Home › Drivetrain › AB60F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION UNIT › 2014.08–2015.08
RM2660E _52 Drivetrain _052805 AB60F AUTOMATIC TRANSMISSION / TRANSAXLE _0255263 AUTOMATIC TRANSMISSION UNIT A

AB60F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION UNIT  DISASSEMBLY  


PROCEDURE

Hide 35572 1.REMOVE TRANSMISSION CONTROL SHAFT LEVER RH

C177425

a.

Remove the nut, spring washer and control shaft lever.


Hide 84540 2.REMOVE PARK/NEUTRAL POSITION SWITCH ASSEMBLY

C177426

a.

Using a screwdriver, bend the tabs of the lock washer.


b.

Remove the nut, lock washer and bolt.


c.

Remove the park/neutral position switch.

HINT:

Make sure that the manual valve lever shaft has not been rotated prior to installing the park/neutral position switch as the detent spring may become detached from the manual valve lever shaft.



Hide 89413B 3.REMOVE SPEED SENSOR

C177427

a.

Remove the 2 bolts and 2 speed sensors.


b.

Remove the 2 O-rings from the sensors.


Hide 32921C 5.REMOVE OIL COOLER TUBE UNION (w/o ATF Warmer)

C177400

a.

Remove the 2 oil cooler tube unions.


b.

Remove the 2 O-rings from the oil cooler tube unions.


Hide 35122 6.REMOVE AUTOMATIC TRANSMISSION BREATHER TUBE

C178810

a.

Remove the 2 bolts.


b.

Remove the breather tube.


c.

Remove the O-ring from the tube.


Hide 35111 7.REMOVE AUTOMATIC TRANSMISSION HOUSING

a.
C227169E01
0.131,0.077 0.315,0.224 0.184,0.147 10 *A 0.131,2.251 0.315,2.398 0.184,0.147 10 *B

Remove the 14 bolts.

Text in Illustration
*A for 1VD-FTV
*B for 1UR-FE, 3UR-FE


b.

Remove the transmission housing.


Hide 35015G 8.REMOVE REAR TRANSFER ADAPTER

C162765

a.

Remove the 10 bolts.


b.

Remove the rear transfer adapter.

HINT:

Tap on the circumference of the extension housing with a plastic-faced hammer to remove the rear transfer adapter.



Hide 35015J 9.REMOVE TRANSMISSION CASE ADAPTER OIL SEAL

C162766E01
2.822,0.248 3.001,0.422 0.179,0.174 10 *1 1.59,1.201 2.485,0.318 2.485,0.318 2.667,0.318 false

a.

Using a screwdriver, pry out the oil seal.

Text in Illustration
*1 Protective Tape

NOTICE:

Be careful not to damage the rear transfer adapter.


HINT:

Wrap the tip of the screwdriver with tape.



Hide 35015E 10.REMOVE TRANSFER CASE ADAPTER RADIAL BALL BEARING

C162767E01
2.439,0.287 2.756,0.466 0.317,0.178 10 SST 2.413,0.413 1.79,0.919 false

a.

Using a screwdriver, remove the snap ring.


b.

Using SST and a press, press out the bearing.

SST
09950-60010  (09951-00650)
09950-70010  (09951-07150)


Hide 35104 11.SECURE AUTOMATIC TRANSMISSION CASE SUB-ASSEMBLY

C161613

a.

Install the transmission case to an overhaul attachment.


Hide 35106 12.REMOVE AUTOMATIC TRANSMISSION OIL PAN SUB-ASSEMBLY

U164922

NOTICE:

Do not turn the transmission over as this will contaminate the valve body with foreign matter from the bottom of the pan.


a.

Remove the drain plug, 12 bolts, oil pan and gasket.


b.

Remove the 4 magnets.


Hide 35106 13.INSPECT AUTOMATIC TRANSMISSION OIL PAN SUB-ASSEMBLY

Hide 35330 14.REMOVE VALVE BODY OIL STRAINER ASSEMBLY

C178807

a.

Turn over the transmission.


b.

Remove the 4 bolts and oil strainer from the valve body oil strainer assembly.


c.

Remove the O-ring from the valve body oil strainer assembly.


Hide 82125J 15.REMOVE NO. 1 TRANSMISSION WIRE AND NO. 2 TRANSMISSION WIRE

U152298

a.

Remove the 2 bolts and 2 temperature sensor clamps.


b.

Disconnect the 2 ATF temperature sensors.


c.

Disconnect the 9 connectors from the solenoid valves.


d.
C161614

Remove the 2 bolts and pull the No. 1 and No. 2 transmission wires out of the transmission case.


e.
C161615

Remove the 2 O-rings from the transmission wires.


Hide 35410 16.REMOVE TRANSMISSION VALVE BODY ASSEMBLY

a.

Remove the bolt, detent spring cover and detent spring.


b.
U152342

Remove the 19 bolts.


c.

Remove the valve body assembly.


Hide 35145C 17.REMOVE TRANSMISSION CASE GASKET

C161616

a.

Remove the 3 gaskets.


Hide 35159 18.REMOVE BRAKE DRUM GASKET

C161617

a.

Remove the 3 gaskets.


Hide 35251 19.REMOVE CHECK BALL BODY

C161618E04
1.854,0.542 1.531,0.542 false 1.854,1.125 1.438,1.125 false 1.938,0.479 2.167,0.667 0.229,0.188 10 true *1 1.896,1.052 2.083,1.219 0.188,0.167 10 false *2

Text in Illustration
*1 Check Ball Body
*2 Spring

a.

Remove the check ball body and spring.


Hide 35425A 20.REMOVE C-2 ACCUMULATOR PISTON

C161619

a.

While applying compressed air to the oil hole, remove the C-2 accumulator piston and spring.

NOTICE:

Be careful as the B-3 accumulator pistons may jump out.



b.

Remove the 2 O-rings from the piston.


Hide 35427K 21.REMOVE B-3 ACCUMULATOR PISTON

C228984

a.

While applying compressed air to the oil hole, remove the B-3 accumulator piston and spring.


b.

Remove the 2 O-rings from the piston.


Hide 35426D 22.REMOVE C-3 ACCUMULATOR PISTON

C161620

a.

While applying compressed air to the oil hole, remove the C-3 accumulator piston and spring.


b.

Remove the 2 O-rings from the piston.


Hide 35424F 23.REMOVE B-1 ACCUMULATOR VALVE

C161621

a.

Remove the B-1 accumulator valve and 2 springs.


Hide 35595 24.REMOVE PARKING LOCK PAWL BRACKET

C161622

a.

Remove the 3 bolts and bracket.


Hide 35501 25.REMOVE PARKING LOCK ROD SUB-ASSEMBLY

U152320

a.

Disconnect the parking lock rod from the manual valve lever sub-assembly.


Hide 35557 26.REMOVE PARKING LOCK PAWL

U152321

a.

Pull out the parking lock pawl shaft from the front side, and then remove the lock pawl and spring.


b.

Remove the E-ring from the shaft.


Hide 35505 27.REMOVE MANUAL VALVE LEVER SUB-ASSEMBLY

D027918

a.

Using a screwdriver and hammer, cut off the spacer and remove it from the shaft.


b.
C161626

Using a pin punch and hammer, tap out the spring pin.

HINT:

Slowly tap out the spring pin so that it does not fall into the transmission case.



c.

Pull the manual valve lever shaft out through the transmission case and remove the manual valve lever sub-assembly.


Hide 35506F 28.REMOVE MANUAL VALVE LEVER SHAFT OIL SEAL

C161628E02
1.037,0.05 1.207,0.202 0.170,0.152 10 *1 1.592,0.909 1.372,0.127 1.372,0.127 1.286,0.127 false

a.

Using a screwdriver, pry out the 2 oil seals.

Text in Illustration
*1 Protective Tape

NOTICE:

Be careful not to damage the transmission case.


HINT:

Wrap the tip of the screwdriver with protective tape before use.



Hide 29.REMOVE OIL PUMP ASSEMBLY

C161629

a.

Remove the 10 bolts.


b.
C161630E01
2.68,0.691 2.999,0.879 0.319,0.189 10 SST 2.645,0.827 2.182,0.949 false

Using SST, pull out the oil pump.

SST
09950-40011  (09951-04010, 09953-04020, 09958-04011, 09952-04010, 09954-04010, 09955-04031, 09955-04031)


c.
C161631

Remove the O-ring and 2 thrust bearing races from the oil pump.


Hide 30.REMOVE CLUTCH DRUM AND INPUT SHAFT ASSEMBLY

C161632

a.

Remove the clutch drum and input shaft assembly from the transmission case.


b.
C161633

Remove the clutch drum thrust washer and 2 thrust needle roller bearings.


Hide 35780B 32.REMOVE NO. 2 1-WAY CLUTCH ASSEMBLY

C161634

a.

Remove the No. 2 1-way clutch and clutch drum thrust washer from the clutch drum and input shaft assembly.


Hide 35601 33.SECURE CLUTCH DRUM AND INPUT SHAFT ASSEMBLY

a.
C161636E02
2.629,0.725 2.823,0.886 0.194,0.161 10 *2 0.282,1.071 0.458,1.225 0.176,0.154 10 *1 0.547,1.146 0.689,1.146 0.689,1.146 1.038,1.375 false 2.262,1.003 2.462,0.804 2.462,0.804 2.545,0.804 false

Place the oil pump onto the torque converter, and then place the clutch drum and input shaft assembly onto the oil pump.

Text in Illustration
*1 Torque Converter
*2 Oil Pump


Hide 35049 34.REMOVE REVERSE CLUTCH HUB SUB-ASSEMBLY

C161637

a.

Using a screwdriver, remove the snap ring.


b.
C161638

Remove the reverse clutch reaction sleeve and reverse clutch hub sub-assembly together with the rear clutch disc set from the clutch drum.


Hide 35677C 35.REMOVE REAR CLUTCH DISC SET

a.

for 1VD-FTV:

Remove the cushion plate, reverse clutch flange, 4 discs and 3 plates from the reverse clutch hub.


b.

for 1UR-FE, 3UR-FE

Remove the cushion plate, reverse clutch flange, 5 discs and 4 plates from the reverse clutch hub.


c.
C162148

Remove the flange from the clutch drum.


d.
C229006E01
2.588,0.699 2.748,0.865 0.159,0.166 10 *1 2.337,0.949 2.476,0.81 2.476,0.81 2.567,0.81 false

Using a screwdriver, remove the snap ring.

Text in Illustration
*1 Protective Tape

NOTICE:

Be careful not to damage the clutch drum.


HINT:

Wrap the tip of the screwdriver with tape.



Hide 35061 38.REMOVE FORWARD CLUTCH HUB SUB-ASSEMBLY

C161641

a.

Remove the thrust needle roller bearing, forward clutch hub and No. 3 clutch hub thrust washer from the clutch drum.


Hide 35064 40.REMOVE COAST CLUTCH HUB SUB-ASSEMBLY WITH NO. 4 1-WAY CLUTCH ASSEMBLY

C161642

a.

Remove the 2 thrust needle roller bearings, the coast clutch hub with the No. 4 1-way clutch assembly, and the thrust bearing race from the clutch drum.


Hide 35790H 42.REMOVE NO. 4 1-WAY CLUTCH ASSEMBLY

C161643

a.

Separate the No. 4 1-way clutch assembly from the coast clutch hub.


b.

Remove the No. 2 clutch hub thrust washer from the coast clutch hub.


Hide 35633B 43.REMOVE FORWARD MULTIPLE DISC CLUTCH DISC SET

C228985E01
1.67,0.202 1.831,0.362 0.161,0.161 10 *1 2.337,0.766 2.003,0.294 2.003,0.294 1.911,0.294 false

a.

Using a screwdriver, remove the snap ring.

Text in Illustration
*1 Protective Tape

NOTICE:

Be careful not to damage the forward clutch piston.


HINT:

Wrap the tip of the screwdriver with tape.



b.

Remove the flange, 6 discs, 6 plates and cushion plate from the input shaft.


Hide 35685 45.REMOVE COAST CLUTCH DISC SET

C228986E01
2.472,0.185 2.656,0.346 0.183,0.161 10 *1 2.392,0.271 2.272,0.271 2.272,0.271 1.629,0.839 false

a.

Using a screwdriver, remove the snap ring.

Text in Illustration
*1 Protective Tape

NOTICE:

Be careful not to damage the forward clutch piston.


HINT:

Wrap the tip of the screwdriver with tape.



b.

for 1VD-FTV:

Remove the coast clutch flange, 5 discs and 5 plates from the input shaft.


c.

for 1UR-FE, 3UR-FE

Remove the coast clutch flange, 4 discs and 4 plates from the input shaft.


Hide 35701 47.REMOVE INPUT SHAFT SUB-ASSEMBLY

C161648

a.

Remove the input shaft from the clutch drum.


Hide 35712A 48.REMOVE INPUT SHAFT OIL SEAL RING

C161649

a.

Remove the 4 oil seal rings from the input shaft.


Hide 35621V 49.REMOVE COAST CLUTCH PISTON

C161650E01
2.76,0.626 3.084,0.812 0.324,0.186 10 SST 2.137,0.648 2.715,0.708 2.715,0.708 1.633,0.943 false

a.

Place SST on the No. 1 clutch balancer and compress the forward clutch return spring with a press.

SST
09350-30020  (09350-07040)


b.

Using SST, remove the snap ring.

SST
09350-30020  (09350-07070)


c.
C161651

Remove the No. 1 clutch balancer and forward clutch return spring from the input shaft.


d.
C161652

Remove the O-ring from the No. 1 clutch balancer.


e.
C161653

Hold the input shaft by hand and apply compressed air to the input shaft to remove the coast clutch piston.


Hide 35603A 50.INSPECT FORWARD CLUTCH RETURN SPRING SUB-ASSEMBLY

Hide 35602A 51.REMOVE FORWARD CLUTCH PISTON SUB-ASSEMBLY

C161654

a.

Hold the input shaft by hand and apply compressed air to the input shaft to remove the forward clutch piston.


b.
C162744

Remove the O-ring from the input shaft.


Hide 35668 52.REMOVE NO. 3 CLUTCH BALANCER

C161656E01
2.693,0.685 3.029,0.858 0.336,0.173 10 SST 2.127,0.674 2.641,0.815 2.641,0.815 1.988,1.641 false

a.

Place SST on the No. 3 clutch balancer and compress the reverse clutch return spring with a press.

SST
09380-60010  (09381-06020, 09381-06030, 09381-06040, 09381-06050, 09381-06080)


b.

Using SST, remove the snap ring.

SST
09350-30020  (09350-07070)


c.

Remove the No. 3 clutch balancer.


d.
C161657

Remove the reverse clutch return spring and O-ring from the reverse clutch piston.


Hide 35048 54.REMOVE REVERSE CLUTCH PISTON SUB-ASSEMBLY

C161700

a.

Remove the reverse clutch piston from the clutch drum.


b.
C161702

Remove the O-ring from the reverse clutch piston.


c.
C161703

Remove the O-ring from the clutch drum.


Hide 35667A 55.REMOVE DIRECT CLUTCH DISC SET

C228987E01
1.312,0.222 1.468,0.369 0.156,0.147 10 *1 1.516,0.299 1.584,0.299 1.584,0.299 2.026,0.62 false

a.

Using a screwdriver, remove the snap rings from the clutch drum.

Text in Illustration
*1 Protective Tape

NOTICE:

Be careful not to damage the clutch drum.


HINT:

Wrap the tip of the screwdriver with tape.



b.

for 1VD-FTV:

Remove the direct clutch flange, 6 discs and 6 plates from the clutch drum.


c.

for 1UR-FE, 3UR-FE

Remove the direct clutch flange, 5 discs and 5 plates from the clutch drum.


Hide 35606A 57.REMOVE DIRECT CLUTCH PISTON SUB-ASSEMBLY

C161704E01
0.111,0.511 0.425,0.699 0.314,0.188 10 SST 1.952,1.079 0.504,0.636 0.504,0.636 1.118,0.73 false

a.

Place SST on the direct clutch piston and compress the direct clutch return spring with a press.

SST
09380-60010  (09381-06030, 09381-06040, 09381-06080)


b.

Using SST, remove the snap ring.

SST
09350-30020  (09350-07070)


c.

Place the oil pump onto the torque converter, and then place the clutch drum onto the oil pump.


d.
U164573E01
3.18,0.951 3.18,2.107 3.18,2.107 3.101,2.107 false 2.839,2.041 3.051,2.235 0.211,0.194 10 *1

Hold the direct clutch piston by hand and apply compressed air to the oil hole of the oil pump as shown in the illustration to remove the direct clutch piston together with the No. 2 clutch balancer and direct clutch return spring sub-assembly.

Text in Illustration
*1 Oil Hole


e.
C161706

Remove the No. 2 clutch balancer and direct clutch return spring sub-assembly from the direct clutch piston.


f.
C161812

Remove the 2 O-rings from the direct clutch piston.


Hide 35679C 59.REMOVE NO. 3 BRAKE SNAP RING

C228989E01
2.028,0.213 2.180,0.378 0.152,0.165 10 *1 2.008,0.316 1.94,0.316 1.94,0.316 1.665,0.433 false

a.

Using a screwdriver, remove the No. 3 brake snap ring from the transmission case.

Text in Illustration
*1 Protective Tape

NOTICE:

Be careful not to damage the transmission case.


HINT:

Wrap the tip of the screwdriver with tape.



Hide 35066 60.REMOVE NO. 3 BRAKE DISC SET

a.

Remove the 2 flanges, 4 discs and 3 plates from the transmission case.


Hide 35624J 62.REMOVE NO. 3 BRAKE PISTON HOLE SNAP RING

C161708E01
2.826,0.252 3.140,0.455 0.313,0.203 10 SST 2.804,0.315 2.381,0.172 false

a.

Using SST, remove the snap ring.

SST
09350-30020  (09350-07060)


Hide 35664 63.REMOVE NO. 3 BRAKE CYLINDER WITH NO. 3 BRAKE PISTON AND NO. 3 BRAKE PISTON RETURN SPRING SUB-ASSEMBLY

C161709

a.

Remove the No. 3 brake cylinder with the No. 3 brake piston and No. 3 brake piston return spring from the transmission case.


Hide 35624 64.REMOVE NO. 3 BRAKE PISTON

C162151E01
0.361,0.071 0.722,0.257 0.361,0.187 10 SST 0.713,0.202 1.031,0.367 false

a.

Using SST and a press, compress the No. 3 brake piston return spring and remove the snap ring and No. 3 brake piston return spring with a screwdriver.

SST
09380-60010  (09381-06020, 09381-06040, 09381-06060, 09381-06100, 09381-06110)


b.
C161712

Hold the No. 3 brake piston and apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the No. 3 brake cylinder to remove the No. 3 brake piston.


c.
C161713

Remove the 2 O-rings from the No. 3 brake piston.


Hide 35046 65.INSPECT NO. 3 BRAKE PISTON RETURN SPRING SUB-ASSEMBLY

Hide 35790 66.REMOVE 1-WAY CLUTCH ASSEMBLY WITH 1-WAY CLUTCH INNER RACE SUB-ASSEMBLY

C161710

a.

Remove the 1-way clutch assembly with 1-way clutch inner race from the transmission case.


Hide 35707C 68.REMOVE 1-WAY CLUTCH INNER RACE SUB-ASSEMBLY

C161711

a.

Separate the 1-way clutch inner race from the 1-way clutch assembly and remove the No. 1 planetary carrier thrust washer.


Hide 35720 69.REMOVE FRONT PLANETARY GEAR ASSEMBLY

C161714

a.

Remove the front planetary gear assembly and thrust needle roller bearing from the transmission case.


b.
C161715

Remove the No. 2 planetary carrier thrust washer, thrust bearing race and front planetary sun gear from the front planetary gear assembly.


Hide 35743 71.REMOVE FRONT PLANETARY RING GEAR WITH FRONT PLANETARY RING GEAR FLANGE SUB-ASSEMBLY AND CENTER PLANETARY RING GEAR

C161716

a.

Remove the front planetary ring gear together with the front planetary ring gear flange and center planetary ring gear from the transmission case.


b.

Remove the thrust needle roller bearing and thrust bearing race.


Hide 35743 72.REMOVE FRONT PLANETARY RING GEAR

C161717

a.

Using a screwdriver, remove the snap ring.


b.
C161718

Remove the front planetary ring gear from the center planetary ring gear.


Hide 35763 73.REMOVE CENTER PLANETARY RING GEAR

C161719

a.

Using a screwdriver, remove the snap ring.


b.
C161720

Remove the center planetary ring gear from the front planetary ring gear flange.


Hide 35681A 74.REMOVE NO. 1 BRAKE DISC SET

a.

Remove the flange, 4 discs and 4 plates from the transmission case.


Hide 35698 76.REMOVE NO. 1 BRAKE CYLINDER WITH NO. 1 BRAKE PISTON

C228991E01
0.587,3.02 0.785,3.184 0.198,0.164 10 *1 0.834,3.085 0.905,3.085 0.905,3.085 1.463,2.777 false

a.

Place SST on the brake piston return spring and compress the brake piston return spring.

SST
09380-60010  (09381-06010, 09381-06020, 09381-06050, 09381-06060, 09381-06090, 09381-06100, 09381-06110, 09381-06120)


b.

Using a screwdriver, remove the snap ring from the transmission case.

Text in Illustration
*1 Protective Tape

NOTICE:

Be careful not to damage the transmission case.


HINT:

Wrap the tip of the screwdriver with tape.



c.
C161723

Remove the brake piston return spring and No. 1 brake piston with No. 1 brake cylinder from the transmission case.


Hide 35621V 78.REMOVE NO. 1 BRAKE PISTON

C161724

a.

Hold the No. 1 brake piston and apply compressed air to the No. 1 brake cylinder to remove the No. 1 brake piston.

HINT:

If the piston does not pop out with compressed air, lift the piston out with needle-nose pliers.



b.
C162732

Remove the 2 O-rings from the No. 1 brake piston.


Hide 35750 79.REMOVE CENTER PLANETARY GEAR ASSEMBLY

C161727

a.

Remove the center planetary gear assembly and center planetary sun gear from the transmission case.


Hide 35682A 81.REMOVE NO. 2 BRAKE DISC SET

C228990E03
1.604,2.969 1.708,2.969 1.708,2.969 2.052,2.729 false 1.396,2.885 1.604,3.073 0.208,0.188 10 true *1

a.

Place SST on the flange and compress the No. 2 brake piston return spring.

SST
09380-60010  (09381-06010, 09381-06020, 09381-06050, 09381-06070, 09381-06090, 09381-06120)


b.

Using a screwdriver, remove the snap ring from the transmission case.

Text in Illustration
*1 Protective Tape

NOTICE:

Be careful not to damage the transmission case.


HINT:

Wrap the tip of the screwdriver with tape.



c.

Remove the No. 2 brake flange, flange, 4 discs, 3 plates and No. 2 brake piston return spring from the transmission case.


Hide 35045 83.INSPECT NO. 2 BRAKE PISTON RETURN SPRING SUB-ASSEMBLY

Hide 35699 84.REMOVE NO. 2 BRAKE CYLINDER WITH NO. 2 BRAKE PISTON

C161728

a.

Remove the No. 2 brake cylinder together with the No. 2 brake piston from the transmission case.


Hide 35622G 85.REMOVE NO. 2 BRAKE PISTON

C162149

a.

Hold the No. 2 brake piston and apply compressed air to the No. 2 brake cylinder to remove the No. 2 brake piston.

HINT:

If the piston does not pop out with compressed air, lift the piston out with needle-nose pliers.



b.
C162730

Remove the 2 O-rings from the No. 2 brake piston.


Hide 35713 86.REMOVE INTERMEDIATE SHAFT WITH NO. 3 1-WAY CLUTCH ASSEMBLY, REAR PLANETARY RING GEAR FLANGE AND REAR PLANETARY RING GEAR

C161730E03
0.51,1.354 0.51,1.01 false 0.344,1.365 0.646,1.531 0.302,0.167 10 true SST

a.

Using SST, remove the snap ring from the transmission case.

SST
09350-30020  (09350-07060)


b.
C161731

Remove the intermediate shaft with No. 3 1-way clutch assembly, rear planetary ring gear flange and rear planetary ring gear from the transmission case.


Hide 35797B 88.REMOVE 1-WAY CLUTCH INNER RACE

C161732

a.

Remove the No. 3 1-way clutch assembly and 1-way clutch inner race from the intermediate shaft.


Hide 35761 89.REMOVE REAR PLANETARY RING GEAR

C161733

a.

Remove the rear planetary ring gear with rear planetary ring gear flange, 3 thrust bearing races and thrust needle roller bearing from the intermediate shaft.


b.
C161734

Using a screwdriver, remove the snap ring.


c.

Remove the rear planetary ring gear flange from the rear planetary ring gear.


Hide 35684 91.REMOVE NO. 4 BRAKE DISC SET

a.

Remove the No. 4 brake flange, flange, 7 No. 4 brake discs and 6 plates from the transmission case.


Hide 35639B 93.REMOVE BRAKE PLATE STOPPER SPRING

C161735

NOTICE:

When removing the brake plate stopper spring, do not apply excessive force and do not deform it.


Hide 35760 94.REMOVE REAR PLANETARY GEAR ASSEMBLY

C162771

a.

Remove the rear planetary gear assembly from the transmission case.


b.
C162772

Remove the 2 thrust needle roller bearings from the rear planetary gear assembly.


c.
C161739

Remove the thrust bearing race from the transmission case.


Hide 35068 96.REMOVE 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY

C162152E01
0.206,0.522 0.557,0.737 0.350,0.215 10 SST 0.913,0.709 0.601,0.626 false

a.

Place SST on the 1st and reverse brake return spring and compress the 1st and reverse brake return spring.

SST
09380-60010  (09381-06030, 09381-06040, 09381-06080, 09381-06120, 09381-06130, 09381-05040, 09381-05050)


b.

Using SST, remove the snap ring and 1st and reverse brake return spring.

SST
09350-30020  (09350-07070)


c.
C161740

Hold the 1st and reverse brake piston and apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the transmission case to remove the 1st and reverse brake piston.

HINT:

If the piston does not pop out with compressed air, lift the piston out with needle-nose pliers.



d.
C161741

Remove the 3 O-rings from the 1st and reverse brake piston.


Hide 35068 97.INSPECT 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY