Home › Engine / Hybrid System › 3UR-FE (ENGINE MECHANICAL) › ENGINE ASSEMBLY › 2015.08–2017.08
RM2660E _51 Engine / Hybrid System _052777 3UR-FE ENGINE MECHANICAL _0255049 ENGINE ASSEMBLY A

3UR-FE ENGINE MECHANICAL  ENGINE ASSEMBLY  INSTALLATION  


PROCEDURE

Hide 12316A 1.INSTALL NO. 2 FRONT ENGINE MOUNTING BRACKET LH

a.

Install the No. 2 front engine mounting bracket LH with the bolt.

Torque:
32 N*m (326 kgf*cm, 24 ft.*lbf)


Hide 12361 2.INSTALL FRONT ENGINE MOUNTING INSULATOR RH

a.

Install the mounting insulator with the nut.

Torque:
72 N*m (734 kgf*cm, 53 ft.*lbf)


Hide 12362A 3.INSTALL FRONT ENGINE MOUNTING INSULATOR LH

a.

Install the mounting insulator with the nut.

Torque:
72 N*m (734 kgf*cm, 53 ft.*lbf)


Hide 4.REMOVE ENGINE STAND

a.
A236996

Install 2 engine hangers with 2 bolts as shown in the illustration.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)

HINT:
Engine hanger 12281-38150
Bolt 90119-14120



b.

Attach an engine sling device and hang the engine with a chain block.


c.

Remove the bolts and engine assembly from the engine stand.

NOTICE:
·

With the exception of installing the engine assembly to an engine stand or removing the engine assembly from an engine stand, do not perform any work on the engine while it is suspended, as doing so is dangerous.

·

Pay attention to the angle of the sling device as the engine assembly or engine hangers may be damaged or deformed if the angle is incorrect.




Hide 5.INSTALL ENGINE ASSEMBLY

a.

Slowly lower the engine assembly into the engine compartment.

NOTICE:

Make sure that the engine is clear of all wiring and hoses.



b.

Attach the engine mounting insulators to the vehicle.


c.

Install the 4 engine mounting insulator bolts.

Torque:
79 N*m (806 kgf*cm, 58 ft.*lbf)


d.

Remove the 2 bolts and 2 engine hangers.


Hide 6.INSTALL WATER PIPE AND HOSE SUB-ASSEMBLY

a.

Connect the hose and install the water pipe and hose with the 2 bolts.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


Hide 32907A 7.CONNECT OIL COOLER PIPE ASSEMBLY

a.

Connect the oil cooler pipe with the 2 bolts.

Torque:
14 N*m (143 kgf*cm, 10 ft.*lbf)


Hide 32101 8.INSTALL DRIVE PLATE AND RING GEAR SUB-ASSEMBLY

a.
A163778E07
0.844,1.219 0.844,1.76 0.844,1.76 1.25,1.76 false 1.083,1.052 1.083,1.75 false 1.292,1.667 1.688,1.917 0.396,0.25 10 false SST

Using SST, hold the crankshaft.

SST
09213-70011  
09330-00021  


b.
A239173

Install the crankshaft angle sensor rotor.

Text in Illustration
V100135

Engine Side

HINT:
·

Align the pin hole of the crankshaft angle sensor rotor with the pin of the crankshaft.

·

As the crankshaft angle sensor rotor is not reversible, be sure to install it so that it is facing in the direction shown in the illustration.




c.
A237717E01
0.704,0.681 0.878,0.868 0.174,0.187 10 *1 3.094,2.879 3.284,3.066 0.191,0.187 10 *2 0.907,0.766 1.064,0.766 1.064,0.766 1.508,1.078 false 3.08,2.974 2.94,2.974 2.94,2.974 2.622,3.389 false

Install the drive plate and rear drive plate spacer onto the crankshaft.

Text in Illustration
*1 Drive Plate
*2 Rear Drive Plate Spacer
V100135

Automatic Transmission Side

HINT:

As the rear drive plate spacer and the drive plate are not reversible, be sure to install them so that they are facing in the direction shown in the illustration.



d.

Install the drive plate and ring gear and bolts.

HINT:

The bolts are tightened in 2 progressive steps.


i.

Clean the bolts and bolt holes.


ii.
A192239E03
1.374,0.672 1.576,0.827 0.202,0.156 10 *1 1.569,0.758 1.672,0.758 1.672,0.758 1.821,1.24 false

Apply adhesive to 2 or 3 threads at the end of each of the 10 bolts.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent


Text in Illustration
*1 Adhesive


iii.
A238248E02
1.302,0.51 1.406,0.656 0.104,0.146 10 true 9 1.677,0.406 1.771,0.563 0.094,0.156 10 true 1 1.688,1.667 1.781,1.844 0.094,0.177 10 true 2 2.26,0.854 2.375,1 0.115,0.146 10 true 3 1.094,1.219 1.188,1.375 0.094,0.156 10 true 4 2.271,1.26 2.385,1.406 0.115,0.146 10 true 5 1.094,0.865 1.208,1.021 0.115,0.156 10 true 6 2.073,0.531 2.198,0.688 0.125,0.156 10 true 7 1.281,1.563 1.375,1.708 0.094,0.146 10 true 8 2.021,1.563 2.198,1.708 0.177,0.146 10 true 10

Step 1:

Install and uniformly tighten 10 new bolts in the sequence shown in the illustration.

Torque:
30 N*m (301 kgf*cm, 22 ft.*lbf)

NOTICE:
·

Do not reuse the drive plate installation bolts.

·

Do not strike or damage the drive plate installation bolts. Be sure to handle them carefully.




iv.

Mark the upside of each drive plate installation bolt with paint.


v.

Step 2:

Tighten the cylinder head bolts another 90°.


vi.

Check that the painted marks are now at a 90° angle to the upside.

NOTICE:

Do not start the engine for at least an hour after installing the drive plate.




Hide 12371 9.INSTALL REAR NO. 1 ENGINE MOUNTING INSULATOR

HINT:

Only perform this procedure when replacement of the engine mounting insulator is necessary.


a.

Install the rear engine mounting insulator to the transmission with the 4 bolts.

Torque:
59 N*m (602 kgf*cm, 44 ft.*lbf)


b.

Install the front engine mounting insulator RH with the 2 bolts.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 17104 13.INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY RH

Hide 17167 14.INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

Hide 17105 16.INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY LH

Hide 17168 17.INSTALL NO. 2 EXHAUST MANIFOLD HEAT INSULATOR

Hide 37110 20.INSTALL REAR PROPELLER SHAFT ASSEMBLY

Hide 37140 21.INSTALL FRONT PROPELLER SHAFT ASSEMBLY

Hide 11452 22.INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE

a.

Apply a light coat of engine oil to a new O-ring.


b.

Install the O-ring to the guide.


c.

Install the dipstick guide with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


d.

Install the dipstick.


e.

Connect the wire harness clamp.


Hide 17450B 24.INSTALL FRONT NO. 2 EXHAUST PIPE ASSEMBLY

Hide 88320 29.CONNECT COOLER COMPRESSOR ASSEMBLY

Hide 30.CONNECT WIRE HARNESS AND HOSE

a.

w/ Winch:

Attach the wire harness clamp and connect the ground wire to the wire harness clamp bracket with the nut.

Torque:
19 N*m (195 kgf*cm, 14 ft.*lbf)


b.

Connect the 2 connectors and 2 clamps.


c.

Connect the 2 connectors and 2 clips to the engine room junction block.


d.

Install the engine wire to the engine room junction block with the nut. Then connect the 2 clips.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


e.

Install the ground wire to the body with the bolt.

Torque:
for Type A : 8.4 N*m (86 kgf*cm, 74 in.*lbf)
for Type B : 10 N*m (102 kgf*cm, 7 ft.*lbf)

HINT:
A418191C01
0.375,0.219 0.688,0.375 0.313,0.156 10 false *A 2.135,0.219 2.448,0.375 0.313,0.156 10 false *B
*A for Type A
*B for Type B


Type A or B can be distinguished by confirming the mark on the bolt.



f.

Connect the clamp.


g.

Connect the cable to the positive (+) battery terminal.


h.

Install the wire to the positive (+) battery cable with the nut.

Torque:
7.6 N*m (77 kgf*cm, 67 in.*lbf)


i.

Install the ground wire with the bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


j.

Connect the clip and 5 connectors to the connector holder block.


k.

Install the heater hose.


l.

Connect the ECM connector and clamp.

HINT:

Refer to the following procedures to connect the ECM connector (See page Engine / Hybrid System>3UR-FE (ENGINE CONTROL)>ECM>INSTALLATION).



m.

Connect the purge line hose.


Hide 23801P 31.CONNECT FUEL MAIN AND RETURN HOSE

a.

Connect the fuel main and return hoses (See page Engine / Hybrid System>3UR-FE (FUEL)>FUEL SYSTEM>PRECAUTION).


b.

Install the fuel pipe clamp.


Hide 16572D 34.INSTALL NO. 2 RADIATOR HOSE

Hide 16571C 35.INSTALL NO. 1 RADIATOR HOSE

Hide 17700 36.INSTALL AIR CLEANER ASSEMBLY

a.

Install the air cleaner with the 3 bolts.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


Hide 40.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 11209 46.INSTALL V-BANK COVER SUB-ASSEMBLY

a.
A177597E05
1.667,0.427 1.875,0.427 1.875,0.427 2.219,0.573 false 1.729,0.125 1.948,0.125 1.948,0.125 2.51,0.49 false 0.896,2.781 1.479,3.042 1.479,3.042 1.479,3.146 false 0.406,2.927 0.563,2.927 false 1.5,0.052 1.698,0.24 0.198,0.188 10 false *1 1.479,0.354 1.656,0.552 0.177,0.198 10 false *2 1.396,3.146 1.573,3.323 0.177,0.177 10 false *4 0.198,2.854 0.375,3.021 0.177,0.167 10 false *3

Attach the 2 V-bank cover hooks to the bracket. Then align the 3 V-bank cover grommets with the 3 pins, and press down on the V-bank cover to attach the pins.

Text in Illustration
*1 Bracket
*2 Hook
*3 Pin
*4 Grommet


Hide 51442 48.INSTALL NO. 2 ENGINE UNDER COVER

a.

Install the No. 2 engine under cover with the 2 bolts.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)


Hide 51405A 49.INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

a.

Install the No. 1 engine under cover with the 10 bolts.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)


Hide 53738A 50.INSTALL FRONT FENDER APRON SEAL REAR RH

Hide 53736G 51.INSTALL FRONT FENDER APRON SEAL FRONT RH

Hide 53739A 52.INSTALL FRONT FENDER APRON SEAL REAR LH

Hide 55781E 54.INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

Hide 53301 55.INSTALL HOOD SUB-ASSEMBLY

a.

Install the hood with the 4 bolts.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


b.

Connect the 2 hood supports with the 2 hood support bolts.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)

CAUTION:

Install the hood support while supporting the hood by hand.


NOTICE:

Check that the hood support is engaged in the ball joint and that it cannot be pulled out.



Hide 53301 56.ADJUST HOOD SUB-ASSEMBLY

Hide 53294C 57.INSTALL RADIATOR SIDE DEFLECTOR LH

Hide 32917 58.INSTALL TRANSMISSION OIL COOLER AIR DUCT