Home › Engine / Hybrid System › 1GR-FE (INTAKE / EXHAUST) › EXHAUST PIPE
RM2660E _51 Engine / Hybrid System _052791 1GR-FE INTAKE / EXHAUST _0255178 EXHAUST PIPE A

1GR-FE INTAKE / EXHAUST  EXHAUST PIPE  INSTALLATION  


PROCEDURE

Hide 17410 1.INSTALL FRONT EXHAUST PIPE ASSEMBLY

a.

Install a new gasket and the front exhaust pipe to the exhaust manifold RH with 2 new nuts.

Torque:
54 N*m (554 kgf*cm, 40 ft.*lbf)


b.

Connect the heated oxygen sensor connector.


Hide 89465A 2.INSTALL HEATED OXYGEN SENSOR (for Bank 2 Sensor 2)

Hide 17450B 3.INSTALL FRONT NO. 2 EXHAUST PIPE ASSEMBLY

a.

Install a new gasket and the front No. 2 exhaust pipe to the exhaust manifold LH with 2 new nuts.

Torque:
54 N*m (554 kgf*cm, 40 ft.*lbf)


b.
A181385E02
1.198,0.677 1.344,0.677 1.344,0.677 1.719,1.01 true 1.292,2.958 1.448,2.958 1.448,2.958 1.823,3.313 true 0.083,0.094 2.271,0.49 2.188,0.396 12 true for Automatic Transmission: 0.073,2.354 2.198,2.698 2.125,0.344 12 true for Manual Transmission: 0.646,0.594 1.208,0.781 0.563,0.188 10 true Bracket 0.688,2.885 1.271,3.083 0.583,0.198 10 true Bracket

Connect the heated oxygen sensor connector.

HINT:

Hook the wire harness to the bracket.



Hide 17420 4.INSTALL CENTER EXHAUST PIPE ASSEMBLY

a.
A128853

Check the free length.

i.

Using a vernier caliper, measure the free length of the compression spring.

Minimum free length:

43 mm (1.693 in.)


If the free length is less than the minimum, replace the compression spring.



b.

Connect the center exhaust pipe to the 3 exhaust pipe supports.


c.

Install 2 new gaskets to the front exhaust pipe and front No. 2 exhaust pipe.


d.

Install the center exhaust pipe with the 4 bolts and 2 compression springs.

Torque:
for center exhaust pipe and front exhaust pipe : 43 N*m (438 kgf*cm, 32 ft.*lbf)
for center exhaust pipe and front No. 2 exhaust pipe : 48 N*m (489 kgf*cm, 35 ft.*lbf)


Hide 17430 5.INSTALL TAILPIPE ASSEMBLY

a.

Install the tailpipe to the 2 exhaust pipe supports.


b.

Set a new gasket to the center exhaust pipe.


c.
A167906E08
1.729,3.469 1.01,3.719 1.01,3.719 0.844,3.719 true 2.615,0.427 2.854,0.573 0.24,0.146 10 false 30° 0.271,1.031 0.823,1.177 0.552,0.146 10 false LH Side 0.719,0.167 1.146,0.344 0.427,0.177 10 false Upper 0.104,2.854 0.469,3.01 0.365,0.156 10 false Front 0.333,3.615 0.823,3.771 0.49,0.156 10 false Gasket

Connect the tailpipe to the center pipe with a new clamp.

Torque:
32 N*m (326 kgf*cm, 24 ft.*lbf)

HINT:

Install the clamp within the angle range shown in the illustration.



Hide 89465 6.INSTALL HEATED OXYGEN SENSOR (for Bank 1 Sensor 2)