Home › Drivetrain › A750F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM(for 1GR-FE) › 2014.08–2015.08
RM2660E _52 Drivetrain _052806 A750F AUTOMATIC TRANSMISSION / TRANSAXLE _0255290 AUTOMATIC TRANSMISSION SYSTEM(for 1GR-FE) C

A750F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM(for 1GR-FE)  P0746  Pressure Control Solenoid "A" Performance (Shift Solenoid Valve SL1)  P0771  Shift Solenoid "E" Performance (Shift Solenoid Valve SR)  


DESCRIPTION

The ECM uses signals from the output shaft speed sensor and input speed sensor to detect the actual gear position (1st, 2nd, 3rd, 4th or 5th gear).

Then the ECM compares the actual gear with the shift schedule in the ECM memory to detect mechanical problems with the shift solenoid valves, valve body or automatic transmission (clutch, brake or gear, etc.).

DTC Code DTC Detection Condition Trouble Area
P0746 The gear required by the ECM does not match the actual gear when driving (2 trip detection logic).
·

Shift solenoid valve SL1 remains closed

·

Shift solenoid valve SR remains open or closed

·

Shift solenoid valve SLT remains open or closed

·

Valve body is blocked

·

Automatic transmission (clutch, brake or gear, etc.)


P0771 The gear required by the ECM does not match the actual gear when driving (2 trip detection logic*1, 1 trip detection logic*2).
·

Shift solenoid valve SR remains open or closed

·

Shift solenoid valve SL1 remains closed

·

Shift solenoid valve SLT remains open or closed

·

Valve body is blocked

·

Automatic transmission (clutch, brake or gear, etc.)



*1: w/ OBD

*2: w/o OBD


MONITOR DESCRIPTION

This DTC indicates a stuck ON malfunction or stuck OFF malfunction of the shift solenoid valve SR and SL1.

The ECM commands gear shifts by turning the shift solenoid valves ON/OFF. When the gear position commanded by the ECM and the actual gear position are not the same, the ECM illuminates the MIL and stores the DTC.

CAUTION / NOTICE / HINT

ACTIVE TEST


HINT:

Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


a.

Warm up the engine.


b.

Turn the engine switch off.


c.

Connect the intelligent tester to the DLC3.


d.

Turn the engine switch on (IG).


e.

Turn the intelligent tester on.


f.

Enter the following menus: Powertrain / Engine and ECT / Active Test.


g.

According to the display on the tester, perform the Active Test.

HINT:

While driving, the shift position can be forcibly changed with the intelligent tester.

Comparing the shift position commanded by the Active Test with the actual shift position enables you to confirm the problem (See page Drivetrain>A750F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM(for 1GR-FE)>FAIL-SAFE CHART).


Engine and ECT
Tester Display Test Part Control Range Diagnostic Note
Control the Shift Position Operate shift solenoid valve and set each shift position
·

Press "→" button: Shift up

·

Press "←" button: Shift down


It is possible to check the operation of the shift solenoid valves.
[Vehicle Condition]
The vehicle speed is 50 km/h (31 mph) or less.

HINT:
·

This test can be conducted when the vehicle speed is 50 km/h (31 mph) or less.

·

The 4th to 5th up-shift must be performed with the accelerator pedal released.

·

The 5th to 4th down-shift must be performed with the accelerator pedal released.

·

Do not operate the accelerator pedal for at least 2 seconds after shifting and do not shift successively.

·

The shift position commanded by the ECM is shown in the Data List display on the tester.

·

The shift solenoid valve SL1 and SR turns ON/OFF normally when the shift lever is in D.

ECM gear shift command 1st 2nd 3rd 4th 5th
Shift solenoid valve SL1 OFF OFF OFF OFF ON
Shift solenoid valve SR OFF OFF OFF OFF ON





PROCEDURE

1.CHECK DTC OUTPUT (IN ADDITION TO DTCS P0746 AND P0771)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / DTC.


e.

Read the DTCs using the tester.

Result
Result Proceed to
P0746 and/or P0771 is output A
P0746, P0771 and other DTCs are output B

HINT:

If any other codes besides P0746 and P0771 are output, perform troubleshooting for those DTCs first.




A

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (SHIFT SOLENOID VALVE SLT)

B

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (SHIFT SOLENOID VALVE SLT)
NOTICE:
·

Perform the test at the normal operating ATF temperature: 50 to 80°C (122 to 176°F).

·

Be careful to prevent SST hose from interfering with the exhaust pipe.

·

Perform the test with the A/C turned off.



HINT:

Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


a.
C159068E02
2.417,0.594 2.26,0.771 false 1.552,3.677 1.104,4.073 1.104,4.073 1.042,4.073 false 0.375,1.479 0.292,1.781 false 2.115,0.802 2.458,0.99 0.344,0.188 10 false SST 0.427,3.979 1.094,4.167 0.667,0.188 10 false Test Plug 0.135,1.823 0.479,2.01 0.344,0.188 10 false SST

Remove the test plug on the transmission case center right side and connect SST.


SST
09992-00095  (09992-00231, 09992-00271)

b.

Connect the intelligent tester to the DLC3.


c.

Start the engine and warm it up.


d.

Measure the line pressure with SST.


e.

Turn the intelligent tester on.


f.

Enter the following menus: Powertrain / Engine and ECT / Active Test.


g.

According to the display on the tester, perform the Active Test.


h.

Measure the line pressure.

Engine and ECT
Tester Display Test Part Control Range Diagnostic Note
Activate the Solenoid (SLT)* Operate shift solenoid valve SLT and raise line pressure ON or OFF
HINT:
·

OFF: Line pressure up (when Active Test "Activate the Solenoid (SLT)" is performed, ECM commands shift solenoid valve SLT to turn OFF)

·

ON: No action (normal operation)



[Vehicle Condition]
·

The vehicle is stopped.

·

The engine is idling.



HINT:

*: Activate the Solenoid (SLT) in the Active Test is performed to check the line pressure changes by connecting SST to the automatic transmission, which is used in the Hydraulic Test (See page Drivetrain>A750F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM(for 1GR-FE)>HYDRAULIC TEST) as well. Note that the pressure values in the Active Test and hydraulic test are different.


OK:

The line pressure changes as specified when performing the Active Test.




OK

3.INSPECT SHIFT SOLENOID VALVE SL1

NG

3.INSPECT SHIFT SOLENOID VALVE SL1
a.
C358284E03
2.417,1.688 2.615,1.156 false 1.01,1.688 1.208,1.177 false 0.74,1.698 0.5,1.188 false 2.167,1.688 1.958,1.188 false 0.469,0.177 2.917,0.521 2.448,0.344 10 false Component without harness connected: (Shift Solenoid Valve SL1) 2.552,2.719 2.76,2.927 0.208,0.208 10 false (+) 1.854,2.708 2.063,2.917 0.208,0.208 10 false (-) 0.417,0.927 0.625,1.135 0.208,0.208 10 false 2 1.875,0.917 2.083,1.125 0.208,0.208 10 false 2 2.615,0.906 2.823,1.115 0.208,0.208 10 false 1 1.198,0.906 1.406,1.115 0.208,0.208 10 false 1

Remove the shift solenoid valve SL1.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 5.0 to 5.6 Ω



c.

Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

OK:
Measurement Condition Specified Condition
·

Battery positive (+) with a 21 W bulb → Terminal 1

·

Battery negative (-) → Terminal 2


Valve moves and makes an operating noise




OK

4.INSPECT SHIFT SOLENOID VALVE SR

NG

4.INSPECT SHIFT SOLENOID VALVE SR
a.
A110988E08
0.052,0 1.804,0.181 1.752,0.181 10 Shift Solenoid Valve SR: 1.728,0.965 1.953,1.146 0.225,0.181 10 (-) 2.451,0.965 2.675,1.146 0.225,0.181 10 (+)

Remove the shift solenoid valve SR.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Shift solenoid valve SR connector terminal - Shift solenoid valve SR body 20°C (68°F) 11 to 15 Ω



c.

Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

OK:
Measurement Condition Specified Condition
·

Battery positive (+) → Shift solenoid valve SR connector

·

Battery negative (-) → Shift solenoid valve SR body


Valve moves and makes an operating noise




OK

5.INSPECT TRANSMISSION VALVE BODY ASSEMBLY

NG

5.INSPECT TRANSMISSION VALVE BODY ASSEMBLY
a.

Check the transmission valve body assembly (See page Drivetrain>A750F (AUTOMATIC TRANSMISSION / TRANSAXLE)>VALVE BODY ASSEMBLY>DISASSEMBLY).

OK:

There are no foreign objects on any valve.




OK

NG

REPAIR OR REPLACE TRANSMISSION VALVE BODY ASSEMBLY