Home › Engine / Hybrid System › 3UR-FE (LUBRICATION) › OIL AND OIL FILTER › 2014.08–2019.08
RM2660E _51 Engine / Hybrid System _052796 3UR-FE LUBRICATION _0255203 OIL AND OIL FILTER A

3UR-FE LUBRICATION  OIL AND OIL FILTER  REPLACEMENT  


CAUTION / NOTICE / HINT

CAUTION:
·

Prolonged and repeated contact with engine oil will result in the removal of natural oils from the skin, leading to dryness, irritation and dermatitis. In addition, used engine oil contains potentially harmful contaminants which may cause skin cancer.

·

Precautions should be taken when replacing engine oil to minimize the risk of your skin making contact with used engine oil. Protective clothing and gloves that cannot be penetrated by oil should be worn. The skin should be washed with soap and water, or use waterless hand cleaner, to remove any used engine oil thoroughly. Do not use gasoline, thinners, or solvents.

·

In order to protect the environment, used oil and used oil filters must be disposed of at designated disposal sites.



PROCEDURE

Hide 1.DRAIN ENGINE OIL

a.

Remove the oil filler cap.


b.
A174194

Remove the 2 bolts and No. 2 engine under cover seal.


c.

Remove the oil pan drain plug and gasket, and drain the engine oil into a container.


d.

Install a new gasket and the oil pan drain plug.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)


Hide 53806 2.REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH

Hide 51405A 3.REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY LH

a.
A238243

Remove the 5 bolts and No. 1 engine under cover sub-assembly LH.


Hide 4.REMOVE OIL FILTER ELEMENT

a.
A385336E01
0.99,0.635 1.51,0.302 1.51,0.302 1.75,0.302 false 2.198,1.417 2.719,1.083 2.719,1.083 2.958,1.083 false 1.833,0.24 2.146,0.438 0.313,0.198 10 false *1 3.063,1 3.375,1.198 0.313,0.198 10 false *2

Connect a hose with an inside diameter of 15 mm (0.591 in.) to the pipe.

Text in Illustration
*1 Pipe
*2 Hose


b.
A207196

Remove the oil filter drain plug.


c.
A237032E02
2.615,2.396 2.771,1.438 2.771,1.438 2.885,1.438 true 2.073,2.01 2.333,1.052 2.333,1.052 2.49,1.052 true 2.813,2.906 2.813,3.156 false 2.667,2.844 1.542,2.844 true 1.552,2.438 1.771,2.438 1.771,2.438 2.906,2.74 true 1.531,3.229 1.75,3.229 1.75,3.229 2.844,3.042 true 2.531,0.958 2.885,1.146 0.354,0.188 10 false *1 2.906,1.323 3.323,1.531 0.417,0.208 10 false *2 1.292,2.365 1.479,2.563 0.188,0.198 10 false *3 1.271,2.771 1.49,2.969 0.219,0.198 10 false *4 1.302,3.135 1.5,3.313 0.198,0.177 10 false *5

Install the pipe to the oil filter cap.

Text in Illustration
*1 Cap
*2 Valve
*3 Pipe
*4 O-Ring
*5 Hose

NOTICE:

If the O-ring is removed with the drain plug, install the O-ring together with the pipe.


HINT:

Use a container to catch the draining oil.



d.
A207198

Check that oil is drained from the oil filter. Then disconnect the pipe and remove the O-ring as shown in the illustration.


e.
A207199E03
0.823,0.677 1.063,0.677 1.063,0.677 1.51,0.823 true 1.896,1.531 2.208,1.76 2.208,1.76 2.417,1.76 false 2.469,1.667 2.792,1.833 0.323,0.167 10 false SST 0.604,0.583 0.802,0.75 0.198,0.167 10 false *1

Using SST, remove the oil filter cap.

SST
09228-06501  

Text in Illustration
*1 Oil Filter Bracket Clip

NOTICE:

Do not remove the oil filter bracket clip.



f.
A209947E03
0.948,0.552 1.333,0.552 false 2.135,1.198 2.51,1.198 false 0.729,0.469 0.906,0.646 0.177,0.177 10 false *1 2.552,1.115 2.771,1.292 0.219,0.177 10 false *2

Remove the oil filter element and O-ring from the oil filter cap.

Text in Illustration
*1 Oil Filter Element
*2 O-Ring

NOTICE:

Be sure to remove the cap O-ring by hand, without using any tools, to prevent damage to the cap O-ring groove.



Hide 5.INSTALL OIL FILTER ELEMENT

a.

Clean the inside of the oil filter cap, its threads and its O-ring groove.


b.

Apply a small amount of engine oil to a new O-ring and install it to the oil filter cap.


c.

Set a new oil filter element to the oil filter cap.


d.

Remove any dirt or foreign matter from the installation surface of the engine.


e.

Apply a small amount of engine oil to the O-ring again and temporarily install the oil filter cap.

NOTICE:

Do not remove the oil filter bracket clip.



f.
A207200E03
0.792,0.615 1.042,0.615 1.042,0.615 1.5,0.813 true 1.969,1.479 2.344,1.479 false 0.583,0.531 0.771,0.719 0.188,0.188 10 false *1 2.396,1.396 2.75,1.594 0.354,0.198 10 false SST

Using SST, tighten the oil filter cap.

SST
09228-06501  

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)

Text in Illustration
*1 Oil Filter Bracket Clip

NOTICE:
·

When tightening the oil filter cap, do not remove the oil filter bracket clip.

·

Make sure that the oil filter is installed securely as shown in the illustration.

·

Be careful that the O-ring does not get caught between any surrounding parts.




g.
A237033E02
2.656,2.75 1.167,2.75 true 0.948,2.667 1.125,2.833 0.177,0.167 10 false *1

Apply a small amount of engine oil to a new drain plug O-ring, and install it to the oil filter cap.

Text in Illustration
*1 O-Ring

NOTICE:

Before installing the O-ring, remove any dirt or foreign matter from the installation surface of the oil filter cap.



h.

Install the oil filter drain plug.

Torque:
13 N*m (127 kgf*cm, 9 ft.*lbf)

NOTICE:

Be careful that the O-ring does not get caught between any surrounding parts.



i.

Install the No. 2 engine under cover seal with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 6.ADD ENGINE OIL

a.

Add fresh oil and install the oil filler cap.

Standard Oil Grade:
Oil Grade Oil Viscosity (SAE)
API grade SL "Energy-Conserving", SM "Energy-Conserving", SN "Resource-Conserving" or ILSAC multigrade engine oil 5W-30
10W-30
API grade SL, SM or SN multigrade engine oil 15W-40
20W-50


Standard Oil Capacity:
Item Specified Condition
Drain and refill without oil filter change 7.1 liters (7.5 US qts, 6.2 Imp. qts)
Drain and refill with oil filter change 7.5 liters (7.9 US qts, 6.6 Imp. qts)
Dry fill 9.3 liters (9.8 US qts, 8.2 Imp. qts)



Hide 7.INSPECT FOR OIL LEAK

a.

Start the engine. Make sure that there are no oil leaks from the area that was worked on.


Hide 51405A 9.INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY LH

a.

Install the No. 1 engine under cover with the 5 bolts.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)


Hide 53806 10.INSTALL FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH