.323,0.24 12 false No. 2, 3 and 4 Journal Bearings: 0.51,4.354 1.375,4.594 0.865,0.24 10 false Number Mark 0.552,1.969 1.417,2.208 0.865,0.24 10 false Front 0.719,2.323 1.125,2.531 0.406,0.208 10 false No. 1 1.198,2.333 1.563,2.51 0.365,0.177 10 false No. 2 1.688,2.333 2.052,2.51 0.365,0.177 10 false No. 3 2.146,2.344 2.51,2.521 0.365,0.177 10 false No. 4 2.594,2.344 2.958,2.521 0.365,0.177 10 false No. 5 6.167,2.458 6.531,2.635 0.365,0.177 10 false No. 5 4.729,2.458 5.094,2.635 0.365,0.177 10 false No. 4 6.156,1.604 6.521,1.781 0.365,0.177 10 false No. 2 4.708,1.938 5.115,2.146 0.406,0.208 10 false No. 1 6.146,1.927 6.51,2.104 0.365,0.177 10 false No. 3 1.552,4.24 2.854,4.427 1.302,0.188 10 false 22.5 mm (0.886 in.) 5.188,4.26 6.49,4.448 1.302,0.188 10 false 20.5 mm (0.807 in.) 2.177,3.292 2.594,3.479 0.417,0.188 10 false Upper 5.771,3.281 6.188,3.469 0.417,0.188 10 false Upper 5.802,3.729 6.219,3.917 0.417,0.188 10 false Lower 2.188,3.75 2.604,3.938 0.417,0.188 10 false Lower

EXAMPLE

Cylinder block main journal bore diameter "1" (A) + Crankshaft main journal diameter "2" (B) = Total number 3 (use bearing "3" (C))

No. 1 to No. 5 on Cylinder Block:
Cylinder Block (A) Crankshaft (B) Use Bearing (C)
"1" "0" "1"
"1" "2"
"2" "3"
"3" "4"
"4" "5"
"2" "0" "2"
"1" "3"
"2" "4"
"3" "5"
"4" "6"
"3" "0" "3"
"1" "4"
"2" "5"
"3" "6"
"4" "7"


Standard Cylinder Block Main Journal Bore Diameter (A):
Item Mark Specified Condition
No. 1 and 3 journals "1" 79.000 to 79.006 mm (3.11023 to 3.11047 in.)
"2" More than 79.006 to 79.012 mm (more than 3.11047 to 3.11070 in.)
"3" More than 79.012 to 79.018 mm (more than 3.11070 to 3.11094 in.)
No. 2, 4 and 5 journals "1" 79.000 to 79.006 mm (3.11023 to 3.11047 in.)
"2" More than 79.006 to 79.012 mm (more than 3.11047 to 3.11070 in.)
"3" More than 79.012 to 79.018 mm (more than 3.11070 to 3.11094 in.)


Standard Crankshaft Main Journal Diameter (B):
Item Mark Specified Condition
No. 1 and 3 journals "2" More than 74.994 to 75.000 mm (more than 2.95251 to 2.95275 in.)
"3" More than 74.988 to 74.994 mm (more than 2.95228 to 2.95251 in.)
"4" 74.982 to 74.988 mm (2.95204 to 2.95228 in.)
No. 2, 4 and 5 journals "0" More than 74.994 to 75.000 mm (more than 2.95251 to 2.95275 in.)
"1" More than 74.988 to 74.994 mm (more than 2.95288 to 2.95251 in.)
"2" 74.982 to 74.988 mm (2.95204 to 2.95228 in.)


Standard Crankshaft Bearing Center Wall Thickness (C):
Item Mark Specified Condition
(for Upper Bearing)
Specified Condition
(for Lower Bearing)
No. 1 and 5 journal bearings "1" More than 1.987 to 1.990 mm (more than 0.07823 to 0.07835 in.) More than 1.975 to 1.978 mm (more than 0.07776 to 0.07787 in.)
"2" More than 1.990 to 1.993 mm (more than 0.07835 to 0.07846 in.) More than 1.978 to 1.981 mm (more than 0.07787 to 0.07799 in.)
"3" More than 1.993 to 1.996 mm (more than 0.07846 to 0.07858 in.) More than 1.981 to 1.984 mm (more than 0.07799 to 0.07811 in.)
"4" More than 1.996 to 1.999 mm (more than 0.07858 to 0.07870 in.) More than 1.984 to 1.987 mm (more than 0.07811 to 0.07823 in.)
"5" More than 1.999 to 2.002 mm (more than 0.07870 to 0.07882 in.) More than 1.987 to 1.990 mm (more than 0.07823 to 0.07835 in.)
"6" More than 2.002 to 2.005 mm (more than 0.07882 to 0.07894 in.) More than 1.990 to 1.993 mm (more than 0.07835 to 0.07846 in.)
"7" More than 2.005 to 2.008 mm (more than 0.07894 to 0.07905 in.) More than 1.993 to 1.996 mm (more than 0.07846 to 0.07858 in.)
No. 2, 3 and 4 journal bearings "1" More than 1.975 to 1.978 mm (more than 0.07776 to 0.07787 in.) More than 1.987 to 1.990 mm (more than 0.07823 to 0.07835 in.)
"2" More than 1.978 to 1.981 mm (more than 0.07787 to 0.07799 in.) More than 1.990 to 1.993 mm (more than 0.07835 to 0.07846 in.)
"3" More than 1.981 to 1.984 mm (more than 0.07799 to 0.07811 in.) More than 1.993 to 1.996 mm (more than 0.07846 to 0.07858 in.)
"4" More than 1.984 to 1.987 mm (more than 0.07811 to 0.07823 in.) More than 1.996 to 1.999 mm (more than 0.07858 to 0.07870 in.)
"5" More than 1.987 to 1.990 mm (more than 0.07823 to 0.07835 in.) More than 1.999 to 2.002 mm (more than 0.07870 to 0.07882 in.)
"6" More than 1.990 to 1.993 mm (more than 0.07835 to 0.07846 in.) More than 2.002 to 2.005 mm (more than 0.07882 to 0.07894 in.)
"7" More than 1.993 to 1.996 mm (more than 0.07846 to 0.07858 in.) More than 2.005 to 2.008 mm (more than 0.07894 to 0.07905 in.)



Hide 32.INSPECT CONNECTING ROD OIL CLEARANCE



c.
A164563E03
1.646,0.844 0.635,1.719 0.635,1.719 0.635,1.833 true 0.208,1.813 1,2.167 0.792,0.354 10 true Plastigage

Lay a strip of Plastigage across the crank pin.


d.
A164564E04
1.802,0.979 2.333,1.219 2.333,1.219 2.333,1.49 true 2.094,1.5 3.302,2.104 1.208,0.604 10 true Protrusion 2.927,0.417 3.292,0.563 0.365,0.146 10 false Front

Install the connecting rod cap so that its protrusion is facing the correct direction.

NOTICE:

Match the numbered connecting rod cap with the connecting rod.



e.

Apply a light coat of engine oil to the threads of the connecting rod cap bolts.


f.
A164565

Step 1:

HINT:
·

The connecting rod bearing cap bolts are tightened in 2 progressive steps.

·

If any connecting rod bearing cap bolt is broken or deformed, replace it.



i.

Install and alternately tighten the bolts of the connecting rod cap in several steps.

Torque:
35 N*m (357 kgf*cm, 26 ft.*lbf)



g.
A158686E09
1.49,1.156 1.208,1.656 1.208,1.656 1.208,1.802 true 0.135,1.354 0.49,1.51 0.354,0.156 10 false Front 0.76,1.844 1.615,2 0.854,0.156 10 false Painted Mark 1.042,0.365 1.281,0.531 0.24,0.167 10 false 90°

Step 2:

i.

Mark the front side of each connecting rod cap bolt with paint.


ii.

Tighten the bearing cap bolts in step 1 90°.



h.

Remove the 2 bolts, connecting rod cap and lower bearing.


i.
A164566

Measure the Plastigage at its widest point.

Standard oil clearance:

0.024 to 0.042 mm (0.000945 to 0.00165 in.)


Maximum oil clearance:

0.052 mm (0.00205 in.)


If the oil clearance is more than the maximum, replace the bearings. If necessary, replace the crankshaft.


j.

Completely remove the Plastigage.


k.

If replacing a bearing, replace it with one that has the same number marked on the connecting rod. There are 5 sizes of standard bearings, marked "1 ", "2", "3", "4" and "5" accordingly.

Select the correct bearing by adding together the number marks imprinted on the connecting rod and crankshaft.

EXAMPLE

Connecting rod "1" (A) + Crank pin "2" (B) = Total number 3 (use bearing "3" (C))

A385820E01
2.083,3.115 2.344,3.115 2.344,3.115 2.344,2.354 true 2.594,3.115 2.406,3.115 2.406,3.115 2.406,2.354 true 2.083,1.927 2.344,1.927 2.344,1.927 2.344,2.219 true 2.542,1.927 2.406,1.927 2.406,1.927 2.406,2.219 true 0.125,0.104 1.167,0.354 1.042,0.25 12 false Crankshaft: 3.781,0.823 5.198,1.063 1.417,0.24 12 false Connecting Rod: 5.635,0.823 6.875,1.271 1.24,0.448 12 false Connecting Rod Bearing: 0.365,3.375 1.292,3.583 0.927,0.208 10 false Number Mark 1.313,1.844 2.135,2.031 0.823,0.188 10 false No. 1 and 2 2.615,1.844 3.438,2.031 0.823,0.188 10 false No. 3 and 4 1.302,3.021 2.125,3.208 0.823,0.188 10 false No. 5 and 6 2.656,3.021 3.479,3.208 0.823,0.188 10 false No. 7 and 8

Standard Connecting Rod Big End Inside Diameter (A):
Mark Specified Condition
"1" 58.000 to 58.006 mm (2.28346 to 2.28370 in.)
"2" More than 58.006 to 58.012 mm (more than 2.28370 to 2.28393 in.)
"3" More than 58.012 to 58.018 mm (more than 2.28393 to 2.28417 in.)


Standard Crankshaft Pin Diameter (B):
Mark Specified Condition
"0" More than 54.994 to 55.000 mm (more than 2.16511 to 2.16535 in.)
"1" More than 54.988 to 54.994 mm (more than 2.16488 to 2.16511 in.)
"2" 54.982 to 54.988 mm (2.16464 to 2.16488 in.)


Standard Bearing Center Wall Thickness (C):
Mark Specified Condition
"1" More than 1.485 to 1.488 mm (more than 0.05846 to 0.05858 in.)
"2" More than 1.488 to 1.491 mm (more than 0.05858 to 0.05870 in.)
"3" More than 1.491 to 1.494 mm (more than 0.05870 to 0.05882 in.)
"4" More than 1.494 to 1.497 mm (more than 0.05882 to 0.05894 in.)
"5" More than 1.497 to 1.500 mm (more than 0.05894 to 0.05910 in.)




m.

Remove the crankshaft bearing.


Hide 13506 33.INSPECT NO. 1 CHAIN

a.
A139523E03
2.596,0.005 3.011,0.147 0.415,0.142 10 147 N 2.873,1.764 3.094,1.920 0.221,0.156 10 16 0.692,1.764 0.834,1.930 0.142,0.165 10 1 0.839,1.764 0.976,1.906 0.137,0.142 10 2 1.01,1.764 1.147,1.906 0.137,0.142 10 3 1.18,1.764 1.318,1.906 0.137,0.142 10 4 1.366,1.764 1.503,1.906 0.137,0.142 10 5 1.543,1.764 1.680,1.906 0.137,0.142 10 6 1.287,0.993 2.332,1.149 1.045,0.156 10 Measuring Area

Using a spring scale, pull the No. 1 chain with a force of 147 N (15 kgf, 33.1 lbf) and measure the length of the No. 1 chain using a vernier caliper.

Maximum chain elongation:

143.95 mm (5.67 in.)


NOTICE:

Perform the measurement at 3 random places.


If the elongation is more than the maximum, replace the No. 1 chain.


Hide 34.INSPECT NO. 2 CHAIN

a.
A139523E03
2.596,0.005 3.011,0.147 0.415,0.142 10 147 N 2.873,1.764 3.094,1.920 0.221,0.156 10 16 0.692,1.764 0.834,1.930 0.142,0.165 10 1 0.839,1.764 0.976,1.906 0.137,0.142 10 2 1.01,1.764 1.147,1.906 0.137,0.142 10 3 1.18,1.764 1.318,1.906 0.137,0.142 10 4 1.366,1.764 1.503,1.906 0.137,0.142 10 5 1.543,1.764 1.680,1.906 0.137,0.142 10 6 1.287,0.993 2.332,1.149 1.045,0.156 10 Measuring Area

Using a spring scale, pull the No. 2 chain with a force of 147 N (15 kgf, 33.1 lbf) and measure the length of the No. 2 chain using a vernier caliper.

Maximum chain elongation:

143.95 mm (5.67 in.)


NOTICE:

Perform the measurement at 3 random places.


If the elongation is more than the maximum, replace the No. 2 chain.


Hide 13616 35.INSPECT FUEL SUPPLY PUMP SHAFT SPROCKET

a.
A164844

Wrap the No. 1 chain around the sprocket place for the No. 1 chain.


b.

Using a vernier caliper, measure the sprocket with the chain.

Minimum gear diameter (with chain):

101.55 mm (4.00 in.)


HINT:

The vernier caliper must contact the chain rollers for the measurement.


If the diameter is less than the minimum, replace the No. 1 chain sub-assembly and fuel supply pump shaft sprocket.


c.
A164843

Wrap the No. 2 chain around the sprocket place for the No. 2 chain.


d.

Using a vernier caliper, measure the sprocket with the No. 2 chain.

Minimum gear diameter (with chain):

101.55 mm (4.00 in.)


HINT:

The vernier caliper must contact the chain rollers for the measurement.


If the diameter is less than the minimum, replace the No. 2 chain sub-assembly and fuel supply pump shaft sprocket.


Hide 13523 36.INSPECT NO. 1 CAMSHAFT TIMING SPROCKET

a.
A164585

Wrap the No. 1 chain around the sprocket.


b.

Using a vernier caliper, measure the No. 1 camshaft timing sprocket diameter with the No. 1 chain.

Minimum gear diameter (with chain):

134.90 mm (5.31 in.)


HINT:

The vernier caliper must contact the chain rollers for the measurement.


If the diameter is less than the minimum, replace the No. 1 chain sub-assembly and No. 1 camshaft timing sprocket.


Hide 13529G 37.INSPECT NO. 2 CAMSHAFT TIMING SPROCKET

a.
A164584

Wrap the No. 2 chain around the sprocket.


b.

Using a vernier caliper, measure the No. 2 camshaft timing sprocket diameter with the No. 2 chain.

Minimum gear diameter (with chain):

134.90 mm (5.31 in.)


HINT:

The vernier caliper must contact the chain rollers for the measurement.


If the diameter is less than the minimum, replace the No. 2 chain sub-assembly and No. 2 camshaft timing sprocket.


Hide 13581 38.INSPECT NO. 1 IDLE GEAR SHAFT OIL CLEARANCE

a.
A385822

Using a micrometer, measure the No. 1 idle gear shaft diameter.

Standard idle gear shaft diameter:

44.947 to 44.975 mm (1.770 to 1.771 in.)



b.
A164595

Using a caliper gauge, measure the inside diameter of the idle gear.

Standard idle gear inside diameter:

45.000 to 45.025 mm (1.772 to 1.773 in.)



c.

Subtract the No. 1 idle gear shaft diameter measurement from the idle gear inside diameter measurement.

Standard oil clearance:

0.025 to 0.078 mm (0.000984 to 0.00307 in.)


Maximum oil clearance:

0.078 mm (0.00307 in.)


If the thrust oil clearance is more than the maximum, replace the No. 1 idle gear shaft and idle gear as a set.


Hide 13540 39.INSPECT NO. 1 CHAIN TENSIONER ASSEMBLY

a.
A164586E03
1.292,1.198 0.844,1.646 0.844,1.646 0.844,1.781 true 2.208,1.24 1.885,0.26 1.885,0.26 1.74,0.26 true 1.229,0.177 1.76,0.396 0.531,0.219 10 false Plunger 0.365,1.813 1.25,2.083 0.885,0.271 10 false Stopper Plate

Move the stopper plate clockwise to release the lock. Push the plunger and check that it moves smoothly.

If necessary, replace the No. 1 chain tensioner assembly.


Hide 40.INSPECT NO. 2 CHAIN TENSIONER ASSEMBLY

a.
A164586E03
1.292,1.198 0.844,1.646 0.844,1.646 0.844,1.781 true 2.208,1.24 1.885,0.26 1.885,0.26 1.74,0.26 true 1.229,0.177 1.76,0.396 0.531,0.219 10 false Plunger 0.365,1.813 1.25,2.083 0.885,0.271 10 false Stopper Plate

Move the stopper plate clockwise to release the lock. Push the plunger and check that it moves smoothly.

If necessary, replace the No. 2 chain tensioner assembly.


Hide 13559 41.INSPECT NO. 1 CHAIN TENSIONER SLIPPER

a.
A164588E01
2.659,1.174 3.069,1.337 0.410,0.163 10 Depth 0.336,0.365 0.465,0.529 0.129,0.164 10 A 1.454,0.898 1.606,1.062 0.152,0.164 10 A 1.864,1.899 2.182,2.063 0.318,0.164 10 A-A

Measure the worn depth of the No. 1 chain tensioner slipper.

Maximum depth:

1.0 mm (0.0394 in.)


If the depth is more than the maximum, replace the No. 1 chain tensioner slipper.


Hide 13559 42.INSPECT NO. 2 CHAIN TENSIONER SLIPPER

a.
A164588E01
2.659,1.174 3.069,1.337 0.410,0.163 10 Depth 0.336,0.365 0.465,0.529 0.129,0.164 10 A 1.454,0.898 1.606,1.062 0.152,0.164 10 A 1.864,1.899 2.182,2.063 0.318,0.164 10 A-A

Measure the worn depth of the No. 2 chain tensioner slipper.

Maximum depth:

1.0 mm (0.0394 in.)


If the depth is more than the maximum, replace the No. 2 chain tensioner slipper.


Hide 13561 43.INSPECT NO. 1 CHAIN VIBRATION DAMPER

a.
A164587E01
2.643,1.196 3.051,1.368 0.408,0.172 10 Depth 0.456,0.46 0.579,0.612 0.123,0.151 10 A 1.867,1.93 2.122,2.081 0.254,0.151 10 A-A 1.563,1 1.686,1.151 0.123,0.151 10 A

Measure the worn depth of the No. 1 chain vibration damper.

Maximum depth:

1.0 mm (0.0394 in.)


If the depth is more than the maximum, replace the No. 1 chain vibration damper.


Hide 13561 44.INSPECT NO. 2 CHAIN VIBRATION DAMPER

a.
A164587E01
2.643,1.196 3.051,1.368 0.408,0.172 10 Depth 0.456,0.46 0.579,0.612 0.123,0.151 10 A 1.867,1.93 2.122,2.081 0.254,0.151 10 A-A 1.563,1 1.686,1.151 0.123,0.151 10 A

Measure the worn depth of the No. 2 chain vibration damper.

Maximum depth:

1.0 mm (0.0394 in.)


If the depth is more than the maximum, replace the No. 2 chain vibration damper.


Hide 15708 45.INSPECT NO. 1 OIL NOZZLE SUB-ASSEMBLY

a.
A164609

Push the check valve with a pin to check if it is stuck.

If stuck, replace the No. 1 oil nozzle sub-assembly.


b.

Push the check valve with a pin to check if it moves smoothly.


c.
U162898E02
0.99,1.844 0.573,1.115 0.573,1.115 0.438,1.115 true 1.792,1 2.667,1.292 2.667,1.292 2.667,1.438 true 2.833,0.729 2.99,0.896 0.156,0.167 10 false B 0.271,1.031 0.427,1.198 0.156,0.167 10 false A 2.625,1.5 2.781,1.667 0.156,0.167 10 false C

While covering A, apply air into B. Check that air does not leak through C. Perform the check again while covering B and applying air into A.

If air leaks, clean or replace the No. 1 oil nozzle sub-assembly.


d.
U162899E02
0.99,1.844 0.573,1.115 0.573,1.115 0.448,1.115 true 1.813,1.01 2.792,1.323 2.792,1.323 2.792,1.417 true 2.802,0.781 2.958,0.948 0.156,0.167 10 false B 0.292,1.042 0.448,1.219 0.156,0.177 10 false A 2.75,1.458 2.906,1.625 0.156,0.167 10 false C

Push the check valve while covering A, and apply air into B. Check that air passes through C. Perform the check again while covering B, pushing the check valve and applying air into A.

If air does not pass through C, clean or replace the No. 1 oil nozzle sub-assembly.


Hide 17111 46.INSPECT NO. 1 INTAKE MANIFOLD FOR FLATNESS

a.
A164636E04
0.094,0.083 2.198,0.292 2.104,0.208 12 false No. 3 Intake Manifold Side: 0.094,1.823 1.74,2.021 1.646,0.198 12 false Cylinder Head Side:

Using a precision straightedge and feeler gauge, measure the warpage of the contact surface between the No. 1 and No. 3 intake manifold, and the No. 1 intake manifold and cylinder head.

Maximum Warpage:
Item Specified Condition
No. 3 intake manifold 0.10 mm (0.00394 in.)
Cylinder head 0.10 mm (0.00394 in.)


If the warpage is more than the maximum, replace the No. 1 intake manifold.


Hide 17112 47.INSPECT NO. 2 INTAKE MANIFOLD FOR FLATNESS

a.
A164636E04
0.094,0.083 2.198,0.292 2.104,0.208 12 false No. 3 Intake Manifold Side: 0.094,1.823 1.74,2.021 1.646,0.198 12 false Cylinder Head Side:

Using a precision straightedge and feeler gauge, measure the warpage of the contact surface between the No. 2 and No. 3 intake manifold, and the No. 2 intake manifold and cylinder head.

Maximum Warpage:
Item Specified Condition
No. 3 intake manifold 0.10 mm (0.00394 in.)
Cylinder head 0.10 mm (0.00394 in.)


If the warpage is more than the maximum, replace the No. 2 intake manifold.


Hide 17114D 48.INSPECT NO. 3 INTAKE MANIFOLD FOR FLATNESS

a.
A164637E03
0.125,1.292 1.469,1.563 1.344,0.271 12 false Intake Pipe Side: 0.104,3.458 1.708,3.667 1.604,0.208 12 false Intake Manifold Side:

Using a precision straightedge and feeler gauge, measure the warpage of the contact surface between the No. 3 and No. 1 intake manifold, the No. 3 and No. 2 intake manifold, and the No. 3 intake manifold and intake pipe.

Maximum Warpage:
Item Specified Condition
Intake pipe 0.10 mm (0.00394 in.)
No. 2 and No. 3 intake manifold 0.15 mm (0.00591 in.)


If the warpage is more than the maximum, replace the No. 3 intake manifold.


Hide 17141 49.INSPECT EXHAUST MANIFOLD FOR FLATNESS

a.
A164599E01
0.112,0.047 0.380,0.215 0.269,0.168 10 RH: 0.112,1.613 0.380,1.781 0.269,0.168 10 LH:

Using a precision straightedge and feeler gauge, measure the warpage of the contact surface between the exhaust manifold and cylinder head.

Maximum warpage:

0.80 mm (0.0315 in.)


If the warpage is more than the maximum, replace the exhaust manifold.