23250
1.INSTALL FUEL INJECTOR ASSEMBLY
Attach the 3 clamps to install the No. 6 wire harness to the delivery pipe sub-assembly RH.
Attach the 3 clamps to install the No. 7 wire harness to the delivery pipe sub-assembly LH.
Apply gasoline or spindle oil to a new O-ring and install it to the fuel injector assembly.
Make sure that there is no damage or foreign material in the groove of the injector when installing the O-ring.
Connect the fuel injector connector.
Install the fuel injector assembly to the delivery pipe as shown in the illustration.
| *a | CORRECT |
| *b | INCORRECT |
Make sure that there are no scratches or foreign matter in or around the insertion hole of the delivery pipe.
When inserting the fuel injector, be careful not to damage the O-ring.
Attach the part of the fuel injector labeled B between the parts of the delivery pipe labeled A.
Check that each injector is installed to the delivery pipe facing the direction shown in the illustration.
| *A | Fuel Delivery Pipe Sub-assembly RH | *B | Fuel Delivery Pipe Sub-assembly LH |
23808
2.INSTALL FUEL DELIVERY PIPE SUB-ASSEMBLY LH
Install the 2 delivery pipe spacers and 4 insulators to the cylinder head LH.
Install the delivery pipe (with injectors) to the cylinder head LH.
Install the 2 bolts.
Make sure that the part of the injector labeled B is between the parts of the delivery pipe labeled A.
| *1 | Delivery Pipe |
| *2 | Fuel Injector |
| *a | CORRECT |
| *b | INCORRECT |
Connect the No. 7 wire harness connector.
23807
3.INSTALL FUEL DELIVERY PIPE SUB-ASSEMBLY RH
Install the 2 delivery pipe spacers and 4 insulators to the cylinder head RH.
Install the delivery pipe (with injectors) to the cylinder head RH.
Install the 2 bolts.
Make sure that the part of the injector labeled B is between the parts of the delivery pipe labeled A.
| *1 | Delivery Pipe |
| *2 | Fuel Injector |
| *a | CORRECT |
| *b | INCORRECT |
Connect the No. 6 wire harness connector.
Connect the ventilation hose.
23271F
4.CONNECT NO. 1 FUEL HOSE
Connect the No. 1 fuel hose to the fuel delivery pipe sub-assembly LH (See page Engine / Hybrid System>3UR-FE (FUEL)>FUEL SYSTEM>PRECAUTION).
23901
5.CONNECT NO. 1 FUEL TUBE
LH Side:
Connect the No. 1 fuel tube to the delivery pipe sub-assembly LH (See page Engine / Hybrid System>3UR-FE (FUEL)>FUEL SYSTEM>PRECAUTION).
Connect the No. 1 fuel tube to the delivery pipe sub-assembly RH (for metallic type) (See page Engine / Hybrid System>3UR-FE (FUEL)>FUEL SYSTEM>PRECAUTION).
23902
6.CONNECT NO. 2 FUEL TUBE
Connect the No. 2 fuel tube to the fuel pressure regulator assembly (See page Engine / Hybrid System>3UR-FE (FUEL)>FUEL SYSTEM>PRECAUTION).
12601B
7.INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY
12613
8.INSTALL NO. 3 ENGINE COVER
17880
9.INSTALL AIR CLEANER HOSE ASSEMBLY
11209
10.INSTALL V-BANK COVER SUB-ASSEMBLY
11.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
12.INSPECT FOR FUEL LEAK
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG) and intelligent tester main switch on.
Do not start the engine.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.
Check that there are no fuel leaks after doing maintenance anywhere on the fuel system.
If DTC P1603 is output, clear the DTC (See page Engine / Hybrid System>3UR-FE (ENGINE CONTROL)>SFI SYSTEM(w/o Secondary Air Injection System)>P1603).