w/ DPF:
When fuel lines are disconnected, air may enter the fuel lines, leading to engine starting trouble. Therefore, perform forced regeneration and bleed the air from the fuel lines (See page Engine / Hybrid System>1VD-FTV (EMISSION CONTROL)>EMISSION CONTROL SYSTEM>ON-VEHICLE INSPECTION).
12362A
1.INSTALL FRONT ENGINE MOUNTING INSULATOR LH
12361
2.INSTALL FRONT ENGINE MOUNTING INSULATOR RH
12281A
3.INSTALL NO. 1 AND NO. 2 ENGINE HANGER
4.REMOVE ENGINE STAND
Attach an engine sling device and hang the engine with a chain block.
Lift the engine, and remove it from the engine stand.
With the exception of installing the engine assembly to an engine stand or removing the engine assembly from an engine stand, do not perform any work on the engine while it is suspended, as doing so is dangerous.
Pay attention to the angle of the sling device as the engine assembly or engine hangers may be damaged or deformed if the angle is incorrect.
32101
5.INSTALL DRIVE PLATE AND RING GEAR SUB-ASSEMBLY (for Automatic Transmission)
Using a wrench, hold the crankshaft.
Install the rear crankshaft balancer weight.
|
Engine Side |
Align the pin hole of the rear crankshaft balancer weight with the pin of the crankshaft.
As the rear crankshaft balancer weight is not reversible, be sure to install it so that it is facing in the direction shown in the illustration.
Install the drive plate and ring gear and rear drive plate spacer with 8 new bolts.
| *1 | Drive Plate and Ring Gear |
| *2 | Rear Drive Plate Spacer |
|
Automatic Transmission Side |
As the drive plate and ring gear and rear drive plate spacer are not reversible, be sure to install them so that they are facing in the direction shown in the illustration.
Install and uniformly tighten the 8 bolts in the sequence shown in the illustration.
13405
6.INSTALL FLYWHEEL SUB-ASSEMBLY (for Manual Transmission)
Temporarily install the flywheel with 8 new bolts.
Align the crankshaft knock pin and flywheel knock pin hole.
Do not strike or damage the flywheel installation bolts. Be sure to handle them carefully.
Make sure there is no oil on the bolts.
Using a wrench, hold the crankshaft.
Uniformly install and tighten the 8 bolts in the sequence shown in the illustration.
31250
7.INSTALL CLUTCH DISC ASSEMBLY (for Manual Transmission)
31210
8.INSTALL CLUTCH COVER ASSEMBLY (for Manual Transmission)
9.INSTALL ENGINE ASSEMBLY
Slowly lower the engine into the engine compartment.
Install the 4 bolts to the front mounting insulator RH and LH.
Remove the 4 bolts and No. 1 and No. 2 engine hangers.
31482
10.INSTALL CLUTCH RELEASE CYLINDER TO FLEXIBLE HOSE TUBE (for Manual Transmission)
Install the clutch release cylinder to flexible hose tube with the bolt.
33030
11.INSTALL MANUAL TRANSMISSION UNIT ASSEMBLY
35000
12.INSTALL AUTOMATIC TRANSMISSION ASSEMBLY
17112
13.INSTALL NO. 2 INTAKE MANIFOLD
17111
14.INSTALL NO. 1 INTAKE MANIFOLD
23841C
15.INSTALL NO. 1 FUEL PIPE CLAMP (w/ DPF)
23881D
16.INSTALL FUEL HOSE BRACKET (w/ DPF)
23761A
17.INSTALL NO. 1 NOZZLE LEAKAGE PIPE (w/ DPF)
23762B
18.INSTALL NO. 2 NOZZLE LEAKAGE PIPE (w/ DPF)
16268
19.INSTALL NO. 1 WATER BY-PASS PIPE
23901H
20.INSTALL FUEL TUBE SUB-ASSEMBLY (w/ DPF)
23920A
21.INSTALL FUEL COOLER ASSEMBLY (w/o DPF)
16283
22.CONNECT NO. 6 WATER BY-PASS HOSE (w/o DPF)
23764A
23.INSTALL NO. 4 NOZZLE LEAKAGE PIPE (w/o DPF)
23763
24.INSTALL NO. 3 NOZZLE LEAKAGE PIPE (w/o DPF)
25689
25.INSTALL EGR COOLER INSULATOR (w/ EGR System)
25620
26.INSTALL EGR VALVE ASSEMBLY WITH EGR COOLER (w/ EGR System)
25615A
27.INSTALL EGR PIPE INSULATOR (w/ EGR System)
17853B
28.INSTALL INTAKE MANIFOLD INSULATOR (w/ EGR System)
17114D
29.INSTALL NO. 3 INTAKE MANIFOLD
30.CONNECT NO. 2 ENGINE WIRE
17113
31.INSTALL INTAKE PIPE
23763
32.INSTALL NO. 3 NOZZLE LEAKAGE PIPE (w/ DPF)
27148B
33.INSTALL CONNECTING WIRE (w/ DPF)
17136
34.INSTALL NO. 2 INTAKE MANIFOLD INSULATOR (w/ Intercooler)
17135A
35.INSTALL NO. 1 INTAKE MANIFOLD INSULATOR (w/ Intercooler)
23810A
36.INSTALL COMMON RAIL ASSEMBLY RH
23702
37.INSTALL INJECTION PIPE RH
23711
38.INSTALL NO. 1 PROTECTOR FUEL INJECTOR (w/ DPF)
23712
39.INSTALL NO. 2 PROTECTOR FUEL INJECTOR (w/ DPF)
11224
40.INSTALL CYLINDER HEAD COVER SILENCER RH (w/ DPF)
23705
41.INSTALL NO. 5 INJECTION PIPE SUB-ASSEMBLY
23243C
42.CONNECT FUEL PUMP MOTOR WIRE
23801L
43.INSTALL FUEL FILTER TO INJECTION PUMP FUEL PIPE SUB-ASSEMBLY
23820A
44.INSTALL COMMON RAIL ASSEMBLY LH
23765
45.INSTALL NO. 5 NOZZLE LEAKAGE PIPE (w/ DPF)
23701
46.INSTALL INJECTION PIPE LH
23764A
47.INSTALL NO. 4 NOZZLE LEAKAGE PIPE (w/ DPF)
11225
48.INSTALL CYLINDER HEAD COVER SILENCER LH (w/ DPF)
25706
49.INSTALL NO. 1 VACUUM TRANSMITTING PIPE SUB-ASSEMBLY (w/ DPF)
25860
50.INSTALL NO. 1 VACUUM SWITCHING VALVE ASSEMBLY (w/ DPF)
23802E
51.INSTALL NO. 2 FUEL PIPE SUB-ASSEMBLY (w/o DPF)
23706
52.CONNECT NO. 6 INJECTION PIPE SUB-ASSEMBLY
53.CONNECT ENGINE WIRE
Rear Side:
Install the glow plug wire harness with the nut and screw grommet.
w/ DPF:
Connect the 3 connectors.
w/o DPF:
Connect the connector.
Install the engine wire harness protector with the 2 bolts.
Install the 2 ground wires with the 2 bolts.
LH Side:
Install the engine wire protector with the 2 bolts.
Connect the 8 connectors.
Attach the wire harness clamp.
Install the engine wire harness bracket with the bolt.
for RHD:
Connect the wire harness with the wire harness clamp holder.
Attach the 3 wire harness clamps and connect the 2 connectors.
w/ DPF:
Connect the 7 connectors to the injection driver.
w/o DPF:
Connect the 4 connectors to the injection driver.
Install the ground wire with the bolt.
| *A | for Type A |
| *B | for Type B |
Type A or B can be distinguished by confirming the mark on the bolt.
Connect the wire harness holder to the relay block.
Connect the 4 connectors to the relay block.
Connect the wire harness with the wire harness clamp holder.
for RHD:
Connect the wire harness with the wire harness clamp holder.
for RHD:
Connect the ECM connector to the ECM.
for RHD:
Attach the wire harness tab to the relay block.
Connect the 4 connectors to the relay block.
Connect the generator positive (+) cable to the body panel with the 2 clamps.
Attach the generator positive (+) cable holder to the relay block, and install the cable to the relay block with the nut.
Connect the wire harness with the wire harness clamp holder, and attach the ground wire clamp to the relay block side.
Install the ground wire to the body panel with the bolt.
| *A | for Type A |
| *B | for Type B |
Type A or B can be distinguished by confirming the mark on the bolt.
RH Side:
w/ Winch:
Install the ground wire with the bolt.
Install the engine wire harness protector with the 3 bolts.
Connect the 7 connectors.
Install the wire harness bracket with the bolt.
Install the glow plug wire harness with the nut and screw grommet.
for RHD:
Install the wire harness holder with the bolt.
for RHD:
Connect the wire harness with the wire harness holder.
for LHD:
Connect the wire harness with the wire harness clamp holder.
for LHD:
Connect the ECM connector to the ECM.
for LHD:
Attach the wire harness tab to the relay block.
for LHD:
Connect the 4 connectors to the relay block.
16288
54.INSTALL NO. 4 WATER BY-PASS PIPE
16268M
55.INSTALL NO. 3 WATER BY-PASS PIPE (w/o Viscous Heater)
23274D
56.CONNECT FUEL HOSE
17885
57.INSTALL NO. 1 AIR CLEANER PIPE SUB-ASSEMBLY
87208
58.INSTALL HEATER WATER PIPE SUB-ASSEMBLY (w/ Viscous Heater)
17877
59.INSTALL NO. 2 INTAKE AIR CONNECTOR PIPE
Install the No. 2 intake air connector pipe to the No. 2 inlet compressor elbow.
| *1 | Hose Stopper |
| *a | No Gap |
Make sure there is no gap between the air pipe and hose stopper on the elbow side.
Install the bolt of the No. 2 intake air connector pipe.
Do not excessively pull the air pipe towards the front of the engine.
Tighten the hose clamp on the elbow side.
Align the 2 protrusions of the air pipe and elbow.
Install the air pipe so that the protrusion on the pipe side is within the range of the protrusion on the elbow side.
After tightening, a gap between the air pipe and hose stopper on the elbow side is acceptable.
Make sure the direction of the hose clamp is as shown in the illustration.
| *1 | Protrusion |
w/ Intercooler:
Connect the vacuum hose.
60.ADJUST COMPRESSOR OIL
88320
61.INSTALL COOLER COMPRESSOR ASSEMBLY
Temporarily install the cooler compressor with the 4 bolts.
Tighten the 4 bolts in the order shown in the illustration.
Attach the 3 wire harness clamps and connect the 4 connectors.
88704
62.INSTALL SUCTION HOSE SUB-ASSEMBLY
88711
63.INSTALL NO. 1 COOLER REFRIGERANT DISCHARGE HOSE
17806
64.INSTALL NO. 2 AIR CLEANER PIPE SUB-ASSEMBLY
65.INSTALL NO. 2 AIR TUBE ASSEMBLY
Apply a light coat of washer fluid to a new O-ring, and install it to the No. 2 air tube.
Install the No. 2 air tube with the bolt.
17364
66.INSTALL NO. 4 AIR TUBE
17342D
67.INSTALL NO. 2 AIR HOSE
17360E
68.INSTALL NO. 1 AIR TUBE ASSEMBLY
Apply a light coat of washer fluid to a new O-ring, and install it to the No. 1 air tube.
Install the No. 1 air tube with the bolt.
17363K
69.INSTALL NO. 3 AIR TUBE
17341F
70.INSTALL NO. 1 AIR HOSE
26100G
71.INSTALL DIESEL THROTTLE BODY ASSEMBLY LH
17947B
72.INSTALL NO. 3 INTERCOOLER SUPPORT BRACKET
23265
73.INSTALL NO. 1 GAS FILTER
31489
74.INSTALL TUBE CONNECTOR TO FLEXIBLE HOSE TUBE (for Manual Transmission)
17972
75.INSTALL AIR TUBE SUB-ASSEMBLY LH
31418
76.INSTALL CLUTCH HOSE (for Manual Transmission)
77.INSTALL DIESEL THROTTLE BODY ASSEMBLY RH
17971
78.INSTALL AIR TUBE SUB-ASSEMBLY RH
79.INSTALL NO. 2 ENGINE OIL LEVEL DIPSTICK GUIDE
87209
80.CONNECT WATER HOSE SUB-ASSEMBLY
17973
81.INSTALL NO. 2 COOL AIR INLET (w/o Intercooler)
17973
82.INSTALL NO. 1 COOL AIR INLET (w/o Intercooler)
77251B
83.CONNECT FUEL TUBE
Install new No. 1 and No. 3 fuel tube clamps.
w/ DPF:
Connect the 2 fuel tubes to the clamps.
w/o DPF:
Connect the 3 fuel tubes to the clamps.
41533
84.CONNECT FRONT DIFFERENTIAL BREATHER TUBE
16400
86.INSTALL RADIATOR ASSEMBLY
53294C
87.CONNECT RADIATOR SIDE DEFLECTOR LH
53293C
88.CONNECT RADIATOR SIDE DEFLECTOR RH (for Manual Transmission)
32917
89.INSTALL TRANSMISSION OIL COOLER AIR DUCT (for Automatic Transmission)
52119A
90.INSTALL FRONT BUMPER COVER
53111
91.INSTALL RADIATOR GRILLE
52049
92.INSTALL FRONT BUMPER WINCH COVER (w/ Winch)
16371
93.INSTALL FAN PULLEY
16711
94.INSTALL FAN SHROUD WITH FAN
32942
95.INSTALL OIL COOLER TUBE (for Automatic Transmission)
16361A
96.INSTALL V-RIBBED BELT
97.INSTALL NO. 3 IDLER PULLEY (w/ Viscous Heater)
98.INSTALL NO. 1 IDLER PULLEY (w/ Viscous Heater)
99.INSTALL V-RIBBED BELT (w/ Viscous Heater)
16572D
100.CONNECT NO. 2 RADIATOR HOSE
16571C
101.CONNECT NO. 1 RADIATOR HOSE
44310
102.INSTALL VANE PUMP ASSEMBLY
w/ DPF: (See page Steering>POWER ASSIST SYSTEMS>VANE PUMP(for 1VD-FTV with DPF)>INSTALLATION)
w/o DPF: (See page Steering>POWER ASSIST SYSTEMS>VANE PUMP (for 1VD-FTV without DPF)>INSTALLATION)
16470
103.INSTALL RADIATOR RESERVOIR ASSEMBLY
44369A
104.INSTALL NO. 1 OIL RESERVOIR BRACKET
44360
105.INSTALL VANE PUMP OIL RESERVOIR ASSEMBLY
106.INSTALL AIR CLEANER CASE
Install the air cleaner case with the 3 bolts.
Attach the wire harness clamp to the air cleaner case.
17801
107.INSTALL AIR CLEANER FILTER ELEMENT
17861
108.INSTALL INTAKE AIR CONNECTOR
17881
109.TEMPORARILY INSTALL NO. 1 AIR CLEANER HOSE
17705
110.INSTALL AIR CLEANER CAP SUB-ASSEMBLY
17940D
111.INSTALL INTERCOOLER ASSEMBLY (w/ Intercooler)
112.INSTALL SUB-BATTERY
28800
113.INSTALL MAIN BATTERY
82113
114.INSTALL NO. 3 ENGINE ROOM WIRE
115.INSTALL FRONT WHEEL
116.BLEED CLUTCH LINE
117.CHECK FOR CLUTCH FLUID LEAK
118.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
Connect the cables to the negative (-) main battery and sub-battery terminals.
119.BLEED AIR FROM FUEL SYSTEM
120.ADD ENGINE COOLANT
121.INSPECT FOR FUEL LEAK
122.INSPECT FOR OIL LEAK
123.INSPECT FOR COOLANT LEAK
124.INSPECT FOR EXHAUST GAS LEAK
125.CHARGE REFRIGERANT
126. WARM UP ENGINE
127.CHECK FOR REFRIGERANT GAS LEAK
53785B
128.INSTALL FRONT FENDER APRON SEAL REAR LH
Install the front fender apron seal rear LH with the 4 clips.
53783
129.INSTALL FRONT FENDER APRON SEAL FRONT LH
w/o KDSS:
Install the front fender apron seal front LH with the 4 clips.
w/ KDSS:
Install the front fender apron seal front LH with the 3 clips.
53784
130.INSTALL FRONT FENDER APRON SEAL REAR RH
Install the front fender apron seal rear RH with the 4 clips.
53782
131.INSTALL FRONT FENDER APRON SEAL FRONT RH
Install the front fender apron seal front RH with the 3 clips.
51440
132.INSTALL OIL PAN PROTECTOR ASSEMBLY
51442
133.INSTALL NO. 2 ENGINE UNDER COVER
Install the No. 2 engine under cover with the 2 bolts.
51405A
134.INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY
Install the No. 1 engine under cover with the 10 bolts.
53805
135.INSTALL FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH
Install the front fender splash shield RH with the clip, and then install the 3 bolts and 2 screws.
53806
136.INSTALL FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH
Install the front fender splash shield LH with the clip, and then install the 3 bolts and screw.
55781E
137.INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY
53301
138.INSTALL HOOD SUB-ASSEMBLY
Install the hood with the 4 bolts.
Install the 2 hood supports with the 2 bolts.
As much as possible avoid touching the stroke portions of the rod to prevent foreign matter from attaching to it. Be sure to hold the cylinders while servicing.
Do not wear cotton gloves or other similar materials when handling the rod. Fibers may attach to the rod and result in gas leaks.
Do not apply any load to the cylinders in the horizontal direction in order to prevent the rod from being deformed.
Install the hood support while supporting the hood by hand.
53301
139.ADJUST HOOD SUB-ASSEMBLY
140.INSPECT ENGINE OIL LEVEL
141.INSPECT ENGINE COOLANT LEVEL IN RESERVOIR
142.INSPECT ENGINE IDLE SPEED
143.INSPECT MAXIMUM ENGINE SPEED
53292A
144.INSTALL UPPER RADIATOR SUPPORT SEAL
12601E
145.INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY (w/ Intercooler)
146.PERFORM CRANK TIME COMPENSATION RESET FUNCTION