Home › Engine / Hybrid System › CRUISE CONTROL › CRUISE CONTROL SYSTEM › 2014.08–2015.08
RM2660E _51 Engine / Hybrid System _052804 CRUISE CONTROL _0255249 CRUISE CONTROL SYSTEM J

CRUISE CONTROL  CRUISE CONTROL SYSTEM  Cruise Control Switch Circuit  


DESCRIPTION

The cruise control main switch is used to operate 7 functions: SET, - (COAST), TAP-DOWN, RES (RESUME), + (ACCELERATION), TAP-UP, and CANCEL. The SET, TAP-DOWN and - (COAST) functions, and the RES (RESUME), TAP-UP and + (ACCELERATION) functions are operated with the same switch. The cruise control main switch is an automatic return type switch which turns on only while operating it in each arrow direction and turns off after releasing it. The internal contact point of the cruise control main switch is turned on with the switch operation. Then the ECM reads the resistance value that has been changed by the switch operation to control SET, - (COAST), RES (RESUME), + (ACCELERATION) and CANCEL.

WIRING DIAGRAM

E158852E04
6.531,1.573 6.885,1.74 0.354,0.167 10 false ECM 6.531,1.396 6.958,1.573 0.427,0.177 10 false A52*2 6.531,1.219 6.958,1.396 0.427,0.177 10 false A38*1 6.031,0.302 6.354,0.469 0.323,0.167 10 false 40*4 6.031,0.146 6.354,0.313 0.323,0.167 10 false 45*3 6.438,0.406 6.781,0.563 0.344,0.156 10 false CCS 4.896,2.469 5.74,2.677 0.844,0.208 10 false Spiral Cable 5.563,0.385 5.833,0.552 0.271,0.167 10 false E12 5.563,1.969 5.833,2.135 0.271,0.167 10 false E12 5.646,0.208 5.813,0.385 0.167,0.177 10 false 1 3.781,1.833 3.948,2.01 0.167,0.177 10 false 1 5.656,1.802 5.813,1.99 0.156,0.188 10 false 2 4.708,0.219 4.865,0.396 0.156,0.177 10 false 3 4.708,1.802 4.865,1.99 0.156,0.188 10 false 4 3.792,0.271 3.948,0.458 0.156,0.188 10 false 3 5.188,0.281 5.531,0.469 0.344,0.188 10 false CCS 5.188,1.875 5.531,2.063 0.344,0.188 10 false ECC 4.635,0.396 4.885,0.563 0.25,0.167 10 false z37 4.635,1.958 4.896,2.125 0.26,0.167 10 false z37 3.833,2.5 4.813,2.854 0.979,0.354 10 false Cruise Control Switch Wire 1.104,2.396 2.875,2.604 1.771,0.208 10 false Cruise Control Main Switch 3.073,1.146 3.646,1.344 0.573,0.198 10 false ON-OFF 2.188,1.156 2.656,1.333 0.469,0.177 10 false + RES 1.313,1.156 1.781,1.333 0.469,0.177 10 false - SET 0.417,1.156 1.052,1.333 0.635,0.177 10 false CANCEL 0.083,3.208 2.292,3.375 2.208,0.167 10 false *3: for 1GR-FE, 1UR-FE, 3UR-FE 0.083,2.927 1.156,3.094 1.073,0.167 10 false *2: for RHD 0.083,2.646 1.156,2.813 1.073,0.167 10 false *1: for LHD 0.083,3.49 1.115,3.656 1.031,0.167 10 false *4: for 1VD-FTV

PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (CRUISE CONTROL MAIN SWITCH)
E149007E01
1.861,0.18 2.615,0.382 0.754,0.202 10 +RES 0.104,2.473 0.815,2.674 0.711,0.202 10 CANCEL 1.495,2.978 2.479,3.180 0.984,0.202 10 -SET 2.696,1.527 3.253,1.729 0.556,0.202 10 ON-OFF

a.

Using the intelligent tester, read the Data List (See page Engine / Hybrid System>CRUISE CONTROL>CRUISE CONTROL SYSTEM>DATA LIST / ACTIVE TEST).

Cruise Control
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Main SW M-CPU Cruise control main switch (Main CPU) / ON or OFF ON: Cruise control main switch (Main CPU) on
OFF: Cruise control main switch (Main CPU) off
-
Cancel Switch CANCEL switch signal / ON or OFF ON: CANCEL switch on
OFF: CANCEL switch off
-
SET/COAST Switch -SET switch signal / ON or OFF ON: -SET switch on
OFF: -SET switch off
-
RES/ACC Switch +RES switch signal / ON or OFF ON: +RES switch on
OFF: +RES switch off
-

OK:

The intelligent tester display changes according to operation of cruise control main switch.




OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT CRUISE CONTROL MAIN SWITCH
2.INSPECT CRUISE CONTROL MAIN SWITCH
E149006E01
2.855,0.187 3.333,0.389 0.479,0.202 10 +RES 1.891,1.936 2.602,2.138 0.711,0.202 10 CANCEL 3.661,1.964 4.081,2.166 0.421,0.202 10 -SET 4.116,0.899 4.671,1.101 0.556,0.202 10 ON-OFF 2.034,2.367 4.582,2.766 2.549,0.399 10 Component without harness connected: (Cruise Control Main Switch) 3.996,0.07 5.772,0.281 1.776,0.211 10 Cruise Control Main Switch 6.403,4.28 6.525,4.455 0.122,0.174 10 1 6.409,3.185 6.519,3.371 0.110,0.186 10 3 5.697,3.706 6.258,3.877 0.562,0.171 10 ON-OFF 6.514,3.185 7.064,3.356 0.550,0.171 10 (CCS) 6.514,4.28 7.064,4.451 0.550,0.171 10 (ECC) 4.809,3.713 5.279,3.892 0.471,0.179 10 + RES 3.931,3.713 4.402,3.892 0.471,0.179 10 - SET 3.033,3.713 3.666,3.892 0.633,0.179 10 CANCEL

a.

Remove the cruise control main switch (See page Engine / Hybrid System>CRUISE CONTROL>CRUISE CONTROL MAIN SWITCH>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
1 - 3 Neutral 1MΩ or higher
Pushed to +RES 235 to 245 Ω
Pushed to -SET 620 to 640 Ω
Pushed to CANCEL 1510 to 1570 Ω
Main switch pushed off 1MΩ or higher
Main switch pushed on Below 2.5 Ω




OK

3.INSPECT CRUISE CONTROL SWITCH WIRE

NG

3.INSPECT CRUISE CONTROL SWITCH WIRE
U165806E02
0.073,2.323 2.427,2.677 2.354,0.354 10 false Front view of wire harness connector: (to Cruise Control Main Switch) 0.073,0.063 2.396,0.385 2.323,0.323 10 false Front view of wire harness connector: (to Spiral Cable) 0.323,1.427 0.573,1.573 0.25,0.146 10 false z37

a.

Remove the cruise control switch wire.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z37-3 - 3 Always Below 1 Ω
z37-4 - 1




OK

4.INSPECT SPIRAL CABLE

NG

REPLACE CRUISE CONTROL SWITCH WIRE

4.INSPECT SPIRAL CABLE
E349630E01
3.708,0.271 4,0.458 0.292,0.188 5.083,2.521 5.375,2.708 0.292,0.188 4.375,3.458 4.448,3.156 true 4.771,3.49 4.521,3.156 true 4.417,0.073 6.875,0.521 2.458,0.448 10 false Component without harness connected: (Spiral Cable) 3.74,0.271 4.073,0.479 0.333,0.208 10 false z37 5.115,2.531 5.469,2.76 0.354,0.229 10 false E12 4.219,3.49 4.677,3.708 0.458,0.219 10 false CCS 4.792,3.49 5.188,3.708 0.396,0.219 10 false ECC

a.

If there are any defects as follows, replace the spiral cable with a new one: scratches, cracks, dents or chips on the connector or the spiral cable.


b.

Check spiral cable.

i.

Set the spiral cable to the center position (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>REMOVAL).


ii.

After setting the spiral cable to the center position, rotate the spiral cable 2.5 times clockwise, and measure the resistance according to the value(s) in the table below. Then rotate the spiral cable 5 times counterclockwise, and measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z37-3 - E12-1 (CCS) Always Below 1 Ω
z37-4 - E12-2 (ECC)



iii.

After setting the spiral cable to the center position, rotate the spiral cable 2.5 times clockwise. Then while rotating the spiral cable 5 times counterclockwise, measure the resistance according to the value(s) in the table below.

NOTICE:

As the spiral cable may break, do not rotate the spiral cable more than the specified amount.


Standard Resistance:
Tester Connection Condition Specified Condition
z37-3 - E12-1 (CCS) Always Below 1 Ω
z37-4 - E12-2 (ECC)





OK

5.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE - ECM AND BODY GROUND)

NG

5.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE - ECM AND BODY GROUND)
E349631E01
3.771,1.073 4.104,1.292 0.333,0.219 3.781,1.396 4.115,1.615 0.333,0.219 0.427,1.052 0.76,1.271 0.333,0.219 6.406,2.125 6.104,1.542 true 0.938,1.458 1.292,1.25 true 5.615,2.115 5.833,1.635 true 1.469,1.188 2.323,0.906 true 0.177,0.104 2.521,0.479 2.344,0.375 10 false Front view of wire harness connector: (to Spiral Cable) 4.344,0.094 6.688,0.469 2.344,0.375 10 false Front view of wire harness connector: (to ECM) 0.156,1.646 1.021,1.854 0.865,0.208 10 false *1: for LHD 0.177,1.917 1.125,2.146 0.948,0.229 10 false *2: for RHD 0.177,2.156 2.427,2.406 2.25,0.25 10 false *3: for 1GR-FE, 1UR-FE, 3UR-FE 0.188,2.427 1.427,2.635 1.24,0.208 10 false *4: for 1VD-FTV 3.813,1.104 4.208,1.333 0.396,0.229 10 false A38 0.458,1.083 0.844,1.271 0.385,0.188 10 false E12 3.813,1.427 4.208,1.656 0.396,0.229 10 false A52 4.125,1.104 4.51,1.292 0.385,0.188 10 false *1 4.135,1.427 4.521,1.615 0.385,0.188 10 false *2 2.385,0.802 2.771,0.99 0.385,0.188 10 false ECC 0.583,1.385 0.969,1.573 0.385,0.188 10 false CCS 5.427,2.146 5.948,2.385 0.521,0.24 10 false CCS*3 6.302,2.156 6.823,2.354 0.521,0.198 10 false CCS*4

a.

Disconnect the E12 spiral cable connector.


b.

Disconnect the A38*1 or A52*2 ECM connector.

HINT:
·

*1: for LHD

·

*2: for RHD




c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 1GR-FE LHD, 1UR-FE LHD, 3UR-FE
Tester Connection Condition Specified Condition
E12-1 (CCS) - A38-45 (CCS) Always Below 1 Ω
E12-1 (CCS) - Body ground Always 10 kΩ or higher
E12-2 (ECC) - Body ground Always Below 1 Ω

for 1GR-FE RHD, 1UR-FE RHD
Tester Connection Condition Specified Condition
E12-1 (CCS) - A52-45 (CCS) Always Below 1 Ω
E12-1 (CCS) - Body ground Always 10 kΩ or higher
E12-2 (ECC) - Body ground Always Below 1 Ω

for 1VD-FTV LHD
Tester Connection Condition Specified Condition
E12-1 (CCS) - A38-40 (CCS) Always Below 1 Ω
E12-1 (CCS) - Body ground Always 10 kΩ or higher
E12-2 (ECC) - Body ground Always Below 1 Ω

for 1VD-FTV RHD
Tester Connection Condition Specified Condition
E12-1 (CCS) - A52-40 (CCS) Always Below 1 Ω
E12-1 (CCS) - Body ground Always 10 kΩ or higher
E12-2 (ECC) - Body ground Always Below 1 Ω


Result
Result Proceed to
OK
(for 1GR-FE)
A
OK
(for 1UR-FE)
B
OK
(for 3UR-FE)
C
OK
(for 1VD-FTV)
D
NG E



A

B

C

D

E

REPAIR OR REPLACE HARNESS OR CONNECTOR