Home › Drivetrain › AE80F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM › 2015.08–2017.08
RM2660E _52 Drivetrain _052807 AE80F AUTOMATIC TRANSMISSION / TRANSAXLE _0255308 AUTOMATIC TRANSMISSION SYSTEM C

AE80F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM  P076B  Shift Solenoid "H" Performance/Stuck Off  


SYSTEM DESCRIPTION

Based on signals from the transmission revolution sensors (NT and SP2), the actual gear is detected.

If the detected gear is different than the commanded gear, the TCM detects related mechanical problems in the shift solenoid valves, transmission valve body assembly and automatic transmission assembly (clutch, brake, gear, etc.).

HINT:

Actual gear when a malfunction occurs in shift solenoid valve SC1 (without fail-safe control):

TCM commanded gear 1st 2nd 3rd 4th 5th 6th 7th 8th
Actual gear during SC1 stuck OFF malfunction 1st 2nd 3rd 4th 5th 4th or 6th 3rd or 7th 2nd or 8th


DTC No. DTC Detection Condition
1.

Diagnosis Condition

2.

Malfunction Status

3.

Malfunction Time

4.

Other


Trouble Area
P076B
1.

Battery voltage is 9.5 V or higher, engine speed is more than 400 rpm, and the vehicle is driven with the shift lever in D (no malfunctions are detected in shift solenoid valve SC1, SC2, SL1, SL2, SL3, SL4, SL5, SLT, SLU, park/neutral position switch assembly, TCM, electronic throttle, knock control sensor, No. 1 ATF temperature sensor, transmission revolution sensors (NT), and CAN communication system)

2.

One of the following occurs:

(a) When gear shifts to 6th are requested by TCM, actual gear changes to 4th gear.

(b) When gear shifts to 7th are requested by TCM, actual gear changes to 3rd gear.

(c) When gear shifts to 8th are requested by TCM, actual gear changes to 2nd gear.

3.

Malfunction status is detected 5 times per trip

4.

2 trip detection logic


·

Shift solenoid valve SC1

·

Shift solenoid valve SL1

·

Transmission valve body assembly

·

Automatic transmission assembly (clutch, brake, gear, etc.)



MONITOR DESCRIPTION

This DTC indicates a "stuck OFF" malfunction of shift solenoid valve SC1.

The TCM commands gear shifts by turning the shift solenoid valves on or off. When the gear position commanded by the TCM and the actual gear position are not the same, the TCM stores the DTC.

CAUTION / NOTICE / HINT

NOTICE:

Perform registration and/or initialization when parts related to the automatic transmission are replaced (See page Drivetrain>AE80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM>INITIALIZATION).


HINT:

After performing repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

Perform the D Position Shift Test in Road Test (See page Drivetrain>AE80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM>ROAD TEST).*1

2.

Turn the engine switch off.

3.

Perform step (*1) again.



PROCEDURE

1.CHECK DTC OUTPUT (IN ADDITION TO DTC P076B)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / ECT / Trouble Codes.


e.

Read the DTCs using the GTS.

Result
Result Proceed to
DTC P076B and DTC P0746, P076C, P0776, P0796, P08CD, P08CE, P2714, P2808 and/or P2817 are output A
Only DTC P076B is output
DTCs other than P0746, P076B, P076C, P0776, P0796, P08CD, P08CE, P2714, P2808 and P2817 are also output B

HINT:

If DTCs other than P0746, P076B, P076C, P0776, P0796, P08CD, P08CE, P2714, P2808 and P2817 are output, perform troubleshooting for those DTCs first.




A

2.INSPECT SHIFT SOLENOID VALVE SC1

B

2.INSPECT SHIFT SOLENOID VALVE SC1
a.
C342509E01
0.122,0.053 0.425,0.245 0.303,0.192 10 *1 2.873,0.032 3.175,0.223 0.303,0.192 10 (+) 2.054,0.032 2.357,0.223 0.303,0.192 10 (-)

Remove the shift solenoid valve SC1 (See page Drivetrain>AE80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>VALVE BODY ASSEMBLY>DISASSEMBLY).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Shift solenoid valve SC1 connector - Shift solenoid valve SC1 body 20°C (68°F) 11 to 15 Ω



c.

Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

OK:
Measurement Condition Specified Condition
·

Battery positive (+) → Shift solenoid valve SC1 connector

·

Battery negative (-) → Shift solenoid valve SC1 body


Valve moves and makes an operating noise



Text in Illustration
*1 Shift Solenoid Valve SC1


OK

3.INSPECT SHIFT SOLENOID VALVE SL1

NG

3.INSPECT SHIFT SOLENOID VALVE SL1
a.
C209928E13
0.057,0.005 0.374,0.207 0.317,0.202 10 *a 1.757,0.949 2.207,0.361 false 2.238,0.194 2.402,0.396 0.164,0.202 10 1 1.506,0.949 1.056,0.361 false 0.918,0.194 1.082,0.396 0.164,0.202 10 2 1.757,2.945 2.207,2.358 false 2.238,2.191 2.402,2.393 0.164,0.202 10 1 1.506,2.945 1.056,2.358 false 0.918,2.191 1.082,2.393 0.164,0.202 10 2 1.923,3.928 2.122,4.130 0.200,0.202 10 (-) 1.119,3.928 1.339,4.130 0.221,0.202 10 (+)

Remove the shift solenoid valve SL1 (See page Drivetrain>AE80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>VALVE BODY ASSEMBLY>DISASSEMBLY).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Terminal 1 of the shift solenoid valve SL1 - Terminal 2 20°C (68°F) 5.0 to 5.6 Ω



c.

Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

OK:
Measurement Condition Specified Condition
·

Battery positive (+) with a 21 W bulb → Terminal 2

·

Battery negative (-) → Terminal 1


Valve moves and makes an operating noise



Text in Illustration
*1 Shift Solenoid Valve SL1


OK

4.INSPECT TRANSMISSION VALVE BODY ASSEMBLY

NG

4.INSPECT TRANSMISSION VALVE BODY ASSEMBLY
a.

Check the transmission valve body assembly (See page Drivetrain>AE80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>VALVE BODY ASSEMBLY>REMOVAL).

OK:

There is no foreign matter on each valve and they operate smoothly.




OK

REPAIR OR REPLACE AUTOMATIC TRANSMISSION ASSEMBLY

NG

REPAIR OR REPLACE TRANSMISSION VALVE BODY ASSEMBLY