Home › Engine / Hybrid System › 1VD-FTV (LUBRICATION) › OIL AND OIL FILTER › 2014.08–2015.08
RM2660E _51 Engine / Hybrid System _052799 1VD-FTV LUBRICATION _0255220 OIL AND OIL FILTER A

1VD-FTV LUBRICATION  OIL AND OIL FILTER  REPLACEMENT  


CAUTION / NOTICE / HINT

CAUTION:
·

Prolonged and repeated contact with engine oil will result in the removal of natural oils from the skin, leading to dryness, irritation and dermatitis. In addition, used engine oil contains potentially harmful contaminants which may cause skin cancer.

·

Precautions should be taken when replacing engine oil to minimize the risk of your skin making contact with used engine oil. Protective clothing and gloves that cannot be penetrated by oil should be worn. The skin should be washed with soap and water, or use waterless hand cleaner, to remove any used engine oil thoroughly. Do not use gasoline, thinners, or solvents.

·

In order to protect the environment, used oil and used oil filters must be disposed of at designated disposal sites.



PROCEDURE

Hide 1.DRAIN ENGINE OIL

a.
A177436

Remove the 2 bolts and No. 2 engine under cover seal from the No. 2 engine under cover.


b.

Remove the oil filler cap.


c.

Remove the oil pan drain plug and gasket, and then drain the engine oil into a container.


d.

Install a new gasket and the oil pan drain plug.

Torque:
38 N*m (387 kgf*cm, 28 ft.*lbf)


Hide 53805 2.REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH

Hide 51408B 3.REMOVE ENGINE UNDER COVER SUB-ASSEMBLY RH

a.
A215101

Remove the 5 bolts and engine under cover sub-assembly RH.

HINT:
A385342E01
0.49,4 0.49,3.344 0.49,3.344 1.01,3.302 false 1.531,3.063 1.313,2.51 1.313,2.51 1.625,2.51 false 2.469,4.26 2.229,4.26 2.229,4.26 1.438,3.521 false 1.677,2.438 3.052,2.656 1.375,0.219 10 false No. 1 Cooler Packing 0.302,4.073 1.208,4.469 0.906,0.396 10 false No. 1 Engine Under Cover 2.563,4.188 3.427,4.396 0.865,0.208 10 false Perforation

If the No. 1 cooler packing is not divided, remove both sides of the engine under cover assembly and cut the packing at the perforation indicated in the illustration.



Hide 4.REMOVE OIL FILTER ELEMENT

a.
A174852

Remove the oil filter drain plug.


b.
A385336E02
0.99,0.635 1.51,0.302 1.51,0.302 1.75,0.302 false 2.198,1.417 2.719,1.083 2.719,1.083 2.896,1.083 false 1.833,0.24 2.344,0.427 0.51,0.188 10 false Pipe 2.948,1 3.344,1.177 0.396,0.177 10 false Hose

Connect a hose with an inside diameter of 15 mm (0.591 in.) to the pipe.


c.

Remove the O-ring from the oil filter drain plug and install it to the drain pipe.


d.
A174853E02
2.802,3.906 2.375,3.906 false 1.427,3.438 1.677,3.438 1.677,3.438 2.542,3.677 true 1.302,3.063 1.552,3.063 1.552,3.063 2.5,3.313 true 1.115,3.833 2.354,4.021 1.24,0.188 10 false Oil Filter Drain Pipe 0.958,3.365 1.427,3.542 0.469,0.177 10 false O-Ring 0.927,2.969 1.333,3.146 0.406,0.177 10 false Valve

Install the oil filter drain pipe to the oil filter cap and drain the engine oil.


e.

Remove the oil filter drain pipe.


f.

Apply a light coat of engine oil to a new O-ring, and install it to the oil filter drain plug.


g.
A174852

Install the oil filter drain plug to the oil filter cap.

Torque:
13 N*m (127 kgf*cm, 9 ft.*lbf)


h.
A174854E03
2.073,1.083 2.771,1.083 true 2.823,1 3.125,1.167 0.302,0.167 10 false SST

Using SST, remove the oil filter cap.

SST
09228-06501  

HINT:

Use a container to catch the draining oil. After the oil filter cap is loosened approximately 4 turns and the cap ribs are vertical, engine oil drains from the gap between the oil filter cap and oil pan.



i.
A106167E27
0.833,0.375 1.104,0.375 false 2.896,1.438 2.896,1.323 2.896,1.323 2.406,1.177 true 0.073,0.26 0.635,0.635 0.563,0.375 10 false Oil Filter Element 2.615,1.469 3.094,1.677 0.479,0.208 10 false O-Ring

Remove the oil filter element and O-ring from the oil filter cap.

NOTICE:

Be sure to remove the cap O-ring by hand, without using any tools, to prevent damage to the cap O-ring groove.



Hide 5.INSTALL OIL FILTER ELEMENT

a.
A106167E28
0.833,0.375 1.104,0.375 false 2.896,1.406 2.896,1.292 2.896,1.292 2.406,1.177 true 0.094,0.26 0.656,0.792 0.563,0.531 10 false New Oil Filter Element 2.49,1.438 3.281,1.646 0.792,0.208 10 false New O-Ring

Clean the inside of the oil filter cap, its threads and its O-ring groove.


b.

Apply a small amount of engine oil to a new O-ring and install it to the oil filter cap.


c.

Set a new oil filter element in the oil filter cap.


d.

Remove any dirt or foreign matter from the installation surface of the engine.


e.

Apply a small amount of engine oil to the O-ring again and temporarily install the oil filter cap by hand.


f.
U162994E02
2.073,1.135 2.792,1.135 true 1.646,0.604 0.958,0.76 false 1.094,0.646 0.99,0.26 false 1.24,1.198 1.135,0.802 false 2.865,1.052 3.156,1.208 0.292,0.156 10 false SST 0.063,1.01 0.938,1.167 0.875,0.156 10 true No Clearance

Using SST, tighten the oil filter cap.

SST
09228-06501  

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)

NOTICE:
·

Make sure that the oil filter is installed securely as shown in the illustration.

·

Be careful that the O-ring does not get caught between any surrounding parts.




g.
A177436

Install the No. 2 engine under cover seal to the No. 2 engine under cover with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 6.ADD ENGINE OIL

a.

Add fresh oil.

Standard Engine Oil:
Item Oil Grade Oil Viscosity (SAE)
w/ DPF ACEA C2
(Using engine oil other than ACEA C2 may damage catalytic converter)
- 0W-30
- 5W-30
(0W-30 is best choice for fuel economy and good starting in cold weather)
w/o DPF G-DLD-1, API CF-4, API CF or ACEA B1
(You may also use API CE or CD)
- 5W-30
- 10W-30
- 15W-40
- 20W-50
(5W-30 is best choice for fuel economy and good starting in cold weather).


Standard Capacity:
Item Specified Condition
Drain and refill with oil filter change 9.2 liters (9.7 US qts, 8.1 Imp. qts)
Drain and refill without oil filter change 8.2 liters (8.7 US qts, 7.2 Imp. qts)
Dry fill 9.9 liters (10.5 US qts, 8.7 Imp. qts)



b.

Install the oil filler cap.


Hide 7.INSPECT FOR ENGINE OIL LEAK

a.

Warm up the engine and check for an engine oil leak.


Hide 51408B 9.INSTALL ENGINE UNDER COVER SUB-ASSEMBLY RH

a.
A215101

Install the engine under cover sub-assembly RH with the 5 bolts.

HINT:
A209602E06
1.875,0.531 2.271,0.208 false 1.865,2.646 2.26,2.438 false 1.417,1.031 2.667,1.448 true 1.365,3.292 2.635,3.552 false 0.125,2.271 0.917,2.594 0.792,0.323 10 false Cut Type: 0.115,0.188 1.156,0.458 1.042,0.271 10 false Divided Type: 2.385,0.125 3.24,0.646 0.854,0.521 10 false No. 1 Cooler Packing 2.333,2.354 3.156,2.875 0.823,0.521 10 false No. 1 Cooler Packing 2.76,1.385 3.333,1.844 0.573,0.458 10 false Contact Surface 2.75,3.49 3.323,3.948 0.573,0.458 10 false Contact Surface

Make sure there is no gap between the ends of the No. 1 cooler packing.



Hide 53805 10.INSTALL FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH