Home › Engine / Hybrid System › CRUISE CONTROL › FORWARD RECOGNITION CAMERA SYSTEM › from 2015.08
RM2660E _51 Engine / Hybrid System _052804 CRUISE CONTROL _0255256 FORWARD RECOGNITION CAMERA SYSTEM C

CRUISE CONTROL  FORWARD RECOGNITION CAMERA SYSTEM  C1AAA  FCM Destination Information Uninitialized  


DESCRIPTION

When the forward recognition camera is replaced with a new one, the new forward recognition camera attempts to store the country specification information received from the main body ECU (multiplex network body ECU). If the forward recognition camera cannot store the country specification information, DTC C1AAA is stored.

DTC No. DTC Detection Condition Trouble Area
C1AAA 2 seconds after the engine switch is turned on (IG), the forward recognition camera cannot store the vehicle specification information.
·

Main body ECU (Multiplex network body ECU)

·

Forward recognition camera



CAUTION / NOTICE / HINT

NOTICE:
·

Recognition code registration is necessary when replacing the main body ECU (multiplex network body ECU).

·

If the main body ECU (multiplex network body ECU) is replaced, refer to Service Bulletin.

·

When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle. As a result, a DTC may be stored.

·

If the forward recognition camera has been replaced with a new one, be sure to perform forward recognition camera learning (See page Engine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT).



HINT:

This DTC is stored when the country specification information stored in the forward recognition camera and that stored in the main body ECU (multiplex network body ECU) do not match. If the forward recognition camera or main body ECU (multiplex network body ECU) has been replaced, check if a forward recognition camera or main body ECU (multiplex network body ECU) from another vehicle was used.


PROCEDURE

1.CHECK DTC OUTPUT (CAN COMMUNICATION DTC OUTPUT)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Chassis / Front Recognition Camera / Trouble Codes.



Result
Result Proceed to
DTC U0142 is not output A
DTC U0142 is output (for LHD) B
DTC U0142 is output (for RHD) C


A

2.CHECK DTC OUTPUT (FORWARD RECOGNITION CAMERA SYSTEM)

B

C

2.CHECK DTC OUTPUT (FORWARD RECOGNITION CAMERA SYSTEM)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Wait for approximately 1 minute.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / Front Recognition Camera / Trouble Codes.


f.

Make sure that the DTC detection conditions are met.

HINT:

If the following procedure is not performed, the previously output DTC cannot be detected.

1.

Turn engine switch on (IG) and wait 2 seconds or more.





Result
Result Proceed to
DTC C1AAA is output A
DTC C1AAA is not output B


A

3.REPLACE FORWARD RECOGNITION CAMERA

B

3.REPLACE FORWARD RECOGNITION CAMERA
a.

Replace the forward recognition camera (See page Engine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>REMOVAL).


b.

Adjust the forward recognition camera (See page Engine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT).



NEXT

4.CHECK DTC OUTPUT (FORWARD RECOGNITION CAMERA SYSTEM)
4.CHECK DTC OUTPUT (FORWARD RECOGNITION CAMERA SYSTEM)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Chassis / Front Recognition Camera / Trouble Codes.



f.

Make sure that the DTC detection conditions are met.

HINT:

If the following procedure is not performed, the previously output DTC cannot be detected.

1.

Turn engine switch on (IG) and wait 2 seconds or more.





Result
Result Proceed to
DTC C1AAA is output (for LHD) A
DTC C1AAA is output (for RHD) B
DTC C1AAA is not output C


A

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

B

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

C

END (FORWARD RECOGNITION CAMERA WAS DEFECTIVE)