Based on signals from the transmission revolution sensors (NT and SP2), the actual gear is detected.
If the detected gear is different than the commanded gear, the TCM detects related mechanical problems in the shift solenoid valves, transmission valve body assembly and automatic transmission assembly (clutch, brake, gear, etc.).
Actual gear when a malfunction occurs in shift solenoid valve SC2 (without fail-safe control):
| TCM commanded gear | 1st | 2nd | 3rd | 4th | 5th | 6th | 7th | 8th |
| Actual gear during SC2 stuck ON malfunction* | 1st | 2nd | 3rd | 4th | 5th | 6th | 7th | 8th |
*: Vehicle does not move with shift lever in R
| DTC No. | DTC Detection Condition
1.
Diagnosis Condition 2.
Malfunction Status 3.
Malfunction Time 4.
Other |
Trouble Area |
|---|---|---|
| P08CE | 1.
Battery voltage is 9.5 V or higher, engine speed is more than 400 rpm, and the vehicle is driven with the shift lever in R (no malfunctions are detected in shift solenoid valve SC1, SC2, SL1, SL2, SL3, SL4, SL5, SLT, SLU, park/neutral position switch assembly, TCM, electronic throttle, knock control sensor, No. 1 ATF temperature sensor, transmission revolution sensors (NT), and CAN communication system) 2.
The engine overruns (neutral status). 3.
Malfunction status is detected 3 times per trip 4.
2-trip detection logic |
·
Shift solenoid valve SC2 ·
Shift solenoid valve SL3 ·
Shift solenoid valve SLT ·
Transmission valve body assembly ·
Automatic transmission assembly (clutch, brake, gear, etc) |
This DTC indicates a "stuck ON" malfunction of shift solenoid valve SC2.
When the vehicle does not move with the shift lever in R, the TCM stores the DTC.
Perform registration and/or initialization when parts related to the automatic transmission are replaced (See page Drivetrain>AE80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM>INITIALIZATION).
After performing repair, clear the DTCs and perform the following procedure to check that DTCs are not output.
Start the engine.*1
Drive the vehicle backward with the shift lever in R.*2
Turn the engine switch off.
Perform steps (*1) through (*2) again.
Check for DTCs again (See page Drivetrain>AE80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM>DTC CHECK / CLEAR).
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / ECT / Trouble Codes.
Read the DTCs using the GTS.
| Result | Proceed to |
|---|---|
| DTC P08CE and DTC P0746, P076B, P076C, P0776, P0796, P08CD, P2714, P2808 and/or P2817 are output | A |
| Only DTC P08CE is output | B |
| DTCs other than P0746, P076B, P076C, P0776, P0796, P08CD, P08CE, P2714, P2808 and P2817 are also output | C |
If DTCs other than P0746, P076B, P076C, P0776, P0796, P08CD, P08CE, P2714, P2808 and P2817 are output, perform troubleshooting for those DTCs first.
A
B
C
Clear the DTCs (See page Drivetrain>AE80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM>DTC CHECK / CLEAR).
Write down the currently output DTCs before clearing them.
Perform the stall speed test (See page Drivetrain>AE80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM>MECHANICAL SYSTEM TESTS).
| Test Condition | Proceed to |
|---|---|
| Stall speed test can be performed | A |
| Stall speed test cannot be performed | B |
A
B
Remove the shift solenoid valve SC2 (See page Drivetrain>AE80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>VALVE BODY ASSEMBLY>DISASSEMBLY).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Terminal of shift solenoid valve SC2 connector - Shift solenoid valve SC2 body | 20°C (68°F) | 11 to 15 Ω |
Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.
| Measurement Condition | Specified Condition |
|---|---|
·
Battery positive (+) → Shift solenoid valve SC2 connector ·
Battery negative (-) → Shift solenoid valve SC2 body |
Valve moves and makes an operating noise |
| *1 | Shift Solenoid Valve SC2 |
OK
NG
Remove the shift solenoid valve SL3 (See page Drivetrain>AE80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>VALVE BODY ASSEMBLY>DISASSEMBLY).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Terminal 1 of the shift solenoid valve SL3 - Terminal 2 | 20°C (68°F) | 5.0 to 5.6 Ω |
Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.
| Measurement Condition | Specified Condition |
|---|---|
·
Battery positive (+) with a 21 W bulb → Terminal 2 ·
Battery negative (-) → Terminal 1 |
Valve moves and makes an operating noise |
| *1 | Shift Solenoid Valve SL3 |
OK
NG
Remove the shift solenoid valve SLT (See page Drivetrain>AE80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>VALVE BODY ASSEMBLY>DISASSEMBLY).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Terminal 1 of the shift solenoid valve SLT - Terminal 2 | 20°C (68°F) | 5.0 to 5.6 Ω |
Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.
| Measurement Condition | Specified Condition |
|---|---|
·
Battery positive (+) with a 21 W bulb → Terminal 2 ·
Battery negative (-) → Terminal 1 |
Valve moves and makes an operating noise |
| *1 | Shift Solenoid Valve SLT |
OK
NG
Check the transmission valve body assembly (See page Drivetrain>AE80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>VALVE BODY ASSEMBLY>REMOVAL).
There is no foreign matter on each valve and they operate smoothly.
OK
(See pageDrivetrain>AE80F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION ASSEMBLY>REMOVAL)
NG