Home › Drivetrain › AE80F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM › from 2015.08
RM2660E _52 Drivetrain _052807 AE80F AUTOMATIC TRANSMISSION / TRANSAXLE _0255308 AUTOMATIC TRANSMISSION SYSTEM C

AE80F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  P0812  Reverse Input Circuit  


DESCRIPTION

The park/neutral position switch detects the shift lever position and sends signals to the TCM.

DTC No. DTC Detection Condition
1.

Diagnosis Condition

2.

Malfunction Status

3.

Malfunction Time

4.

Other


Trouble Area
P0812
1.

Battery voltage is 9.5 V or higher, shift lever in R and DTC P0705 is not detected

2.

R terminal voltage is low

3.

5 times

4.

1-trip detection logic


·

Open or short in park/neutral position switch assembly circuit

·

Park/neutral position switch assembly

·

TCM


1.

Battery voltage is 9.5 V or higher, shift lever in D and DTC P0705 is not detected

2.

R terminal voltage is high

3.

5 times

4.

1-trip detection logic


·

Short in park/neutral position switch assembly circuit

·

Park/neutral position switch assembly

·

TCM



MONITOR DESCRIPTION

This DTC indicates a problem the park/neutral position switch assembly or the wire harness in the park/neutral position switch assembly circuit.

The park/neutral position switch assembly detects the shift lever position and sends signals to the TCM.

For safety, the park/neutral position switch assembly detects the shift lever position so that the engine can be started only when the shift lever is in P or N.

The park/neutral position switch assembly sends signals to the TCM according to the shift lever position (P, N, R or D).

The TCM determines that there is a problem with the switch or related parts if it receives an R position signal when the shift lever is in D or it does not receives an R position signal when the shift lever is in R. The TCM stores the DTC.

CAUTION / NOTICE / HINT

NOTICE:
·

Perform registration and/or initialization when parts related to the automatic transmission are replaced (See page Drivetrain>AE80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM>INITIALIZATION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



HINT:

After performing repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

Turn the engine switch on (IG).

2.

Wait for 5 seconds or more with the shift lever in D.

3.

Wait for 5 seconds or more with the shift lever in R.



PROCEDURE

1.CHECK PARK/NEUTRAL POSITION SWITCH ASSEMBLY (POWER SOURCE)
a.
U165583E02
1.625,0.99 1.292,0.323 true 0.396,1.042 0.823,1.24 0.427,0.198 10 false C24 0.125,0.031 0.552,0.229 0.427,0.198 10 false *a 1.063,0.198 1.49,0.396 0.427,0.198 10 false RB

Disconnect the park/neutral position switch assembly connector.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C24-1 (RB) - Body ground Engine switch on (IG) 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Park/Neutral Position Switch Assembly)



OK

2.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - BATTERY)

2.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
a.
C197712E99
1.042,0.521 1.406,0.958 false 2.188,0.5 1.833,0.948 false 1.292,0.49 1.604,0.969 false 1.958,1.281 2.323,1.719 false 0.063,0.031 0.281,0.229 0.219,0.198 10 false *a 2.229,0.333 2.521,0.531 0.292,0.198 10 false RB 1.188,0.292 1.438,0.5 0.25,0.208 10 false RL 0.917,0.365 1.156,0.583 0.24,0.219 10 false B 2.313,1.74 2.521,1.938 0.208,0.198 10 false IG

Disconnect the park/neutral position switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (RB) - 2 (RL) Shift lever in R Below 1 Ω
1 (RB) - 2 (RL) Shift lever not in R 10 kΩ or higher
3 (B) - 2 (RL) Shift lever in P, R, N, D and S 10 kΩ or higher
6 (IG) - 2 (RL) Shift lever in P, R, N, D and S 10 kΩ or higher


Text in Illustration
*a Component without harness connected
(Park/Neutral Position Switch Assembly)



OK

3.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - TCM)

NG

3.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - TCM)
a.

Disconnect the C24 park/neutral position switch assembly connector.


b.

Disconnect the A82 TCM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C24-2 (RL) - A82-5 (R) Always Below 1 Ω
C24-2 (RL) or A82-5 (R) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR