Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM › from 2015.08
RM2660E _51 Engine / Hybrid System _052804 CRUISE CONTROL _0255251 DYNAMIC RADAR CRUISE CONTROL SYSTEM Y

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM  HOW TO PROCEED WITH TROUBLESHOOTING  


CAUTION / NOTICE / HINT

HINT:
·

Use the following procedure to troubleshoot the dynamic radar cruise control system.

·

*: Use the GTS.



PROCEDURE

1.VEHICLE BROUGHT TO WORKSHOP
Result:
Proceed to
NEXT



NEXT

2.INSPECT BATTERY VOLTAGE
2.INSPECT BATTERY VOLTAGE
a.

Measure the battery voltage.

Standard Voltage:

11 to 14 V


If the voltage is below 11 V, replace or recharge the battery before proceeding to the next step.


Result:
Proceed to
NEXT



NEXT

3.INSPECT MILLIMETER WAVE RADAR SENSOR ASSEMBLY*
3.INSPECT MILLIMETER WAVE RADAR SENSOR ASSEMBLY*


c.

Connect the GTS to the DLC3.


d.

Turn the engine switch on (IG).


e.

Turn the GTS on.


f.

Turn the cruise control main switch (ON/OFF) on.


g.

Enter the following menus: Body Electrical / Pre-Crash 2 / Utility / Front Beam Axis Misalignment Reading.


h.

Check the amount of misalignment and make a note.


i.

Enter the following menus: Body Electrical / Pre-Crash 2 / Utility / Front Beam Axis Offset Reading.


j.

Check the amount of offset and make a note.


Result:
Proceed to
NEXT



NEXT

4.CHECK CAN COMMUNICATION SYSTEM*
4.CHECK CAN COMMUNICATION SYSTEM*
a.

Using the GTS, check that the CAN communication system is functioning normally.

OK:

CAN communication system is functioning normally.


HINT:

Refer to CAN Bus Check for the CAN communication system.




Result:
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C



A

5.CHECK DTCs (SFI SYSTEM OR ECD SYSTEM)*

B

C

5.CHECK DTCs (SFI SYSTEM OR ECD SYSTEM)*

Refer to DTC Check / Clear.


a.

Check for DTCs and note any codes that are output.


b.

Clear the DTCs.


c.

Recheck for DTCs. Try to reproduce the DTCs by duplicating the conditions indicated by the DTCs.


Result:
Result Proceed to
DTC does not reoccur A
DTC reoccurs (for 1UR-FE) B
DTC reoccurs (for 3UR-FE) C
DTC reoccurs (for 1VD-FTV [w/ DPF]) D
DTC reoccurs (for 1VD-FTV [w/o DPF]) E



A

6.CHECK FOR DTCs (DYNAMIC RADAR CRUISE CONTROL SYSTEM)*

B

C

D

E

6.CHECK FOR DTCs (DYNAMIC RADAR CRUISE CONTROL SYSTEM)*

Refer to DTC Check / Clear.

Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR

a.

Check for DTCs and note any codes that are output.


b.

Clear the DTCs.


c.

Recheck for DTCs. Try to reproduce the DTCs by duplicating the conditions indicated by the DTCs.


Result:
Result Proceed to
DTC does not reoccur A
DTC reoccurs B



A

7.PROBLEM SYMPTOMS TABLE

B

7.PROBLEM SYMPTOMS TABLE

Refer to Problem Symptoms Table.

Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE

Result:
Result Proceed to
Fault is not listed in problem symptoms table A
Fault is listed in problem symptoms table B



A

8.OVERALL ANALYSIS AND TROUBLESHOOTING*

B

9.ADJUST, REPAIR OR REPLACE
8.OVERALL ANALYSIS AND TROUBLESHOOTING*

NEXT

9.ADJUST, REPAIR OR REPLACE
9.ADJUST, REPAIR OR REPLACE
NOTICE:

When replacing parts, make sure to check the replacement precautions.

Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>PRECAUTION


Result:
Proceed to
NEXT



NEXT

10.CONFIRMATION TEST
10.CONFIRMATION TEST
Result:
Proceed to
NEXT



NEXT

END