Home › Engine / Hybrid System › CRUISE CONTROL › MILLIMETER WAVE RADAR SENSOR › from 2015.08
RM2660E _51 Engine / Hybrid System _052804 CRUISE CONTROL _0255253 MILLIMETER WAVE RADAR SENSOR A

CRUISE CONTROL  MILLIMETER WAVE RADAR SENSOR  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:

If the millimeter wave radar sensor assembly has been struck or dropped, replace the millimeter wave radar sensor assembly with a new one.


HINT:
·

Use the same procedures for LHD and RHD vehicles.

·

The procedures listed below are for LHD vehicles.



PROCEDURE

Hide 88211B 1.INSTALL MILLIMETER WAVE RADAR SENSOR ASSEMBLY

NOTICE:
·

If the front bumper assembly or radiator grille has been replaced, check that the beam axis change mechanism is at the standard position (centered).

·

Only perform this procedure when the beam axis change mechanism adjustment position is not in the standard position (center).



a.

Set beam axis to the standard position.

i.
E332962E05
0.417,1.208 0.302,1.208 0.302,1.208 0.302,1.656 false 0.698,0.396 1.052,0.396 1.052,0.396 1.052,0.875 false 1.49,0.448 1.646,0.646 0.156,0.198 10 false A 0.219,1.656 0.427,1.875 0.208,0.219 10 false *b 0.531,0.302 0.74,0.521 0.208,0.219 10 false *a 2.188,0.24 2.344,0.438 0.156,0.198 10 false B

Turn the bolt so that the beam axis change mechanism is positioned as shown in the illustration.

Specified Condition:

Difference between (A) and (B): 1 mm (0.0394 in.) or less


NOTICE:

The beam axis change mechanism may be damaged if torque exceeding the specified amount (1.5 N*m{15kgf*cm.13 in.*lbf}) is applied.


Text in Illustration
*a Beam Axis Change Mechanism
*b Bolt



b.

Attach the 2 guides.


c.
B428692E07
0.844,2.51 1.083,2.76 0.24,0.25 10 true *a 2.438,2.5 2.677,2.75 0.24,0.25 10 true *a 2.156,1.688 2.396,1.938 0.24,0.25 10 true *b 1.115,1.708 1.333,1.917 0.219,0.208 10 true *b 2.844,2.417 3.083,2.656 0.24,0.24 10 true 1 0.49,2.417 0.729,2.656 0.24,0.24 10 false 2 1.979,1.365 2.219,1.604 0.24,0.24 10 false 3 1.354,1.365 1.594,1.604 0.24,0.24 10 false 4

Tighten the 2 bolts and 2 screws on the millimeter wave radar sensor assembly.

Torque:
Bolt : 2.5 N*m (25 kgf*cm, 22 in.*lbf)

HINT:

Tighten the bolts and screws in the order indicated in the illustration.


Text in Illustration
*a Bolt
*b Screw


d.

Connect the connector.


Hide 88211B 3.ADJUST MILLIMETER WAVE RADAR SENSOR ASSEMBLY

a.

When the millimeter wave radar sensor assembly is replaced, or the No. 1 millimeter wave radar sensor bracket is replaced or removed/installed, adjust the millimeter wave radar sensor assembly. (See page Engine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT)