Home › Drivetrain › AE80F (AUTOMATIC TRANSMISSION / TRANSAXLE) › VALVE BODY ASSEMBLY › from 2015.08
RM2660E _52 Drivetrain _052807 AE80F AUTOMATIC TRANSMISSION / TRANSAXLE _0255299 VALVE BODY ASSEMBLY A

AE80F AUTOMATIC TRANSMISSION / TRANSAXLE  VALVE BODY ASSEMBLY  INSTALLATION  


PROCEDURE

Hide 35410 1.INSTALL TRANSMISSION VALVE BODY ASSEMBLY

a.
C329039E04
1.604,0.385 1.406,0.188 1.406,0.188 1.302,0.188 false 2.052,0.594 2.625,0.323 2.625,0.323 2.719,0.323 true 0.24,1.083 0.365,1.24 0.125,0.156 10 false A 0.156,2.573 0.281,2.729 0.125,0.156 10 false A 0.271,3.01 0.396,3.167 0.125,0.156 10 true A 1.01,3.188 1.135,3.344 0.125,0.156 10 false A 1.427,3.188 1.552,3.344 0.125,0.156 10 false A 1.865,3.208 1.99,3.365 0.125,0.156 10 false A 2.281,3.188 2.406,3.344 0.125,0.156 10 false A 2.948,2.792 3.073,2.948 0.125,0.156 10 true A 3.229,2.573 3.354,2.729 0.125,0.156 10 false A 3.229,2.24 3.354,2.396 0.125,0.156 10 false A 3.229,1.917 3.354,2.073 0.125,0.156 10 false A 0.135,1.583 0.26,1.74 0.125,0.156 10 false B 0.135,1.823 0.26,1.979 0.125,0.156 10 false B 0.063,2.198 0.188,2.354 0.125,0.156 10 false B 1.115,0.104 1.281,0.26 0.167,0.156 10 false *1 2.74,0.229 2.927,0.406 0.188,0.177 10 false *2

Insert the manual valve lever sub-assembly into the groove on the end of the manual valve and install the transmission valve body assembly to the automatic transmission case sub-assembly with the 14 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)

Text in Illustration
*1 Manual Valve Lever Sub-assembly
*2 Manual Valve

Bolt Length:
Item Specified Condition
Bolt A 28 mm (1.10 in.)
Bolt B 40 mm (1.57 in.)



b.

Mark the top of each bolt with paint.


c.

Retighten the 14 bolts an additional 90°.


d.

Check that the paint marks are now at a 90° angle to the top.


e.

Connect the 9 connectors to the solenoid valves.


f.

Connect the transmission revolution sensor (NT) connector.


g.

Coat a new O-ring with the ATF and install it to the ATF temperature sensor.


h.

Install the ATF temperature sensor and lock plate with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 35330 2.INSTALL VALVE BODY OIL STRAINER ASSEMBLY

a.

Coat a new O-ring with ATF and install it to the valve body oil strainer assembly.

NOTICE:

Ensure that the O-ring is not twisted or pinched.



b.

Install the valve body oil strainer assembly to the transmission valve body assembly with the 4 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 35106 3.INSTALL AUTOMATIC TRANSMISSION OIL PAN SUB-ASSEMBLY

a.
C329040E04
1.49,0.865 1.042,1.396 1.042,1.396 1.49,1.292 true 2.052,0.865 2.51,0.729 2.51,0.729 2.052,1.26 true 2.531,0.573 2.708,0.75 0.177,0.177 10 false *1 0.823,1.323 1,1.51 0.177,0.188 10 false *1

Install the 4 transmission oil cleaner magnets to the automatic transmission oil pan sub-assembly.

Text in Illustration
*1 Transmission Oil Cleaner Magnet


b.

Install a new automatic transmission oil pan gasket and the automatic transmission oil pan sub-assembly to the automatic transmission case sub-assembly with the 11 bolts.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)

NOTICE:
·
C157303E06
0.694,0.18 0.897,0.345 0.203,0.165 10 *a 1.617,0.18 1.828,0.336 0.211,0.156 10 *b 2.645,3.356 2.870,3.514 0.225,0.158 10 *2 0.653,3.707 0.866,3.898 0.213,0.191 10 *1 2.519,0.18 2.729,0.336 0.211,0.156 10 *b 2.347,2.509 2.557,2.665 0.211,0.156 10 *c 1.542,3.794 0.867,3.794 false 2.596,3.451 1.921,3.451 false


·

Make sure that there is no oil or foreign matter on the gasket seal surface and automatic transmission oil pan sub-assembly contact surface.

·

Install the gasket so that there is no slack in the gasket, and that the entire circumference of the seal surface is level.

·

Make sure that the 11 gasket drop prevention protrusions are set on the automatic transmission oil pan sub-assembly.

·

When tightening the automatic transmission oil pan sub-assembly, make sure that the gasket is not pinched between the sleeve of the gasket tightening area and the seal surface of the transmission.



Text in Illustration
*1 Sleeve
*2 Automatic Transmission Case Sub-assembly
*a Correct
*b Incorrect
*c Protrusion