Home › Drivetrain › AB60F (AUTOMATIC TRANSMISSION / TRANSAXLE) › PARK / NEUTRAL POSITION SWITCH › 2014.08–2015.08
RM2660E _52 Drivetrain _052805 AB60F AUTOMATIC TRANSMISSION / TRANSAXLE _0255268 PARK / NEUTRAL POSITION SWITCH A

AB60F AUTOMATIC TRANSMISSION / TRANSAXLE  PARK / NEUTRAL POSITION SWITCH  INSTALLATION  


PROCEDURE

Hide 84540 1.INSTALL PARK/NEUTRAL POSITION SWITCH ASSEMBLY

HINT:

Make sure that the manual valve lever shaft has not been rotated prior to installing the park/neutral position switch as the detent spring may become detached from the manual valve lever shaft.


a.

Clean the bolt and the bolt hole.


b.

Apply adhesive to 2 or 3 threads on the end of the bolt.

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent



c.

Install the switch to the manual valve shaft.


d.
C175583

Temporarily install the park/neutral position switch assembly with the bolt.

HINT:

Tighten the bolt to the specified torque when adjusting the park/neutral position switch assembly.



e.
C175584

Install the lock washer and the nut.

Torque:
6.9 N*m (70 kgf*cm, 61 in.*lbf)


f.
C175585

Temporarily install the control shaft lever RH.


g.
C172409E01
1.013,0.171 1.156,0.338 0.143,0.167 10 P 1.758,0 1.900,0.164 0.141,0.164 10 N 1.512,0.293 1.654,0.456 0.142,0.163 10 R

Turn the control shaft lever RH counterclockwise until it stops, and then turn it clockwise 2 notches to set it to the N position.


h.

Remove the control shaft lever RH.


i.
U152677E02
1.979,1.552 0.698,1.229 false 1.969,0.927 1.74,0.115 1.74,0.115 1.917,0.115 true 2.906,0.479 2.865,0.531 false 2.771,0.594 2.76,0.615 false 2.885,0.427 2.813,0.542 false 2.833,0.438 2.719,0.594 false 2.771,0.448 2.677,0.583 false 2.74,0.417 2.646,0.573 false 2.708,0.396 2.604,0.552 false 2.583,0.5 2.563,0.542 false 1.969,0.052 3.146,0.281 1.177,0.229 10 false Neutral Basic Line 0.229,1.115 0.76,1.313 0.531,0.198 10 false Groove

Align the groove with the neutral basic line.


j.

Hold the switch in the position described above and tighten the bolt.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


k.
C177424

Using a screwdriver, bend the tabs of the lock washer.


l.

Install the transmission control rod bush and collar to the transmission control shaft lever RH.


m.
C175585

Install the transmission control shaft lever RH with the spring washer and nut.

Torque:
16 N*m (163 kgf*cm, 12 ft.*lbf)


n.

Connect the switch connector.


Hide 33702B 2.CONNECT FLOOR SHIFT GEAR SHIFTING ROD SUB-ASSEMBLY

C170828

a.

Connect the shifting rod to the transmission control shaft lever RH with the pin.


b.

Install a new clip.


Hide 17410 5.INSTALL FRONT EXHAUST PIPE ASSEMBLY (w/ DPF)

Hide 6.INSPECT FOR EXHAUST GAS LEAK