Home › Drivetrain › AE80F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION ASSEMBLY › from 2015.08
RM2660E _52 Drivetrain _052807 AE80F AUTOMATIC TRANSMISSION / TRANSAXLE _0255296 AUTOMATIC TRANSMISSION ASSEMBLY A

AE80F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION ASSEMBLY  REMOVAL  


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 37140 3.REMOVE FRONT PROPELLER SHAFT ASSEMBLY

Hide 37110 4.REMOVE PROPELLER SHAFT ASSEMBLY

Hide 28100 6.REMOVE STARTER ASSEMBLY

Hide 53806 8.REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH

Hide 53805 9.REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH

Hide 51405A 10.REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

Hide 51440 12.REMOVE OIL PAN PROTECTOR ASSEMBLY

C171483

a.

Remove the 4 bolts and oil pan protector assembly.


Hide 53782 16.REMOVE FRONT FENDER APRON SEAL FRONT RH

Hide 53783 17.REMOVE FRONT FENDER APRON SEAL REAR RH

Hide 33702B 20.DISCONNECT FLOOR SHIFT GEAR SHIFTING ROD SUB-ASSEMBLY

C329048

a.

Remove the clip and pin and disconnect the floor shift gear shifting rod sub-assembly from the transmission control shaft lever.


Hide 32101A 23.REMOVE DRIVE PLATE AND TORQUE CONVERTER SETTING BOLT

a.
A163778E01
0.9,1.607 1.201,1.763 0.302,0.156 10 SST 0.831,1.237 1.049,1.572 1.049,1.572 1.089,1.108 false

Using SST, hold the crankshaft.

SST
09213-70011  (09213-70020)
09330-00021  


b.
C329069

Remove the 6 drive plate and torque converter setting bolts.

HINT:

Turn the crankshaft to remove the 6 drive plate and torque converter setting bolts.



Hide 32907A 24.DISCONNECT OIL COOLER TUBE

a.
C329078

Using a 17 mm union nut wrench, disconnect the 2 oil cooler tubes from the oil cooler tube union.


b.
C329080

Remove the 3 bolts and disconnect the oil cooler tube.


c.

Remove the bolt and transmission oil cooler tube clamp sub-assembly.


Hide 25.DISCONNECT GROUND CABLE

a.
C340169

Remove the bolt and disconnect the ground cable.


Hide 35000 26.SUPPORT AUTOMATIC TRANSMISSION ASSEMBLY

a.
C329070

Support the transmission with a transmission jack. Lift the transmission slightly from the No. 3 frame crossmember sub-assembly.

NOTICE:

Support the oil pan bolts to prevent damage to the oil pan gasket.



Hide 51203 27.REMOVE NO. 2 FRAME CROSSMEMBER SUB-ASSEMBLY

a.
C329071

w/ Cover:

Remove the engine mounting hole cover.


b.
C329072

Remove the 4 bolts of the rear No. 1 engine mounting insulator.


c.
C329073

Remove the 4 nuts, 4 bolts and No. 2 frame crossmember sub-assembly.


Hide 12371 28.REMOVE REAR NO. 1 ENGINE MOUNTING INSULATOR

a.
C329074

Remove the 2 bolts and engine mounting heat insulator.


b.

Remove the 4 bolts and rear No. 1 engine mounting insulator from the transmission.


Hide 29.DISCONNECT WIRE HARNESS AND CONNECTOR

a.
C329075

Tilt the transmission downward.

NOTICE:
·

Support the oil pan bolts to prevent damage to the oil pan gasket.


·

Make sure the cooling fan does not contact the fan shroud.




b.
C340131

Disconnect the transfer breather hose sub-assembly from the automatic transmission assembly.


c.

Detach the 6 clamps, 2 hose plugs and disconnect the transfer breather hose sub-assembly.


d.

Disconnect the park/neutral position switch connector, 2 transmission wire connectors and 3 transfer control connectors.

C340129

HINT:

Detach the claw, pull the lever, and then disconnect the transmission wire connector.



e.

Detach the 17 clamps and disconnect the wire harness.


Hide 35000 31.REMOVE AUTOMATIC TRANSMISSION ASSEMBLY

C329081

a.

Remove the 10 bolts and automatic transmission assembly.

NOTICE:

Do not use excess force to pry off the automatic transmission assembly.



Hide 32.REMOVE WIRE HARNESS CLAMP BRACKET

a.

Remove the 11 bolts and 11 wire harness clamp brackets.

C340130


Hide 32000 33.REMOVE TORQUE CONVERTER ASSEMBLY

a.
C341893E01
0.61,0.239 0.902,0.451 0.291,0.211 10 *a 1.31,0.463 0.837,0.354 0.837,0.354 1.435,0.682 false

Put matchmarks on the automatic transmission case sub-assembly and the torque converter assembly.

Text in Illustration
*a Matchmarks


b.

Remove the torque converter assembly from the automatic transmission assembly.

NOTICE:

Remove the torque converter assembly from the input shaft horizontally.