Home › Drivetrain › AB60F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM(for 3UR-FE) › 2014.08–2015.08
RM2660E _52 Drivetrain _052805 AB60F AUTOMATIC TRANSMISSION / TRANSAXLE _0255271 AUTOMATIC TRANSMISSION SYSTEM(for 3UR-FE) J

AB60F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM(for 3UR-FE)  L4 Position Switch Circuit  


DESCRIPTION

The four wheel drive control ECU judges whether the transfer is in L4 based on the information from the limit switch inside the transfer shift actuator assembly which is detected by the ECM. The four wheel drive control ECU inputs a signal to the combination meter assembly via CAN communication and turns on the 4LO indicator when the transfer is in L4.

WIRING DIAGRAM

C160106E25
5.198,1.323 5.427,1.49 0.229,0.167 10 false 21 5.51,1.208 5.938,1.406 0.427,0.198 10 false L4 1.854,1.333 2.083,1.5 0.229,0.167 10 false 21 1.51,1.219 1.75,1.417 0.24,0.198 10 false L4 1.854,1.99 2.083,2.156 0.229,0.167 10 false 16 1.51,1.885 1.75,2.083 0.24,0.198 10 false NP 1.771,3.563 1.917,3.729 0.146,0.167 10 false 3 1.531,3.458 1.708,3.656 0.177,0.198 10 false N 5.25,3.573 5.479,3.74 0.229,0.167 10 false 5 5.51,3.469 5.938,3.667 0.427,0.198 10 false TFN 5.688,4.167 5.99,4.333 0.302,0.167 10 false A38 5.667,4.333 6.094,4.531 0.427,0.198 10 false ECM 0.385,4.042 2.51,4.24 2.125,0.198 10 false Transfer Shift Actuator Assembly 0.385,3.854 0.813,4.052 0.427,0.198 10 false C38 0.385,2.667 2.365,2.865 1.979,0.198 10 false Four Wheel Drive Control ECU 0.385,2.479 0.813,2.677 0.427,0.198 10 false A27

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (FOUR WHEEL DRIVE CONTROL ECU - BODY GROUND)
a.
U164966E01
0.057,0.005 0.374,0.206 0.317,0.202 10 *a 1.571,0.194 1.947,0.427 0.375,0.233 10 A27 0.194,1.748 0.439,1.950 0.245,0.202 10 L4 0.322,1.734 0.521,1.264 false

Disconnect the four wheel drive control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A27-21 (L4) - Body ground Always 10 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to Four Wheel Drive control ECU)



OK

GO TO TRANSFER SYSTEM (INSPECTION)

NG

2.CHECK HARNESS AND CONNECTOR (FOUR WHEEL DRIVE CONTROL ECU - ECM)
2.CHECK HARNESS AND CONNECTOR (FOUR WHEEL DRIVE CONTROL ECU - ECM)
a.
U165066E01
1.689,0.244 2.064,0.477 0.375,0.233 10 A38 0.116,0.07 0.317,0.272 0.200,0.202 10 *a 1.084,1.65 1.611,1.851 0.527,0.202 10 21 (L4) 1.393,1.635 1.679,0.944 false

Disconnect the A38 ECM connector.


b.

Disconnect the four wheel drive control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A38-21 (L4) - Body ground Always 10 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to ECM)



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR