1. PRECAUTION
After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
53806
3.REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH
53805
4.REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH
51442
5.REMOVE NO. 2 ENGINE UNDER COVER
51405A
6.REMOVE NO. 1 ENGINE UNDER COVER
53783
7.REMOVE FRONT FENDER APRON TRIM PACKING B
53785B
8.REMOVE FRONT FENDER APRON TRIM PACKING D
53782
9.REMOVE FRONT FENDER APRON TRIM PACKING A
53784
10.REMOVE FRONT FENDER APRON TRIM PACKING C
11.DRAIN AUTOMATIC TRANSMISSION FLUID
37140
12.REMOVE FRONT PROPELLER SHAFT ASSEMBLY
37110
13.REMOVE PROPELLER SHAFT ASSEMBLY
14.REMOVE EXHAUST PIPE
33702B
15.DISCONNECT FLOOR SHIFT GEAR SHIFTING ROD SUB-ASSEMBLY
Remove the clip and pin, and disconnect the gear shifting rod from the transmission control shaft lever RH.
28100
16.REMOVE STARTER ASSEMBLY
32101A
17.REMOVE DRIVE PLATE AND TORQUE CONVERTER CLUTCH SETTING BOLT
Turn the crankshaft to gain access to the 6 bolts and remove each bolt while holding the crankshaft pulley setting bolt with a wrench.
18.SUPPORT AUTOMATIC TRANSMISSION ASSEMBLY
Support the transmission with a transmission jack. Lift the transmission slightly from the crossmember.
51203
19.REMOVE NO. 2 FRAME CROSSMEMBER SUB-ASSEMBLY
Remove the engine mounting hole cover.
Remove the 4 bolts of the rear engine mounting insulator.
Remove the 4 nuts, 4 bolts and frame crossmember.
12371
20.REMOVE REAR NO. 1 ENGINE MOUNTING INSULATOR
Remove the 4 bolts and rear engine mounting insulator from the transmission.
21.DISCONNECT WIRE HARNESS AND CONNECTOR
Remove the bolt and disconnect the ground cable.
Tilt the transmission downward.
Make sure the cooling fan does not contact the fan shroud.
Disconnect the park/neutral position switch connector, transmission wire connector, 2 transmission speed sensor connectors and 2 transfer control side connectors.
Detach the claw, press down the lever, and then disconnect the transmission wire connector.
Disconnect the 2 connector clamps and 6 harness clamps.
Remove the bolt and disconnect the wire harness.
17118
22.REMOVE MANIFOLD STAY
Remove the 3 bolts and stay.
17119
23.REMOVE NO. 2 MANIFOLD STAY
Remove the 3 bolts and stay.
35104V
24.DISCONNECT BREATHER PLUG HOSE
Disconnect the breather plug hose and detach the transfer breather hose.
32907A
25.DISCONNECT OIL COOLER TUBE
Remove the 2 bolts and disconnect the 2 hoses from the transmission, and separate the oil cooler tube from the engine.
35000
26.REMOVE AUTOMATIC TRANSMISSION ASSEMBLY
Remove the 9 bolts and transmission.
Do not use excess force when prying the transmission assembly.
36100
27.REMOVE TRANSFER ASSEMBLY
Detach the 2 breather hose clamps from the automatic transmission breather tube.
Disconnect the clamp of the ground cable from the transfer case lower protector.
Remove the 7 bolts and transfer case lower protector.
Remove the 8 bolts and transfer.
32000
28.REMOVE TORQUE CONVERTER CLUTCH ASSEMBLY
32000
29.INSPECT TORQUE CONVERTER CLUTCH ASSEMBLY