The shift solenoid valve SLT controls the transmission line pressure for smooth transmission operation based on signals from the throttle position sensor and the vehicle speed sensor. The ECM adjusts the current of the SLT solenoid valve to control the hydraulic line pressure coming from the primary regulator valve. Appropriate line pressure assures smooth shifting with varying engine outputs.
| DTC Code | DTC Detection Condition | Trouble Area |
|---|---|---|
| P2714 | The ECM detects a malfunction of the SLT shift solenoid valve (ON side) according to the revolution difference of the turbine and output shaft, and also by the oil pressure (2 trip detection logic*1, 1 trip detection logic*2). | ·
Shift solenoid valve SLT remains open or closed ·
Shift solenoid valve S1, S2, SR, SL1 or SL2 remains open or closed ·
1-2 shift valve is stuck ·
Valve body is blocked ·
Torque convertor clutch ·
Automatic transmission (clutch, brake or gear, etc.) |
*1: w/ OBD
*2: w/o OBD
The ECM calculates the amount of heat absorbed by the friction material based on the difference in revolution (clutch slippage) between the turbine and output shaft. The ECM turns on the MIL and stores this DTC when the amount of heat absorption exceeds the specified value.
There are two reasons that make the revolution different.
When the shift solenoid valve SLT remains on, oil pressure goes down and clutch engagement force decreases.
When the shift solenoid valve remains on or off, the gear position commanded by the ECM and the actual gear position are not the same.
If you continue driving under these conditions, the clutch will burn out and the vehicle will no longer be drivable.
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs using the tester.
| Result | Proceed to |
|---|---|
| Only P2714 is output | A |
| P2714 and other DTCs are output | B |
If any other codes besides P2714 are output, perform troubleshooting for those DTCs first.
A
B
Perform the test at the normal operating ATF temperature: 50 to 80°C (122 to 176°F).
Be careful to prevent SST hose from interfering with the exhaust pipe.
Perform the test with the A/C turned off.
Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Remove the test plug on the transmission case center right side and connect SST.
Connect the intelligent tester to the DLC3.
Start the engine and warm it up.
Measure the line pressure with SST.
Turn the intelligent tester on.
Enter the following menus: Powertrain / Engine and ECT / Active Test.
According to the display on the tester, perform the Active Test.
Measure the line pressure.
| Tester Display | Test Part | Control Range | Diagnostic Note |
|---|---|---|---|
| Activate the Solenoid (SLT)* | Operate shift solenoid valve SLT and raise line pressure | ON or OFF
|
[Vehicle Condition]
·
The vehicle is stopped. ·
The engine is idling. |
*: Activate the Solenoid (SLT) in the Active Test is performed to check the line pressure changes by connecting SST to the automatic transmission, which is used in the Hydraulic Test (See page Drivetrain>A750F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM(for 1GR-FE)>HYDRAULIC TEST) as well. Note that the pressure values in the Active Test and hydraulic test are different.
The line pressure changes as specified when performing the Active Test.
OK
NG
This test should always be performed with at least 2 people.
Perform the test at the normal operating ATF temperature: 50 to 80°C (122 to 176°F).
Perform the test with the A/C turned off.
Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Connect the intelligent tester to the DLC3.
Warm up the engine.
Enter the following menus: Powertrain / Engine and ECT / Active Test.
According to the display on the tester, perform the Active Test.
While driving, the shift position can be forcibly changed with the intelligent tester.
| Tester Display | Test Part | Control Range | Diagnostic Note |
|---|---|---|---|
| Control the Shift Position | Operate shift solenoid valve and set each shift position | ·
Press "→" button: Shift up ·
Press "←" button: Shift down |
It is possible to check the operation of the shift solenoid valves.
[Vehicle Condition] The vehicle speed is 50 km/h (31 mph) or less. |
This test can be conducted when the vehicle speed is 50 km/h (31 mph) or less.
The 4th to 5th up-shift must be performed with the accelerator pedal released.
The 5th to 4th down-shift must be performed with the accelerator pedal released.
Do not operate the accelerator pedal for at least 2 seconds after shifting and do not shift successively.
The shift position commanded by the ECM is shown in the Data List display on the tester.
Compare the ECM gear shift command and the actual gear position.
Gear position changes in accordance with the tester command.
| System Condition | ECM Gear Shift Command | Proceed to | ||||||
|---|---|---|---|---|---|---|---|---|
| 1st | 2nd | 3rd | 4th | 5th | ||||
| Malfunction | Shift solenoid valve S1 | Stuck ON | 1st | 2nd | 2nd | 1st | N*1 | A |
| Stuck OFF | 4th | 3rd | 3rd | 4th | 5th | |||
| Shift solenoid valve S2 | Stuck ON*2 | 2nd | 2nd | 3rd | 3rd | N*1 | B | |
| Stuck OFF*3 | 1st | 1st | 4th | 4th | 5th | |||
| Shift solenoid valve SL2 | Stuck ON | 1st | 2nd | 3rd | 4th | N*1 | C | |
| Stuck OFF | 1st | 2nd | 3rd | 4th | 5th | |||
| Shift solenoid valve SR | Stuck ON*4 | 1st | 2nd | 3rd | 4th | 5th | D | |
| Stuck OFF*5 | 1st | 2nd | 3rd | 4th | 4th | |||
| Normal | 1st | 2nd | 3rd | 4th | 5th | E | ||
*1: Neutral
*2: When shift solenoid valve S2 is stuck ON, the vehicle cannot drive in reverse.
*3: When shift solenoid valve S2 is stuck OFF, the 4th to 5th up-shift will have a large shift shock. Also, the 5th to 4th down-shift will have time lag.
*4: When shift solenoid valve SR is stuck ON, the condition can be determined by checking if shift shock has increased excessively.
*5: When shift solenoid valve SR is stuck OFF, moving the shift lever from N to D will cause a large shift shock.
Gear shift can be determined by paying attention to changes in engine speed.
A
B
C
D
E
Remove the shift solenoid valve S1.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Shift solenoid valve S1 connector terminal - Shift solenoid valve S1 body | 20°C (68°F) | 11 to 15 Ω |
Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.
| Measurement Condition | Specified Condition |
|---|---|
·
Battery positive (+) → Shift solenoid valve S1 connector ·
Battery negative (-) → Shift solenoid valve S1 body |
Valve moves and makes an operating noise |
OK
NG
Check the transmission valve body assembly (See page Drivetrain>A750F (AUTOMATIC TRANSMISSION / TRANSAXLE)>VALVE BODY ASSEMBLY>DISASSEMBLY).
There are no foreign objects on any valve.
OK
NG
Check the torque converter clutch assembly (See page Drivetrain>A750F (AUTOMATIC TRANSMISSION / TRANSAXLE)>TORQUE CONVERTER CLUTCH AND DRIVE PLATE>INSPECTION).
The torque converter clutch operates normally.
OK
NG
Remove the shift solenoid valve S2.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Shift solenoid valve S2 connector terminal - Shift solenoid valve S2 body | 20°C (68°F) | 11 to 15 Ω |
Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.
| Measurement Condition | Specified Condition |
|---|---|
·
Battery positive (+) → Shift solenoid valve S2 connector ·
Battery negative (-) → Shift solenoid valve S2 body |
Valve moves and makes an operating noise |
OK
NG
Check the transmission valve body assembly (See page Drivetrain>A750F (AUTOMATIC TRANSMISSION / TRANSAXLE)>VALVE BODY ASSEMBLY>DISASSEMBLY).
There are no foreign objects on any valve.
OK
NG
Check the torque converter clutch assembly (See page Drivetrain>A750F (AUTOMATIC TRANSMISSION / TRANSAXLE)>TORQUE CONVERTER CLUTCH AND DRIVE PLATE>INSPECTION).
The torque converter clutch operates normally.
OK
NG
Remove the shift solenoid valve SL2.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 - 2 | 20°C (68°F) | 5.0 to 5.6 Ω |
Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.
| Measurement Condition | Specified Condition |
|---|---|
·
Battery positive (+) with a 21 W bulb → Terminal 1 ·
Battery negative (-) → Terminal 2 |
Valve moves and makes an operating noise |
OK
NG
Check the transmission valve body assembly (See page Drivetrain>A750F (AUTOMATIC TRANSMISSION / TRANSAXLE)>VALVE BODY ASSEMBLY>DISASSEMBLY).
There are no foreign objects on any valve.
OK
NG
Check the torque converter clutch assembly (See page Drivetrain>A750F (AUTOMATIC TRANSMISSION / TRANSAXLE)>TORQUE CONVERTER CLUTCH AND DRIVE PLATE>INSPECTION).
The torque converter clutch operates normally.
OK
NG
Remove the shift solenoid valve SL1.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 - 2 | 20°C (68°F) | 5.0 to 5.6 Ω |
Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.
| Measurement Condition | Specified Condition |
|---|---|
·
Battery positive (+) with a 21 W bulb → Terminal 1 ·
Battery negative (-) → Terminal 2 |
Valve moves and makes an operating noise |
OK
NG
Remove the shift solenoid valve SR.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Shift solenoid valve SR connector terminal - Shift solenoid valve SR body | 20°C (68°F) | 11 to 15 Ω |
Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.
| Measurement Condition | Specified Condition |
|---|---|
·
Battery positive (+) → Shift solenoid valve SR connector ·
Battery negative (-) → Shift solenoid valve SR body |
Valve moves and makes an operating noise |
OK
NG
Check the transmission valve body assembly (See page Drivetrain>A750F (AUTOMATIC TRANSMISSION / TRANSAXLE)>VALVE BODY ASSEMBLY>DISASSEMBLY).
There are no foreign objects on any valve.
OK
NG
Check the torque converter clutch assembly (See page Drivetrain>A750F (AUTOMATIC TRANSMISSION / TRANSAXLE)>TORQUE CONVERTER CLUTCH AND DRIVE PLATE>INSPECTION).
The torque converter clutch operates normally.
OK
NG
Remove the shift solenoid valve SLT.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 - 2 | 20°C (68°F) | 5.0 to 5.6 Ω |
Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.
| Measurement Condition | Specified Condition |
|---|---|
·
Battery positive (+) with a 21 W bulb → Terminal 2 ·
Battery negative (-) → Terminal 1 |
Valve moves and makes an operating noise |
OK
NG
Check the transmission valve body assembly (See page Drivetrain>A750F (AUTOMATIC TRANSMISSION / TRANSAXLE)>VALVE BODY ASSEMBLY>DISASSEMBLY).
There are no foreign objects on any valve.
OK
NG
Check the torque converter clutch assembly (See page Drivetrain>A750F (AUTOMATIC TRANSMISSION / TRANSAXLE)>TORQUE CONVERTER CLUTCH AND DRIVE PLATE>INSPECTION).
The torque converter clutch operates normally.
OK
NG