Home › Engine / Hybrid System › 1VD-FTV (FUEL) › FUEL SUPPLY PUMP › from 2015.08
RM2660E _51 Engine / Hybrid System _052783 1VD-FTV FUEL _0255110 FUEL SUPPLY PUMP A

1VD-FTV FUEL  FUEL SUPPLY PUMP  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the injectors (including shuffling the injectors between the cylinders), common rail, cylinder head or intake manifold, it is necessary to replace the injection pipes with new ones.

·

w/ DPF:

When fuel lines are disconnected, air may enter the fuel lines, leading to engine starting trouble. Therefore, perform forced regeneration and bleed the air from the fuel lines (See page Engine / Hybrid System>1VD-FTV (EMISSION CONTROL)>EMISSION CONTROL SYSTEM>ON-VEHICLE INSPECTION).



PROCEDURE

Hide 22100 1.INSTALL FUEL SUPPLY PUMP

NOTICE:

Do not push the supply pump drive gear.


a.
A164258E02
0.429,0.761 0.578,0.934 0.149,0.172 10 *1 0.617,0.862 0.784,0.862 0.784,0.862 1.034,1.398 false

Install a new O-ring to the supply pump.

Text in Illustration
*1 New O-Ring


b.

Apply a light coat of engine oil to the O-ring.


c.
A164817

Using an 8 mm x 1.25 pitch tap, remove the adhesive from the timing gear case bolt hole.


d.
A165070E03
2.644,0.842 2.811,0.990 0.166,0.149 10 *1 2.747,0.57 2.747,0.825 false

Apply adhesive to 2 or more threads as shown in the illustration.

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent


Text in Illustration
*1 Adhesive


e.
A164256E04
1.104,0.167 1.26,0.167 1.26,0.167 1.594,0.688 true 2.969,0.656 2.802,0.656 2.802,0.656 2.656,1.552 true 0.917,0.063 1.115,0.281 0.198,0.219 10 true *a 3.01,0.563 3.375,0.813 0.365,0.25 10 true *b

Align the set key on the drive shaft with the groove of the supply pump drive gear.

Text in Illustration
*a Groove
*b Set Key

NOTICE:

Do not hold the supply pump by the parts indicated by the arrows in the illustration, as this may result in deformation, damage and fuel leakage.



f.

Temporarily install the fuel supply pump with the 2 nuts.


g.

Using a 6 mm hexagon wrench, install the bolt.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


h.

Tighten the 2 nuts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


i.

Using a wrench, hold the crankshaft.


j.

Install the set nut.

Torque:
68 N*m (693 kgf*cm, 50 ft.*lbf)


k.

Turn the crankshaft 2 times, and check that there are no problems.


l.
A164255

Using a dial indicator, check the thrust clearance of the supply pump drive shaft while moving the pump drive shaft gear back and forth.

Standard thrust clearance:

0.05 to 0.30 mm (0.00197 to 0.0118 in.)


If the clearance is not within the specified range, disassemble and reassemble the supply pump and pump drive shaft gear. Then repeat the step above.


m.

Connect the fuel temperature sensor connector.


Hide 23811G 2.INSTALL NO. 1 FUEL PIPE

a.

Install 2 new gaskets and the No. 1 fuel pipe with the union bolt.

Torque:
17 N*m (175 kgf*cm, 13 ft.*lbf)


Hide 11324 3.INSTALL TIMING CHAIN COVER PLATE

a.

Install a new gasket and the cover plate with the 4 bolts.

Torque:
9.1 N*m (93 kgf*cm, 81 in.*lbf)


Hide 11336A 4.INSTALL TIMING GEAR COVER INSULATOR (w/ Intercooler)

Hide 16268 6.INSTALL NO. 1 WATER BY-PASS PIPE

Hide 23920A 7.INSTALL FUEL COOLER ASSEMBLY (w/o DPF)

Hide 25620 9.INSTALL EGR VALVE ASSEMBLY WITH EGR COOLER (w/ EGR System)

Hide 10.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


a.

Connect the cables to the negative (-) main battery and sub-battery terminals.


Hide 11.PERFORM FUEL SUPPLY PUMP INITIALIZATION