Home › Engine / Hybrid System › 1VD-FTV (ENGINE MECHANICAL) › ENGINE UNIT
RM2660E _51 Engine / Hybrid System _052779 1VD-FTV ENGINE MECHANICAL _0255065 ENGINE UNIT A

1VD-FTV ENGINE MECHANICAL  ENGINE UNIT  INSTALLATION  


PROCEDURE

Hide 12502 3.INSTALL COMPRESSOR BRACKET

a.

Install the compressor bracket with the bolt.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 16620D 4.INSTALL V-RIBBED BELT TENSIONER ASSEMBLY

Hide 12158 5.INSTALL STIFFENER INSULATOR RH (w/ Intercooler)

Hide 15320B 6.INSTALL OIL PRESSURE REGULATOR ASSEMBLY

a.
U163070E01
1.127,0.368 1.281,0.539 0.154,0.171 10 A 1.127,2.656 1.281,2.827 0.154,0.171 10 B 3.039,1.606 3.193,1.778 0.154,0.171 10 C 1.062,2.744 0.916,2.744 false

Hold the oil pressure regulator body in a vise between aluminum plates.


b.

Apply a light coat of engine oil to the oil pump relief valve labeled C.


c.

Install the oil pump relief valve labeled C to the oil pressure regulator body.


d.

Install the 2 springs labeled B to the oil pressure regulator body.


e.

Using a 10 mm hexagon wrench, install a new gasket and the oil pump relief valve plug labeled A.

Torque:
50 N*m (510 kgf*cm, 37 ft.*lbf)


f.

Apply a light coat of engine oil to a new O-ring, and install it to the oil pressure regulator body.


g.

Using a 26 mm wrench, install a new gasket and the oil pressure regulator.

Torque:
86 N*m (877 kgf*cm, 63 ft.*lbf)


Hide 15609J 7.INSTALL OIL FILTER BRACKET DRAIN COCK ASSEMBLY

a.
A181686E01
1.265,2.305 1.512,2.480 0.247,0.175 10 30° 1.821,2.305 2.067,2.480 0.247,0.175 10 30°

Install the drain cock.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


b.

Using a 17 mm wrench, rotate the drain cock clockwise (360°) and align the position of the drain hole so that it is within the range shown in the illustration after tightening the drain cock to the specified torque.

NOTICE:
·

As the oil filter bracket may be damaged, the maximum tightening torque should be 80 N*m (816 kgf*cm, 59 ft.*lbf) or less.

·

Do not rotate the drain cock more than 1 revolution (360°) after tightening the drain cock with the specified torque.

·

Do not expose the drain cock to coolant within 1 hour after installation.




c.

Install the oil filter drain cock plug.

Torque:
13 N*m (130 kgf*cm, 9 ft.*lbf)


Hide 15387A 8.INSTALL OIL TANK BRACKET

a.

Install the oil tank bracket with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 12582 9.INSTALL NO. 2 CYLINDER BLOCK INSULATOR

Hide 12325A 10.INSTALL ENGINE MOUNTING BRACKET LH

a.

Install the engine mounting bracket LH with the 4 bolts.

Torque:
80 N*m (816 kgf*cm, 59 ft.*lbf)


Hide 16207 11.INSTALL NO. 2 WATER BY-PASS PIPE SUB-ASSEMBLY

a.
U163069E02
2.781,1.177 2.958,1.344 0.177,0.167 10 false 1 1.26,0.292 1.438,0.458 0.177,0.167 10 false 2 0.333,1.833 0.51,2 0.177,0.167 10 false 3

Temporarily install a new gasket and No. 2 water by-pass pipe with the union bolt and 2 bolts.


b.

Tighten the union bolt and 2 bolts of the No. 2 water by-pass pipe in the order shown in the illustration.

Torque:
for union bolt : 35 N*m (357 kgf*cm, 26 ft.*lbf)
for bolt : 10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 25708 12.INSTALL NO. 3 VACUUM TRANSMITTING PIPE SUB-ASSEMBLY

a.

Install the No. 3 vacuum transmitting pipe with the 2 bolts.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)


b.

w/ Intercooler:

Connect the vacuum hose.


Hide 1723A 13.INSTALL TURBOCHARGER WIRE

a.

Install the turbocharger wire with the 2 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


b.

Attach the 3 wire harness clamps.


Hide 17873 14.INSTALL NO. 2 INTAKE AIR CONNECTOR BRACKET

a.

Install the No. 2 intake air connector bracket with the bolt.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


b.

Attach the 2 wire clamps.


Hide 12581 15.INSTALL NO. 1 CYLINDER BLOCK INSULATOR

Hide 12315A 16.INSTALL ENGINE MOUNTING BRACKET RH

a.

Install the engine mounting bracket RH with the 4 bolts.

Torque:
80 N*m (816 kgf*cm, 59 ft.*lbf)


Hide 25709E 17.INSTALL NO. 4 VACUUM TRANSMITTING PIPE SUB-ASSEMBLY (w/ Intercooler)

a.

Install the No. 4 vacuum transmitting pipe with the 2 bolts.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)


b.

Connect the vacuum hose.


Hide 16206 18.INSTALL NO. 1 WATER BY-PASS PIPE SUB-ASSEMBLY

a.

Temporarily install a new gasket and the No. 1 water by-pass pipe with the union bolt and bolt.


b.
U163068E02
0.771,0.438 0.948,0.604 0.177,0.167 10 false 1 2.979,0.094 3.156,0.26 0.177,0.167 10 false 2

Tighten the union bolt and bolt of the No. 1 water by-pass pipe in the order shown in the illustration.

Torque:
for union bolt : 35 N*m (357 kgf*cm, 26 ft.*lbf)
for bolt : 10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 17368B 19.INSTALL AIR TUBE SUPPORT

a.

Install the air tube support with the 2 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 17872 20.INSTALL NO. 1 INTAKE AIR CONNECTOR BRACKET

a.

Install the No. 1 intake air connector bracket with the 2 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 11181 21.INSTALL REAR CYLINDER HEAD PLATE LH (w/o EGR System)

a.

Install a new gasket and the rear cylinder head plate LH with the 2 bolts.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)

HINT:

The gasket claw should face toward the plate.



Hide 22.INSTALL REAR CYLINDER HEAD PLATE RH (w/o EGR System)

a.

Install a new gasket and the rear cylinder head plate RH with the 2 bolts.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)

HINT:

The gasket claw should face toward the plate.



Hide 11225 23.INSTALL CYLINDER HEAD COVER SILENCER LH (w/o DPF)

a.

w/ Intercooler:

Install the cylinder head cover silencer LH with the 3 bolts.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


Hide 11224 24.INSTALL CYLINDER HEAD COVER SILENCER RH (w/o DPF)

a.

w/ Intercooler:

Install the cylinder head cover silencer RH with the 3 bolts.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


Hide 25706 25.INSTALL NO. 1 VACUUM TRANSMITTING PIPE SUB-ASSEMBLY (w/o DPF)

Hide 25860 26.INSTALL NO. 1 VACUUM SWITCHING VALVE ASSEMBLY (w/o DPF)

Hide 16307A 27.INSTALL FAN BRACKET SUB-ASSEMBLY

Hide 28.INSTALL NO. 2 IDLER PULLEY BRACKET (w/ Viscous Heater)

Hide 16630H 29.INSTALL NO. 2 IDLER PULLEY (w/ Viscous Heater)

Hide 30.INSTALL NO. 3 ENGINE HANGER

a.

Install the No. 3 engine hanger with the 2 bolts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


Hide 17945 31.INSTALL NO. 1 INTERCOOLER SUPPORT BRACKET

a.

Install the No. 1 intercooler support bracket with the 2 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 23243C 32.INSTALL FUEL PUMP MOTOR WIRE

a.
A174812

Install the fuel pump wire with the bolt.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)

HINT:

Attach the claw of the bracket to the timing gear case when installing the bracket.



Hide 19871 34.INSTALL NO. 1 GLOW PLUG CONNECTOR

Hide 31484 35.INSTALL CLUTCH FLEXIBLE HOSE BRACKET (for Manual Transmission)

a.

Install the clutch flexible hose bracket with the 2 bolts.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


Hide 16332 36.INSTALL NO. 1 AND NO. 2 WATER OUTLET PIPES AND WATER BY-PASS OUTLET

a.

Align the painted mark of the No. 1 water hose joint with the protrusion of the water by-pass outlet and connect the water by-pass outlet to the No. 1 water hose joint.


b.

Align the painted mark of the No. 1 water hose joint with the painted mark of the No. 2 water outlet pipe and connect the No. 2 water outlet pipe to the No. 1 water hose joint.


c.

Connect a new gasket and the No. 1 and No. 2 water outlet pipes with the 2 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)

HINT:

The gasket claws can face the No. 1 or No. 2 water outlet pipe.



Hide 37.INSTALL WATER OUTLET PIPE

a.

Install 2 new gaskets and the water outlet pipe with the 4 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)

HINT:

The gasket claw should face toward the water outlet pipe.



Hide 16331 38.INSTALL WATER OUTLET

a.

Install a new gasket and the water outlet with the 2 bolts, and then connect the water outlet to the No. 2 water hose joint.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 17946 39.INSTALL NO. 2 INTERCOOLER SUPPORT BRACKET

a.

Install the No. 2 intercooler support bracket with the 2 bolts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


Hide 16262 41.CONNECT INLET WATER HOSE

Hide 11336A 44.INSTALL TIMING GEAR COVER INSULATOR (w/ Intercooler)

a.

w/o Viscous Heater:

Install the timing gear cover insulator with the 2 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


b.

w/ Viscous Heater:

Install the timing gear cover insulator.


Hide 47.INSTALL NO. 1 IDLER PULLEY BRACKET (w/ Viscous Heater)

Hide 87120G 48.INSTALL VISCOUS HEATER ASSEMBLY WITH MAGNET CLUTCH (w/ Viscous Heater)

Hide 17208 49.INSTALL NO. 2 TURBOCHARGER SUB-ASSEMBLY WITH EXHAUST MANIFOLD LH

Hide 16287 57.INSTALL NO. 2 TURBO WATER HOSE

Hide 12263 59.INSTALL NO. 3 VENTILATION HOSE

Hide 17201 60.INSTALL NO. 1 TURBOCHARGER SUB-ASSEMBLY WITH EXHAUST MANIFOLD RH

Hide 15474A 64.CONNECT NO. 1 OUTLET TURBO OIL HOSE

Hide 16285 66.INSTALL NO. 2 TURBO WATER HOSE

Hide 12262 68.INSTALL NO. 2 VENTILATION HOSE

Hide 29300 72.INSTALL VACUUM PUMP ASSEMBLY (w/ Intercooler)