Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM › from 2015.08
RM2660E _51 Engine / Hybrid System _052804 CRUISE CONTROL _0255251 DYNAMIC RADAR CRUISE CONTROL SYSTEM C

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM  C1A0A  Front Radar Sensor Region Code Mismatch  


DESCRIPTION

The driving support ECU assembly uses the millimeter wave radar sensor assembly to detect obstacles in front of the vehicle.

Based on this information, the driving support ECU assembly sends dynamic radar cruise control operation signals.

When the destination information in the millimeter wave radar sensor assembly and driving support ECU assembly do not match, DTC C1A0A is stored.

DTC No. DTC Detection Condition Trouble Area
C1A0A When the engine switch is on (IG) and the dynamic radar cruise control system is operating, the destination information in the driving support ECU assembly and millimeter wave radar sensor assembly do not match for approximately 2 seconds or more.
·

Millimeter wave radar sensor assembly

·

Driving support ECU assembly



CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the driving support ECU assembly, always replace it with a new one. If a driving support ECU assembly which was installed to another vehicle is used, the information stored in the driving support ECU assembly will not match the information from the vehicle. As a result, a DTC may be stored.

·

When the millimeter wave radar sensor assembly is replaced with a new one, adjustment of the radar sensor beam axis must be performed (See page Engine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT).

·

First check the CAN communication system by following How to Proceed with Troubleshooting. After checking that there are no malfunctions in the CAN communication system, proceed with troubleshooting (See page Engine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).



PROCEDURE

1.CHECK FOR DTCs (RADAR CRUISE2)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).



d.

Make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the system cannot detect the malfunction.

1.

Turn the engine switch on (IG).

2.

Turn the dynamic radar cruise control system on using the cruise control main switch (ON/OFF).

3.

Wait for 2 seconds or more.




e.

Enter the following menus: Powertrain / Radar Cruise2 / Trouble Codes.


f.

Check for DTCs (See page Engine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC C1A0A is output A
DTC C1A0A is not output B




A

2.REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY

B

2.REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY
a.

Replace the millimeter wave radar sensor assembly with a new one (See page Engine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>REMOVAL).


b.

Perform millimeter wave radar sensor assembly adjustment (See page Engine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT).



NEXT

3.CHECK FOR DTCs (RADAR CRUISE2)
3.CHECK FOR DTCs (RADAR CRUISE2)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).



d.

Make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the system cannot detect the malfunction.

1.

Turn the engine switch on (IG).

2.

Turn the dynamic radar cruise control system on using the cruise control main switch (ON/OFF).

3.

Wait for 2 seconds or more.




e.

Enter the following menus: Powertrain / Radar Cruise2 / Trouble Codes.


f.

Check for DTCs (See page Engine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC C1A0A is output A
DTC C1A0A is not output B




A

4.REPLACE DRIVING SUPPORT ECU ASSEMBLY

B

END (MILLIMETER WAVE RADAR SENSOR ASSEMBLY WAS DEFECTIVE)

4.REPLACE DRIVING SUPPORT ECU ASSEMBLY
a.

Replace the driving support ECU assembly (See page Engine / Hybrid System>CRUISE CONTROL>DRIVING SUPPORT ECU>REMOVAL).



NEXT

END (DRIVING SUPPORT ECU ASSEMBLY WAS DEFECTIVE)