35572
1.REMOVE TRANSMISSION CONTROL SHAFT LEVER RH
Remove the nut, spring washer and control shaft lever.
84540
2.REMOVE PARK/NEUTRAL POSITION SWITCH ASSEMBLY
Using a screwdriver, bend the tabs of the lock washer.
Remove the nut, lock washer and bolt.
Remove the park/neutral position switch.
Make sure that the manual valve lever shaft has not been rotated prior to installing the park/neutral position switch as the detent spring may become detached from the manual valve lever shaft.
89413B
3.REMOVE SPEED SENSOR
Remove the 2 bolts and 2 speed sensors.
Remove the 2 O-rings from the sensors.
33490F
4.REMOVE TRANSMISSION OIL COOLER ASSEMBLY (w/ ATF Warmer)
32921C
5.REMOVE OIL COOLER TUBE UNION (w/o ATF Warmer)
Remove the 2 oil cooler tube unions.
Remove the 2 O-rings from the oil cooler tube unions.
35122
6.REMOVE AUTOMATIC TRANSMISSION BREATHER TUBE
Remove the 2 bolts.
Remove the breather tube.
Remove the O-ring from the tube.
35111
7.REMOVE AUTOMATIC TRANSMISSION HOUSING
Remove the 14 bolts.
| *A | for 1VD-FTV |
| *B | for 1UR-FE |
Remove the transmission housing.
35015G
8.REMOVE REAR TRANSFER ADAPTER
Remove the 10 bolts.
Remove the rear transfer adapter.
Tap on the circumference of the extension housing with a plastic-faced hammer to remove the rear transfer adapter.
35015J
9.REMOVE TRANSMISSION CASE ADAPTER OIL SEAL
Using a screwdriver, pry out the oil seal.
| *1 | Protective Tape |
Be careful not to damage the rear transfer adapter.
Wrap the tip of the screwdriver with tape.
35015E
10.REMOVE TRANSFER CASE ADAPTER RADIAL BALL BEARING
Using a screwdriver, remove the snap ring.
Using SST and a press, press out the bearing.
35104
11.SECURE AUTOMATIC TRANSMISSION CASE SUB-ASSEMBLY
Install the transmission case to an overhaul attachment.
35106
12.REMOVE AUTOMATIC TRANSMISSION OIL PAN SUB-ASSEMBLY
Do not turn the transmission over as this will contaminate the valve body with foreign matter from the bottom of the pan.
Remove the drain plug, 12 bolts, oil pan and gasket.
Remove the 4 magnets.
35106
13.INSPECT AUTOMATIC TRANSMISSION OIL PAN SUB-ASSEMBLY
35330
14.REMOVE VALVE BODY OIL STRAINER ASSEMBLY
Turn over the transmission.
Remove the 4 bolts and oil strainer from the valve body oil strainer assembly.
Remove the O-ring from the valve body oil strainer assembly.
82125J
15.REMOVE NO. 1 TRANSMISSION WIRE AND NO. 2 TRANSMISSION WIRE
Remove the 2 bolts and 2 temperature sensor clamps.
Disconnect the 2 ATF temperature sensors.
Disconnect the 9 connectors from the solenoid valves.
Remove the 2 bolts and pull the No. 1 and No. 2 transmission wires out of the transmission case.
Remove the 2 O-rings from the transmission wires.
35410
16.REMOVE TRANSMISSION VALVE BODY ASSEMBLY
Remove the bolt, detent spring cover and detent spring.
Remove the 19 bolts.
Remove the valve body assembly.
35145C
17.REMOVE TRANSMISSION CASE GASKET
Remove the 3 gaskets.
35159
18.REMOVE BRAKE DRUM GASKET
Remove the 3 gaskets.
35251
19.REMOVE CHECK BALL BODY
| *1 | Check Ball Body |
| *2 | Spring |
Remove the check ball body and spring.
35425A
20.REMOVE C-2 ACCUMULATOR PISTON
While applying compressed air to the oil hole, remove the C-2 accumulator piston and spring.
Be careful as the B-3 accumulator pistons may jump out.
Remove the 2 O-rings from the piston.
35427K
21.REMOVE B-3 ACCUMULATOR PISTON
While applying compressed air to the oil hole, remove the B-3 accumulator piston and spring.
Remove the 2 O-rings from the piston.
35426D
22.REMOVE C-3 ACCUMULATOR PISTON
While applying compressed air to the oil hole, remove the C-3 accumulator piston and spring.
Remove the 2 O-rings from the piston.
35424F
23.REMOVE B-1 ACCUMULATOR VALVE
Remove the B-1 accumulator valve and 2 springs.
35595
24.REMOVE PARKING LOCK PAWL BRACKET
Remove the 3 bolts and bracket.
35501
25.REMOVE PARKING LOCK ROD SUB-ASSEMBLY
Disconnect the parking lock rod from the manual valve lever sub-assembly.
35557
26.REMOVE PARKING LOCK PAWL
Pull out the parking lock pawl shaft from the front side, and then remove the lock pawl and spring.
Remove the E-ring from the shaft.
35505
27.REMOVE MANUAL VALVE LEVER SUB-ASSEMBLY
Using a screwdriver and hammer, cut off the spacer and remove it from the shaft.
Using a pin punch and hammer, tap out the spring pin.
Slowly tap out the spring pin so that it does not fall into the transmission case.
Pull the manual valve lever shaft out through the transmission case and remove the manual valve lever sub-assembly.
35506F
28.REMOVE MANUAL VALVE LEVER SHAFT OIL SEAL
Using a screwdriver, pry out the 2 oil seals.
| *1 | Protective Tape |
Be careful not to damage the transmission case.
Wrap the tip of the screwdriver with protective tape before use.
29.REMOVE OIL PUMP ASSEMBLY
Remove the 10 bolts.
Using SST, pull out the oil pump.
Remove the O-ring and 2 thrust bearing races from the oil pump.
30.REMOVE CLUTCH DRUM AND INPUT SHAFT ASSEMBLY
Remove the clutch drum and input shaft assembly from the transmission case.
Remove the clutch drum thrust washer and 2 thrust needle roller bearings.
35780B
31.INSPECT NO. 2 1-WAY CLUTCH ASSEMBLY
35780B
32.REMOVE NO. 2 1-WAY CLUTCH ASSEMBLY
Remove the No. 2 1-way clutch and clutch drum thrust washer from the clutch drum and input shaft assembly.
35601
33.SECURE CLUTCH DRUM AND INPUT SHAFT ASSEMBLY
Place the oil pump onto the torque converter, and then place the clutch drum and input shaft assembly onto the oil pump.
| *1 | Torque Converter |
| *2 | Oil Pump |
35049
34.REMOVE REVERSE CLUTCH HUB SUB-ASSEMBLY
Using a screwdriver, remove the snap ring.
Remove the reverse clutch reaction sleeve and reverse clutch hub sub-assembly together with the rear clutch disc set from the clutch drum.
35677C
35.REMOVE REAR CLUTCH DISC SET
for 1VD-FTV:
Remove the cushion plate, reverse clutch flange, 4 discs and 3 plates from the reverse clutch hub.
for 1UR-FE:
Remove the cushion plate, reverse clutch flange, 5 discs and 4 plates from the reverse clutch hub.
Remove the flange from the clutch drum.
Using a screwdriver, remove the snap ring.
| *1 | Protective Tape |
Be careful not to damage the clutch drum.
Wrap the tip of the screwdriver with tape.
35677C
36.INSPECT REAR CLUTCH DISC
35049
37.INSPECT REVERSE CLUTCH HUB SUB-ASSEMBLY
35061
38.REMOVE FORWARD CLUTCH HUB SUB-ASSEMBLY
Remove the thrust needle roller bearing, forward clutch hub and No. 3 clutch hub thrust washer from the clutch drum.
35061
39.INSPECT FORWARD CLUTCH HUB SUB-ASSEMBLY
35064
40.REMOVE COAST CLUTCH HUB SUB-ASSEMBLY WITH NO. 4 1-WAY CLUTCH ASSEMBLY
Remove the 2 thrust needle roller bearings, the coast clutch hub with the No. 4 1-way clutch assembly, and the thrust bearing race from the clutch drum.
35790H
41.INSPECT NO. 4 1-WAY CLUTCH ASSEMBLY
35790H
42.REMOVE NO. 4 1-WAY CLUTCH ASSEMBLY
Separate the No. 4 1-way clutch assembly from the coast clutch hub.
Remove the No. 2 clutch hub thrust washer from the coast clutch hub.
35633B
43.REMOVE FORWARD MULTIPLE DISC CLUTCH DISC SET
Using a screwdriver, remove the snap ring.
| *1 | Protective Tape |
Be careful not to damage the forward clutch piston.
Wrap the tip of the screwdriver with tape.
Remove the flange, 6 discs, 6 plates and cushion plate from the input shaft.
35633B
44.INSPECT FORWARD MULTIPLE DISC CLUTCH DISC
35685
45.REMOVE COAST CLUTCH DISC SET
Using a screwdriver, remove the snap ring.
| *1 | Protective Tape |
Be careful not to damage the forward clutch piston.
Wrap the tip of the screwdriver with tape.
for 1VD-FTV:
Remove the coast clutch flange, 5 discs and 5 plates from the input shaft.
for 1UR-FE:
Remove the coast clutch flange, 4 discs and 4 plates from the input shaft.
35685
46.INSPECT COAST CLUTCH DISC
35701
47.REMOVE INPUT SHAFT SUB-ASSEMBLY
Remove the input shaft from the clutch drum.
35712A
48.REMOVE INPUT SHAFT OIL SEAL RING
Remove the 4 oil seal rings from the input shaft.
35621V
49.REMOVE COAST CLUTCH PISTON
Place SST on the No. 1 clutch balancer and compress the forward clutch return spring with a press.
Using SST, remove the snap ring.
Remove the No. 1 clutch balancer and forward clutch return spring from the input shaft.
Remove the O-ring from the No. 1 clutch balancer.
Hold the input shaft by hand and apply compressed air to the input shaft to remove the coast clutch piston.
35603A
50.INSPECT FORWARD CLUTCH RETURN SPRING SUB-ASSEMBLY
35602A
51.REMOVE FORWARD CLUTCH PISTON SUB-ASSEMBLY
Hold the input shaft by hand and apply compressed air to the input shaft to remove the forward clutch piston.
Remove the O-ring from the input shaft.
35668
52.REMOVE NO. 3 CLUTCH BALANCER
Place SST on the No. 3 clutch balancer and compress the reverse clutch return spring with a press.
Using SST, remove the snap ring.
Remove the No. 3 clutch balancer.
Remove the reverse clutch return spring and O-ring from the reverse clutch piston.
35047
53.INSPECT REVERSE CLUTCH RETURN SPRING SUB-ASSEMBLY
35048
54.REMOVE REVERSE CLUTCH PISTON SUB-ASSEMBLY
Remove the reverse clutch piston from the clutch drum.
Remove the O-ring from the reverse clutch piston.
Remove the O-ring from the clutch drum.
35667A
55.REMOVE DIRECT CLUTCH DISC SET
Using a screwdriver, remove the snap rings from the clutch drum.
| *1 | Protective Tape |
Be careful not to damage the clutch drum.
Wrap the tip of the screwdriver with tape.
for 1VD-FTV:
Remove the direct clutch flange, 6 discs and 6 plates from the clutch drum.
for 1UR-FE:
Remove the direct clutch flange, 5 discs and 5 plates from the clutch drum.
35667A
56.INSPECT DIRECT CLUTCH DISC
35606A
57.REMOVE DIRECT CLUTCH PISTON SUB-ASSEMBLY
Place SST on the direct clutch piston and compress the direct clutch return spring with a press.
Using SST, remove the snap ring.
Place the oil pump onto the torque converter, and then place the clutch drum onto the oil pump.
Hold the direct clutch piston by hand and apply compressed air to the oil hole of the oil pump as shown in the illustration to remove the direct clutch piston together with the No. 2 clutch balancer and direct clutch return spring sub-assembly.
| *1 | Oil Hole |
Remove the No. 2 clutch balancer and direct clutch return spring sub-assembly from the direct clutch piston.
Remove the 2 O-rings from the direct clutch piston.
35604
58.INSPECT DIRECT CLUTCH RETURN SPRING SUB-ASSEMBLY
35679C
59.REMOVE NO. 3 BRAKE SNAP RING
Using a screwdriver, remove the No. 3 brake snap ring from the transmission case.
| *1 | Protective Tape |
Be careful not to damage the transmission case.
Wrap the tip of the screwdriver with tape.
35066
60.REMOVE NO. 3 BRAKE DISC SET
Remove the 2 flanges, 4 discs and 3 plates from the transmission case.
35066
61.INSPECT NO. 3 BRAKE DISC
35624J
62.REMOVE NO. 3 BRAKE PISTON HOLE SNAP RING
Using SST, remove the snap ring.
35664
63.REMOVE NO. 3 BRAKE CYLINDER WITH NO. 3 BRAKE PISTON AND NO. 3 BRAKE PISTON RETURN SPRING SUB-ASSEMBLY
Remove the No. 3 brake cylinder with the No. 3 brake piston and No. 3 brake piston return spring from the transmission case.
35624
64.REMOVE NO. 3 BRAKE PISTON
Using SST and a press, compress the No. 3 brake piston return spring and remove the snap ring and No. 3 brake piston return spring with a screwdriver.
Hold the No. 3 brake piston and apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the No. 3 brake cylinder to remove the No. 3 brake piston.
Remove the 2 O-rings from the No. 3 brake piston.
35046
65.INSPECT NO. 3 BRAKE PISTON RETURN SPRING SUB-ASSEMBLY
35790
66.REMOVE 1-WAY CLUTCH ASSEMBLY WITH 1-WAY CLUTCH INNER RACE SUB-ASSEMBLY
Remove the 1-way clutch assembly with 1-way clutch inner race from the transmission case.
35790
67.INSPECT 1-WAY CLUTCH ASSEMBLY
35707C
68.REMOVE 1-WAY CLUTCH INNER RACE SUB-ASSEMBLY
Separate the 1-way clutch inner race from the 1-way clutch assembly and remove the No. 1 planetary carrier thrust washer.
35720
69.REMOVE FRONT PLANETARY GEAR ASSEMBLY
Remove the front planetary gear assembly and thrust needle roller bearing from the transmission case.
Remove the No. 2 planetary carrier thrust washer, thrust bearing race and front planetary sun gear from the front planetary gear assembly.
35720
70.INSPECT FRONT PLANETARY GEAR ASSEMBLY
35743
71.REMOVE FRONT PLANETARY RING GEAR WITH FRONT PLANETARY RING GEAR FLANGE SUB-ASSEMBLY AND CENTER PLANETARY RING GEAR
Remove the front planetary ring gear together with the front planetary ring gear flange and center planetary ring gear from the transmission case.
Remove the thrust needle roller bearing and thrust bearing race.
35743
72.REMOVE FRONT PLANETARY RING GEAR
Using a screwdriver, remove the snap ring.
Remove the front planetary ring gear from the center planetary ring gear.
35763
73.REMOVE CENTER PLANETARY RING GEAR
Using a screwdriver, remove the snap ring.
Remove the center planetary ring gear from the front planetary ring gear flange.
35681A
74.REMOVE NO. 1 BRAKE DISC SET
Remove the flange, 4 discs and 4 plates from the transmission case.
35681A
75.INSPECT NO. 1 BRAKE DISC
35698
76.REMOVE NO. 1 BRAKE CYLINDER WITH NO. 1 BRAKE PISTON
Place SST on the brake piston return spring and compress the brake piston return spring.
Using a screwdriver, remove the snap ring from the transmission case.
| *1 | Protective Tape |
Be careful not to damage the transmission case.
Wrap the tip of the screwdriver with tape.
Remove the brake piston return spring and No. 1 brake piston with No. 1 brake cylinder from the transmission case.
35608J
77.INSPECT BRAKE PISTON RETURN SPRING SUB-ASSEMBLY
35621V
78.REMOVE NO. 1 BRAKE PISTON
Hold the No. 1 brake piston and apply compressed air to the No. 1 brake cylinder to remove the No. 1 brake piston.
If the piston does not pop out with compressed air, lift the piston out with needle-nose pliers.
Remove the 2 O-rings from the No. 1 brake piston.
35750
79.REMOVE CENTER PLANETARY GEAR ASSEMBLY
Remove the center planetary gear assembly and center planetary sun gear from the transmission case.
35750
80.INSPECT CENTER PLANETARY GEAR ASSEMBLY
35682A
81.REMOVE NO. 2 BRAKE DISC SET
Place SST on the flange and compress the No. 2 brake piston return spring.
Using a screwdriver, remove the snap ring from the transmission case.
| *1 | Protective Tape |
Be careful not to damage the transmission case.
Wrap the tip of the screwdriver with tape.
Remove the No. 2 brake flange, flange, 4 discs, 3 plates and No. 2 brake piston return spring from the transmission case.
35682A
82.INSPECT NO. 2 BRAKE DISC
35045
83.INSPECT NO. 2 BRAKE PISTON RETURN SPRING SUB-ASSEMBLY
35699
84.REMOVE NO. 2 BRAKE CYLINDER WITH NO. 2 BRAKE PISTON
Remove the No. 2 brake cylinder together with the No. 2 brake piston from the transmission case.
35622G
85.REMOVE NO. 2 BRAKE PISTON
Hold the No. 2 brake piston and apply compressed air to the No. 2 brake cylinder to remove the No. 2 brake piston.
If the piston does not pop out with compressed air, lift the piston out with needle-nose pliers.
Remove the 2 O-rings from the No. 2 brake piston.
35713
86.REMOVE INTERMEDIATE SHAFT WITH NO. 3 1-WAY CLUTCH ASSEMBLY, REAR PLANETARY RING GEAR FLANGE AND REAR PLANETARY RING GEAR
Using SST, remove the snap ring from the transmission case.
Remove the intermediate shaft with No. 3 1-way clutch assembly, rear planetary ring gear flange and rear planetary ring gear from the transmission case.
35770C
87.INSPECT NO. 3 1-WAY CLUTCH ASSEMBLY
35797B
88.REMOVE 1-WAY CLUTCH INNER RACE
Remove the No. 3 1-way clutch assembly and 1-way clutch inner race from the intermediate shaft.
35761
89.REMOVE REAR PLANETARY RING GEAR
Remove the rear planetary ring gear with rear planetary ring gear flange, 3 thrust bearing races and thrust needle roller bearing from the intermediate shaft.
Using a screwdriver, remove the snap ring.
Remove the rear planetary ring gear flange from the rear planetary ring gear.
35713
90.INSPECT INTERMEDIATE SHAFT
35684
91.REMOVE NO. 4 BRAKE DISC SET
Remove the No. 4 brake flange, flange, 7 No. 4 brake discs and 6 plates from the transmission case.
35684
92.INSPECT NO. 4 BRAKE DISC
35639B
93.REMOVE BRAKE PLATE STOPPER SPRING
When removing the brake plate stopper spring, do not apply excessive force and do not deform it.
35760
94.REMOVE REAR PLANETARY GEAR ASSEMBLY
Remove the rear planetary gear assembly from the transmission case.
Remove the 2 thrust needle roller bearings from the rear planetary gear assembly.
Remove the thrust bearing race from the transmission case.
35760
95.INSPECT REAR PLANETARY GEAR ASSEMBLY
35068
96.REMOVE 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY
Place SST on the 1st and reverse brake return spring and compress the 1st and reverse brake return spring.
Using SST, remove the snap ring and 1st and reverse brake return spring.
Hold the 1st and reverse brake piston and apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the transmission case to remove the 1st and reverse brake piston.
If the piston does not pop out with compressed air, lift the piston out with needle-nose pliers.
Remove the 3 O-rings from the 1st and reverse brake piston.
35068
97.INSPECT 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY