Home › Drivetrain › AB60F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM (for 1VD-FTV) › 2014.08–2015.08
RM2660E _52 Drivetrain _052805 AB60F AUTOMATIC TRANSMISSION / TRANSAXLE _0255265 AUTOMATIC TRANSMISSION SYSTEM(for 1VD-FTV) C

AB60F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM(for 1VD-FTV)  P0500  Vehicle Speed Sensor "A"  


DESCRIPTION

The speed sensor detects the wheel speed and sends the appropriate signals to the skid control ECU. The skid control ECU converts these wheel speed signals into a 4-pulse signal and outputs it to the ECM via the combination meter. The ECM determines the vehicle speed based on the frequency of these pulse signals.

A115899E06
0.43,1.047 1.579,1.425 1.149,0.378 10 from Wheel Speed Sensor 1.817,1.96 3.237,2.123 1.420,0.163 10 Skid Control ECU 3.722,1.96 5.142,2.123 1.420,0.163 10 Combination Meter 3.113,0.599 3.921,0.776 0.809,0.177 10 4-Pulse 5.039,0.599 5.848,0.776 0.809,0.177 10 4-Pulse 6.045,1.324 6.492,1.486 0.448,0.163 10 ECM

DTC Code DTC Detection Condition Trouble Area
P0500 While the vehicle is being driven, no vehicle speed sensor signal is transmitted to the ECM (2 trip detection logic).
·

Open or short in speed signal circuit

·

Wheel speed sensor

·

Combination meter

·

ECM

·

Skid control ECU



MONITOR DESCRIPTION

The ECM assumes that the vehicle is being driven when the indicated vehicle speed is more than 9 km/h (5.6 mph). If there is no speed signal from the combination meter despite these conditions being met, the ECM interprets this as a malfunction in the speed signal circuit. The ECM then illuminates the MIL and stores the DTC.

WIRING DIAGRAM

C177226E03
0.25,1.802 1.74,2 1.49,0.198 10 false from Skid Control ECU 5.25,1.802 5.604,2 0.354,0.198 10 false SPD 5.042,1.948 5.25,2.146 0.208,0.198 10 false 8 3.583,1.823 3.833,2.021 0.25,0.198 10 false +S 3.917,1.917 4.125,2.115 0.208,0.198 10 false 4 2.219,1.896 2.427,2.094 0.208,0.198 10 false 3 2.417,1.813 2.625,2.01 0.208,0.198 10 false SI 2.51,2.76 3.781,2.958 1.271,0.198 10 false Combination Meter 2.51,2.604 2.74,2.802 0.229,0.198 10 false E7 0.188,3.083 0.979,3.26 0.792,0.177 10 false *1: for LHD 0.198,3.385 0.99,3.563 0.792,0.177 10 false *2: for RHD 5.74,2.948 6.125,3.146 0.385,0.198 10 false ECM 5.76,2.615 6.208,2.813 0.448,0.198 10 false A38*1 5.75,2.771 6.198,2.969 0.448,0.198 10 false A52*2

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK OPERATION OF SPEEDOMETER
a.

Drive the vehicle and check whether the operation of the speedometer in the combination meter is normal.

HINT:
·

The vehicle speed sensor is operating normally if the speedometer reading is normal.

·

If the speedometer does not operate, check it by following the procedure described in Speedometer Malfunction (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>Speedometer Malfunction).





OK

2.READ VALUE USING INTELLIGENT TESTER (VEHICLE SPD)

NG

GO TO METER / GAUGE SYSTEM PROBLEM SYMPTOMS TABLE

2.READ VALUE USING INTELLIGENT TESTER (VEHICLE SPD)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester on.


d.

Enter the following menus: Powertrain / ECT / Data List.


e.

Drive the vehicle.


f.

According to the display on the tester, read the Data List.

ECT
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Vehicle Speed Vehicle speed/
Min.: 0 km/h (0 mph)
Max.: 255 km/h (158 mph)
Actual vehicle speed The speed is indicated on the speedometer.

OK:

Vehicle speeds displayed on intelligent tester and speedometer display are equal.




OK

NG

3.CHECK COMBINATION METER ASSEMBLY (+S VOLTAGE)
3.CHECK COMBINATION METER ASSEMBLY (+S VOLTAGE)
U164862E01
0.056,0.005 2.465,0.372 2.408,0.367 10 Front view of wire harness connector: (to Combination Meter) 1.61,1.013 1.985,1.246 0.375,0.233 10 E7 0.845,2.677 1.222,1.988 false 0.69,2.692 0.980,2.894 0.291,0.202 10 +S

a.

Disconnect the combination meter connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E7-4 (+S) - Body ground Ignition switch ON 4.5 to 5.5 V




OK

4.CHECK COMBINATION METER ASSEMBLY (SPD SIGNAL WAVEFORM)

NG

5.CHECK HARNESS AND CONNECTOR (COMBINATION METER - ECM)
4.CHECK COMBINATION METER ASSEMBLY (SPD SIGNAL WAVEFORM)
A384590E02
0.844,0.896 1.177,1.115 0.333,0.219 1.948,1.385 2.302,1.615 true 0.5,0.052 2.76,0.396 2.26,0.344 10 false Rear view of wire harness connector: (to Combination Meter) 0.927,0.917 1.188,1.094 0.26,0.177 10 false E7 2.365,1.542 2.625,1.719 0.26,0.177 10 false +S 5.302,2.094 6.125,2.313 0.823,0.219 10 false Turn Wheel 4.323,2.073 4.635,2.281 0.313,0.208 10 false 0 V 3.969,0.75 4.552,0.927 0.583,0.177 10 false 0 to 5 V

a.

Move the shift lever to N.


b.

Jack up the vehicle.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
E7-4 (+S) - Body ground
·

Ignition switch ON

·

Wheel is turned slowly


Voltage generated intermittently


HINT:

The output voltage should fluctuate up and down, similarly to the diagram, when the wheel is turned slowly.


Result
Result Proceed to
OK A
NG (w/ Multi-information Display) B
NG (w/o Multi-information Display) C



A

5.CHECK HARNESS AND CONNECTOR (COMBINATION METER - ECM)

B

C

5.CHECK HARNESS AND CONNECTOR (COMBINATION METER - ECM)
C358479E01
1.823,0.938 2.208,1.188 0.385,0.25 5.26,0.896 5.646,1.146 0.385,0.25 5.25,0.604 5.635,0.854 0.385,0.25 1.302,2.208 1.594,1.771 true 5.156,2.26 5.625,1.448 true 0.781,0.063 3.073,0.448 2.292,0.385 10 false Front view of wire harness connector: (to Combination Meter) 4.115,0.052 6.406,0.438 2.292,0.385 10 false Front view of wire harness connector: (to ECM) 1.927,0.979 2.24,1.177 0.313,0.198 10 false E7 5.323,0.938 5.635,1.135 0.313,0.198 10 false A52 5.323,0.656 5.635,0.854 0.313,0.198 10 false A38 5.708,0.656 6.021,0.854 0.313,0.198 10 false *1 5.677,0.927 5.99,1.125 0.313,0.198 10 false *2 1.198,2.229 1.51,2.427 0.313,0.198 10 false +S 5.021,2.302 5.708,2.51 0.688,0.208 10 false 8 (SPD) 3.49,2.01 4.365,2.219 0.875,0.208 10 false *1: for LHD 3.49,2.323 4.365,2.531 0.875,0.208 10 false *2: for RHD

a.

Disconnect the combination meter connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
E7-4 (+S) - A38-8 (SPD) Always Below 1 Ω
E7-4 (+S) or A38-8 (SPD) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
E7-4 (+S) - A52-8 (SPD) Always Below 1 Ω
E7-4 (+S) or A52-8 (SPD) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR HARNESS OR CONNECTOR