Home › Engine / Hybrid System › 1VD-FTV (COOLING) › COOLANT
RM2660E _51 Engine / Hybrid System _052795 1VD-FTV COOLING _0255197 COOLANT A

1VD-FTV COOLING  COOLANT  REPLACEMENT  


PROCEDURE

Hide 53806 1.REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH

Hide 53805 2.REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH

Hide 51405A 3.REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

Hide 53292A 4.REMOVE UPPER RADIATOR SUPPORT SEAL

a.

Remove the 7 clips and upper radiator support seal.


Hide 5.DRAIN ENGINE COOLANT

CAUTION:

Do not remove the radiator reservoir cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.


HINT:

Collect the coolant in a container and dispose of it according to the regulations in your area.


a.

Loosen the radiator drain cock plug.


b.

Remove the radiator reservoir cap to drain the coolant in the radiator.


c.

Loosen the oil filter bracket drain cock plug to drain the coolant in the engine.

A174741E03
3.958,3.5 2.99,3.5 true 3.927,3.167 2.323,3.167 true 3.833,1.448 1.708,1.448 true 3.719,1.76 1.406,1.76 true 4.823,1.031 5.51,0.208 5.51,0.208 5.656,0.208 true 3.01,1.021 1.594,1.021 true 4.604,1.354 5.875,1.354 true 4.385,2.677 5.385,2.979 5.385,2.979 5.531,2.979 true 3.813,2.271 1.854,2.271 true 1.406,3.406 3.042,3.583 1.635,0.177 10 false Radiator Drain Cock Plug 1.01,3.083 2.302,3.229 1.292,0.146 10 false No. 2 Radiator Hose 5.604,2.896 7.031,3.24 1.427,0.344 10 false Oil Filter Bracket Drain Cock Plug 0.177,1.677 1.375,1.844 1.198,0.167 10 false Radiator Reservoir 0.177,1.354 1.667,1.531 1.49,0.177 10 false Radiator Reservoir Cap 5.729,0.135 7.021,0.281 1.292,0.146 10 false No. 1 Radiator Hose 5.927,1.281 6.563,1.458 0.635,0.177 10 false Vent Plug 0.177,0.927 1.552,1.115 1.375,0.188 10 false Engine Air Bleed Cap 0.177,2.188 1.865,2.344 1.688,0.156 10 false No. 2 Water By-pass Hose


d.

Tighten the radiator drain cock plug by hand.


e.
A177208

Tighten the oil filter bracket drain cock plug.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


Hide 6.ADD ENGINE COOLANT

a.
A179103

Remove the engine air bleed cap.


b.
A185226

Connect a clear hose to the engine air bleed pipe.


c.
A177426

Using a wrench, remove the vent plug.


d.
A177425

Fill the radiator with TOYOTA SLLC to the radiator reservoir filler neck.

HINT:

Pour TOYOTA SLLC until it spills out of the engine air bleed pipe.


Standard Capacity (for Automatic Transmission):
Item Specified Condition
Front heater only 14.8 liters (15.6 US qts, 13.0 Imp. qts)
Front heater and rear heater 17.6 liters (18.6 US qts, 15.5 Imp. qts)
Front heater with viscous heater 15.2 liters (16.1 US qts, 13.4 Imp. qts)
Front heater and rear heater with viscous heater 18.0 liters (19.0 US qts, 15.4 Imp. qts)


Standard capacity (for Manual Transmission):

15.4 liters (16.3 US qts, 13.5 Imp. qts)


NOTICE:

Do not substitute plain water for engine coolant.


HINT:

TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).



e.
A177426

Install the vent plug.

Torque:
2.0 N*m (20 kgf*cm, 18 in.*lbf)

NOTICE:

Do not tighten the plug to 5.0 N*m (51 kgf*cm, 44 in.*lbf) or more, as the plug will be damaged.



f.
A185226

Disconnect the clear hose from the engine air bleed pipe.


g.
A179103

Install the engine air bleed cap when coolant comes out.


h.

Install the radiator reservoir cap.


i.

Start the engine.

NOTICE:

Immediately after starting the engine, if the radiator reservoir does not have any coolant, perform the following: 1) stop the engine, 2) wait until the coolant has cooled down, and 3) add coolant until the coolant is filled to the FULL line.



j.

Maintain an engine speed of 3000 rpm for approximately 10 minutes so that the thermostat opens and air bleeding is performed.

CAUTION:
When pressing the radiator hoses:
·

Wear protective gloves.

·

Be careful as the radiator hoses are hot.

·

Keep your hands away from the radiator fan



NOTICE:
·

Pay attention to the needle of the water temperature meter. Make sure that the needle does not show an abnormally high temperature.

·

If there is not enough coolant, the engine may burn out or overheat.



HINT:

The thermostat opening timing can be confirmed by pressing the No. 2 radiator hose by hand, and checking when the engine coolant starts to flow inside the hose.



k.

Stop the engine, and wait until the engine coolant cools down to ambient temperature.

CAUTION:

Do not remove the radiator reservoir cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.



l.
A174740

Check that the coolant level is between the FULL and LOW lines.

If the coolant level is above the FULL line, drain coolant so that the coolant level is between the FULL and LOW lines.


Hide 53292A 8.INSTALL UPPER RADIATOR SUPPORT SEAL

a.

Install the upper radiator support seal with the 7 clips.


Hide 51405A 9.INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

Hide 53805 10.INSTALL FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH

Hide 53806 11.INSTALL FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH