Home › Drivetrain › AE80F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM › from 2015.08
RM2660E _52 Drivetrain _052807 AE80F AUTOMATIC TRANSMISSION / TRANSAXLE _0255308 AUTOMATIC TRANSMISSION SYSTEM C

AE80F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  P0500  Vehicle Speed Sensor  


DESCRIPTION

The speed sensor detects the wheel speed and sends the appropriate signals to the skid control ECU. The skid control ECU converts these wheel speed signals into a pulse signal and outputs it to the TCM via the combination meter. The TCM determines the vehicle speed based on the frequency of this pulse signal.

DTC Code DTC Detection Condition
1.

Diagnosis Condition

2.

Malfunction Status

3.

Malfunction Time

4.

Other


Trouble Area
P0500
1.

Transmission revolution sensor (SP2) value is 9 km/h (5.59 mph) or more

2.

Vehicle speed signal is not input

3.

5 seconds or more

4.

2-trip detection logic


·

Open or short in vehicle speed signal circuit

·

Combination meter system

·

Skid control ECU (master cylinder solenoid)

·

TCM



MONITOR DESCRIPTION

The TCM assumes that the vehicle is being driven when the indicated vehicle speed is more than 9 km/h (5.59 mph). If there is no speed signal from the combination meter despite this condition being met, the TCM interprets this as a malfunction in the speed signal circuit. The TCM then illuminates the MIL and stores the DTC.

WIRING DIAGRAM

C345400E02
5.744,2.15 6.289,2.320 0.545,0.170 10 A82 5.24,1.23 5.784,1.400 0.545,0.170 10 SPD 4.957,1.23 5.219,1.400 0.262,0.170 10 18 3.898,1.23 4.160,1.400 0.262,0.170 10 6 3.578,1.23 3.841,1.400 0.262,0.170 10 +S 2.237,2.15 2.633,2.320 0.397,0.170 10 E119 2.237,2.304 4.305,2.474 2.068,0.170 10 Combination Meter Assembly 5.744,2.304 6.289,2.474 0.545,0.170 10 TCM 4.758,2.974 6.062,3.144 1.304,0.170 10 to Other ECUs 1.699,1.316 1.961,1.486 0.262,0.170 10 12 2.271,1.316 2.534,1.486 0.262,0.170 10 5 2.492,1.316 2.755,1.486 0.262,0.170 10 SI 1.313,1.423 1.723,1.593 0.410,0.170 10 SP1 0.534,2.15 0.963,2.320 0.429,0.170 10 A24 0.534,2.304 1.730,2.877 1.196,0.573 10 Skid Control ECU (Master Cylinder Solenoid)

CAUTION / NOTICE / HINT

NOTICE:

Perform registration and/or initialization when parts related to the automatic transmission are replaced (See page Drivetrain>AE80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM>INITIALIZATION).


HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

Turn the engine switch on (IG) and wait for 3 seconds or more.*1

2.

Drive the vehicle at 9 km/h (5.59 mph) or more for 5 seconds or more.*2

3.

Turn the engine switch off.

4.

Perform steps (*1) through (*2) again.



PROCEDURE

1.CHECK OPERATION OF SPEEDOMETER
a.

Drive the vehicle and check whether the operation of the speedometer in the combination meter is normal.

HINT:
·

The vehicle speed sensor is operating normally if the speedometer reading is normal.

·

If the speedometer does not operate, check it by following the procedure described in Speedometer Malfunction (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>Speedometer Malfunction).





OK

2.READ VALUE USING GTS (VEHICLE SPEED)

NG

2.READ VALUE USING GTS (VEHICLE SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / ECT / Data List / Vehicle Speed.


e.

Drive the vehicle.


f.

In accordance with the display on the GTS, read the Data List.

ECT
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Vehicle Speed Vehicle speed/
Min.: 0 km/h (0 mph)
Max.: 255 km/h (158 mph)
Actual vehicle speed -

OK:

Vehicle speed displayed on GTS and speedometer display are equal.




OK

NG

3.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - TCM)
3.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - TCM)
a.

Disconnect the E119 combination meter assembly connector.


b.

Disconnect the A82 TCM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E119-6 (+S) - A82-18 (SPD) Always Below 1 Ω
E119-6 (+S) or A82-18 (SPD) - Body ground Always 10 kΩ or higher


HINT:

If the wire harness has a short, check the speed signal circuit in other systems related to the vehicle speed signal (e.g. SFI system, audio system, etc.).




OK

4.CHECK COMBINATION METER ASSEMBLY (+S VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (OTHER SYSTEMS RELATED TO SPEED SIGNAL)

4.CHECK COMBINATION METER ASSEMBLY (+S VOLTAGE)
a.
U164969E02
1.156,1.156 0.958,1.635 false 0.125,0.063 0.406,0.24 0.281,0.177 10 false *a 0.802,1.677 1.167,1.865 0.365,0.188 10 false +S 1.563,0.219 1.917,0.396 0.354,0.177 10 false E119

Disconnect the combination meter connector.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E119-6 (+S) - Body ground Engine switch on (IG) 4.5 to 5.5 V


Text in Illustration
*a Front view of wire harness connector
(to Combination Meter Assembly)



OK

5.INSPECT COMBINATION METER ASSEMBLY (SPD SIGNAL OUTPUT WAVEFORM)

NG

5.INSPECT COMBINATION METER ASSEMBLY (SPD SIGNAL OUTPUT WAVEFORM)
a.
U165724E02
2.104,1.688 2.448,2.271 false 0.125,0.052 0.406,0.229 0.281,0.177 10 false *a 2.385,2.313 2.708,2.5 0.323,0.188 10 false +S 0.219,1.531 0.573,1.708 0.354,0.177 10 false E119 0.073,2.802 0.729,2.99 0.656,0.188 10 false 0 to 5 V 0.396,4.104 0.76,4.292 0.365,0.188 10 false 0 V 1.583,4.135 2.479,4.323 0.896,0.188 10 false Turn Wheel

Remove the combination meter.


b.

Connect the combination meter connector.


c.

Move the shift lever to the neutral position.


d.

Jack up the vehicle.


e.

Turn the engine switch on (IG).


f.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E119-6 (+S) - Body ground Engine switch on (IG)
(Turn wheel slowly)
Voltage generated intermittently

Text in Illustration
*a Component with harness connected
(Combination Meter Assembly)


HINT:

The output voltage should fluctuate up and down, similarly to the diagram, when the wheel is turned slowly.




OK

NG

6.CHECK COMBINATION METER ASSEMBLY (SPD SIGNAL INPUT WAVEFORM)
6.CHECK COMBINATION METER ASSEMBLY (SPD SIGNAL INPUT WAVEFORM)
a.
U165725E02
2.188,1.688 2.531,2.271 false 0.125,0.073 0.406,0.25 0.281,0.177 10 false *a 2.479,2.271 2.802,2.458 0.323,0.188 10 false SI 0.219,1.521 0.573,1.698 0.354,0.177 10 false E119 0.063,2.781 0.719,2.969 0.656,0.188 10 false 0 to 5 V 0.396,4.104 0.76,4.292 0.365,0.188 10 false 0 V 1.583,4.135 2.479,4.323 0.896,0.188 10 false Turn Wheel

Remove the combination meter.


b.

Connect the combination meter connector.


c.

Move the shift lever to the neutral position.


d.

Jack up the vehicle.


e.

Turn the engine switch on (IG).


f.

Check the voltage between the body ground while the wheel is turned slowly.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E119-5 (SI) - Body ground Engine switch on (IG)
(Turn wheel slowly)
Voltage generated intermittently

Text in Illustration
*a Component with harness connected
(Combination Meter Assembly)


HINT:

The output voltage should fluctuate up and down, similarly to the diagram, when the wheel is turned slowly.




OK

REPLACE COMBINATION METER ASSEMBLY

NG

7.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - SKID CONTROL ECU)
7.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - SKID CONTROL ECU)
a.

Disconnect the E119 combination meter connector.


b.

Disconnect the A24 skid control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E119-5 (SI) - A24-12 (SP1) Always Below 1 Ω
E119-5 (SI) or A24-12 (SP1) - Body ground Always 10 kΩ or higher




OK

REPLACE SKID CONTROL ECU (MASTER CYLINDER SOLENOID)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR