Home › Drivetrain › AE80F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION ASSEMBLY › from 2015.08
RM2660E _52 Drivetrain _052807 AE80F AUTOMATIC TRANSMISSION / TRANSAXLE _0255296 AUTOMATIC TRANSMISSION ASSEMBLY A

AE80F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION ASSEMBLY  INSTALLATION  


PROCEDURE

Hide 32000 2.INSTALL TORQUE CONVERTER ASSEMBLY

a.
C342108E01
1.221,0.233 1.413,0.422 0.193,0.188 10 *a 0.602,0.485 1.158,0.371 1.158,0.371 0.516,0.726 false

Engage the splines of the input shaft and turbine runner.

Text in Illustration
*a Matchmarks


b.
C342109

Engage the splines of the stator shaft and stator while turning the torque converter assembly.

HINT:

If the stator shaft splines are difficult to engage with the stator splines, move the torque converter back approximately 10 mm and engage the splines while rotating the torque converter.



c.
C342110

Turn the torque converter assembly to engage the key of the oil pump drive gear and the slot on the torque converter assembly.


d.
U156207E01
3.138,0.292 3.292,0.485 0.154,0.193 10 A 0.601,0 0.757,0.181 0.156,0.181 10 *1 1.928,0 2.083,0.181 0.156,0.181 10 *1 0.864,2.819 1.020,3.001 0.156,0.181 10 *2 2.629,0.531 2.676,0.682 0.047,0.151 1.399,0.774 0.954,0.045 0.954,0.045 0.799,0.045 false 2.629,0.531 2.235,0.045 2.235,0.045 2.101,0.045 false 3.093,1.87 3.249,2.051 0.156,0.181 10 *2 2.909,1.535 2.995,1.959 2.995,1.959 3.092,1.959 false 1.661,1.757 1.293,2.904 1.293,2.904 1.064,2.904 false

Using a vernier caliper and straightedge, measure dimension A between the surface of the engine that contacts the transmission and the surface of the drive plate that contacts the torque converter.

Text in Illustration
*1 Engine Surface
*2 Drive Plate Surface

NOTICE:

Make sure to deduct the thickness of the straightedge.



e.
C329084E02
2.644,1.647 2.792,1.809 0.148,0.163 10 B

Using a vernier caliper and a straightedge, measure dimension B shown in the illustration and check that B is more than A measured in the first step.

Standard distance:

B = A + 1.00 mm (0.0394 in.) or more


NOTICE:
·

Make sure to deduct the thickness of the straightedge.


·

If the transmission is installed to the engine with the torque converter not sufficiently inserted, the torque converter may be damaged.




Hide 3.INSTALL WIRE HARNESS CLAMP BRACKET

C340170E01
1.824,3.379 2.174,3.581 0.350,0.202 10 *a 2.956,3.379 3.307,3.581 0.350,0.202 10 *b 4.061,3.372 4.333,3.546 0.272,0.174 10 *c 1.742,0 1.870,0.147 0.128,0.147 10 A 2.053,0.184 2.181,0.331 0.128,0.147 10 A 2.345,0.263 2.473,0.410 0.128,0.147 10 A 4.972,0.135 5.100,0.282 0.128,0.147 10 A 5.145,0.084 5.273,0.231 0.128,0.147 10 A 5.476,2.391 5.604,2.537 0.128,0.147 10 A 5.614,0 5.743,0.147 0.128,0.147 10 A 6.959,1.665 7.096,1.830 0.137,0.165 10 C 6.116,2.255 6.253,2.421 0.137,0.165 10 C 0.344,0.964 0.481,1.129 0.137,0.165 10 C 1.02,2.006 1.138,2.150 0.118,0.144 10 B

Text in Illustration
*a for Type A *b for Type B
*c for Type C - -

a.

Install the 11 bolts and 11 wire harness clamp brackets.

Torque:
Bolt A : 8.0 N*m (82 kgf*cm, 71 in.*lbf)
Bolt B : 29 N*m (296 kgf*cm, 21 ft.*lbf)
Bolt C (for Type A) : 7.5 N*m (76 kgf*cm, 66 in.*lbf)
Bolt C (for Type B) : 8.0 N*m (82 kgf*cm, 71 in.*lbf)
Bolt C (for Type C) : 13 N*m (132 kgf*cm, 10 ft.*lbf)

NOTICE:

Check whether the bolt being used is Type A or Type B or Type C, and then tighten the bolt using the appropriate torque.



Hide 35000 4.INSTALL AUTOMATIC TRANSMISSION ASSEMBLY

a.
C340176E01
3.045,0.365 3.246,0.520 0.201,0.156 10 *1 3.007,0.455 2.895,0.455 2.895,0.455 2.783,1.551 false 1.145,0.219 1.333,0.401 0.188,0.182 10 *2 1.127,0.309 0.738,0.309 0.738,0.309 0.39,2.191 false 1.627,1.258 0.738,0.309 false 1.139,2.917 1.323,3.101 0.184,0.184 10 *3 1.349,2.998 1.564,2.998 1.564,2.998 2.114,2.053 false

Apply clutch spline grease to the surface of the crankshaft that contacts the torque converter centerpiece.

Clutch spline grease:

Toyota Genuine Clutch Spline Grease or equivalent


Maximum grease amount:

Approximately 1 g (0.0353 oz.)


Text in Illustration
*1 Torque Converter Centerpiece
*2 Knock Pin
*3 Crankshaft
V100135

Clutch Spline Grease


b.

Confirm that the 2 knock pins are on the surface of the engine block that contacts the transmission.


c.
C341893E02
0.251,0.398 0.438,0.578 0.187,0.180 10 *a 1.317,0.493 0.504,0.506 0.504,0.506 1.437,0.712 false

Make sure that the mark is positioned as shown in the illustration.

Text in Illustration
*a Matchmarks


d.
C329081E04
0.688,0.354 0.813,0.5 0.125,0.146 10 false A 1.198,0 1.323,0.146 0.125,0.146 10 false A 2.375,0 2.5,0.146 0.125,0.146 10 false A 2.896,0.417 3.021,0.563 0.125,0.146 10 false A 3.083,1.26 3.208,1.406 0.125,0.146 10 false A 0.708,1.531 0.865,1.708 0.156,0.177 10 true B 0.542,1.177 0.667,1.323 0.125,0.146 10 true A 1.177,1.979 1.302,2.125 0.125,0.146 10 false B 2.385,1.969 2.51,2.115 0.125,0.146 10 false B 2.885,1.5 3.01,1.646 0.125,0.146 10 false B

Keeping the engine and automatic transmission assembly horizontal, align the knock pins with the holes on the automatic transmission assembly and install the 10 bolts shown in the illustration.

Torque:
for bolt A : 71 N*m (724 kgf*cm, 52 ft.*lbf)
for bolt B : 37 N*m (377 kgf*cm, 27 ft.*lbf)


Hide 6.CONNECT WIRE HARNESS AND CONNECTOR

a.

Connect the park/neutral position switch connector, 2 transmission wire connectors and 3 transfer control connectors.

C340128

HINT:

Push up the lever until the claw of the transmission wire connector makes a connection sound.



b.

Attach the 17 clamps and connect the wire harness.


c.
C340147

Connect the transfer breather hose sub-assembly to the automatic transmission assembly.


d.

Attach the 6 clamps 2 hose plugs and connect the transfer breather hose sub-assembly.


e.

Tilt up the automatic transmission.


Hide 12371 7.INSTALL REAR NO. 1 ENGINE MOUNTING INSULATOR

a.
C329074

Install the rear No. 1 engine mounting insulator to the transmission with the 4 bolts.

Torque:
59 N*m (602 kgf*cm, 44 ft.*lbf)


b.

Install the engine mounting heat insulator with the 2 bolts.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 51203 8.INSTALL NO. 2 FRAME CROSSMEMBER SUB-ASSEMBLY

a.
C329073

Temporarily install the No. 2 frame crossmember sub-assembly to the frame with the 4 bolts and 4 nuts.


b.
C329072

Lower the transmission assembly, and then install the rear No. 1 engine mounting insulator to the No. 2 frame crossmember sub-assembly with the 4 bolts.

Torque:
37 N*m (377 kgf*cm, 27 ft.*lbf)


c.

Tighten the No. 2 frame crossmember sub-assembly with the 4 bolts and 4 nuts.

Torque:
110 N*m (1122 kgf*cm, 81 ft.*lbf)


d.
C329071

w/ Cover:

Install the engine mounting hole cover.


Hide 9.CONNECT GROUND CABLE

a.
C340169

Connect the ground cable with the bolt.

Torque:
for Type A : 8.4 N*m (86 kgf*cm, 74 in.*lbf)
for Type B : 10 N*m (102 kgf*cm, 7 ft.*lbf)

HINT:
A418191C01
0.375,0.219 0.688,0.375 0.313,0.156 10 false *A 2.135,0.219 2.448,0.375 0.313,0.156 10 false *B
*A for Type A
*B for Type B


Type A or B can be distinguished by confirming the mark on the bolt.



Hide 32907A 10.CONNECT OIL COOLER TUBE

a.
C329080E04
0.573,1.865 0.885,2.052 0.313,0.188 10 false 1(A) 2.906,0.698 3.219,0.885 0.313,0.188 10 true 2(A) 0.052,0.865 0.448,1.042 0.396,0.177 10 true 3(B) 0.615,0.844 0.927,1.042 0.313,0.198 10 true (C)

Install the transmission oil cooler tube clamp sub-assembly with bolt (labeled C).

Torque:
14 N*m (143 kgf*cm, 10 ft.*lbf)


b.

Temporarily install the oil cooler tube with the 3 bolts and 2 oil cooler tube unions.


c.

Tighten the 3 bolts in the sequence shown in the illustration.

Torque:
for bolt A : 14 N*m (143 kgf*cm, 10 ft.*lbf)
for bolt B : 8.0 N*m (82 kgf*cm, 71 in.*lbf)


d.
C329079E01
2.21,2.544 2.394,2.707 0.184,0.163 10 *a

Tighten the 2 oil cooler tubes.

Torque:
Specified tightening torque : 34 N*m (347 kgf*cm, 25 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

(See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION)

·

When using 17 mm union nut wrench (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 29 N*m (297 kgf*cm, 21 ft.*lbf)



Text in Illustration
*a Torque Wrench Fulcrum Length


Hide 32101A 11.INSTALL DRIVE PLATE AND TORQUE CONVERTER SETTING BOLT

a.
A163778E01
0.9,1.607 1.201,1.763 0.302,0.156 10 SST 0.831,1.237 1.049,1.572 1.049,1.572 1.089,1.108 false

Using SST, hold the crankshaft.

SST
09213-70011  (09213-70020)
09330-00021  


b.
C329069

Install the 6 drive plate and torque converter setting bolts.

Torque:
53 N*m (535 kgf*cm, 39 ft.*lbf)

NOTICE:
·

First install the black-colored bolt, and then the remaining 5 silver colored bolts.

·

Turn the crankshaft to install the 6 drive plate and torque converter setting bolts.




Hide 33702B 14.CONNECT FLOOR SHIFT GEAR SHIFTING ROD SUB-ASSEMBLY

a.
C329054E01
0.745,0.213 0.887,0.372 0.142,0.159 10 P 1.312,0.213 1.454,0.372 0.142,0.159 10 R 1.733,0.213 1.875,0.372 0.142,0.159 10 N

Turn the transmission control shaft lever of the park/neutral position switch counterclockwise until it stops, and then turn it clockwise 2 notches to set it to the N position.


b.

Move the shift lever to N.


c.
C329055

Connect the floor shift gear shifting rod sub-assembly to the transmission control shaft lever with the pin and a new clip.


Hide 28100 16.INSTALL STARTER ASSEMBLY

Hide 37110 18.INSTALL PROPELLER SHAFT ASSEMBLY

Hide 37140 19.INSTALL FRONT PROPELLER SHAFT ASSEMBLY

Hide 20.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 27.INSPECT FOR EXHAUST GAS LEAK

Hide 53782 29.INSTALL FRONT FENDER APRON SEAL FRONT RH

Hide 51440 31.INSTALL OIL PAN PROTECTOR ASSEMBLY

a.
C171483

Install the oil pan protector with the 4 bolts.

Torque:
50 N*m (510 kgf*cm, 37 ft.*lbf)


Hide 51405A 33.INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

Hide 53806 34.INSTALL FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH

Hide 53805 35.INSTALL FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH

Hide 37.RESET MEMORY

a.

Perform the Reset Memory procedures (A/T initialization) (See page Drivetrain>AE80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM>INITIALIZATION).