Home › Drivetrain › JF2A (TRANSFER / 4WD / AWD) › TRANSFER SYSTEM › from 2015.08
RM2660E _52 Drivetrain _052810 JF2A TRANSFER / 4WD / AWD _0255329 TRANSFER SYSTEM J

JF2A TRANSFER / 4WD / AWD  TRANSFER SYSTEM  Clutch Switch Circuit  


DESCRIPTION

While depressing the clutch pedal, the clutch start switch assembly sends a signal to terminal MTN of the 4 wheel drive control ECU. While the signal is input, switching between H4 and L4 is possible.

WIRING DIAGRAM

C326384E06
1.656,3.094 3.656,3.302 2,0.208 10 false Clutch Start Switch Assembly 0.375,2.458 1.135,2.844 0.76,0.385 10 false to ST Relay 0.813,0.271 2.042,0.469 1.229,0.198 10 false from ECM 0.781,0.698 2.604,1.094 1.823,0.396 10 false from Certification ECU (Smart Key ECU Assembly)*1 0.115,3.333 2.542,3.521 2.427,0.188 10 false *1: w/ Smart Entry and Start System 3.542,2.365 3.698,2.563 0.156,0.198 10 false 1 1.813,2.365 1.969,2.563 0.156,0.198 10 false 2 1.656,2.927 2.573,3.115 0.917,0.188 10 false A49*3, e1*4 4.792,3.396 6.51,3.604 1.719,0.208 10 false 4 Wheel Drive Control ECU 4.802,3.177 5.26,3.375 0.458,0.198 10 false A27 5.125,2.302 5.583,2.5 0.458,0.198 10 false MTN 6.104,1.688 6.417,1.885 0.313,0.198 10 false IG 4.896,2.333 5.208,2.531 0.313,0.198 10 false 18 0.813,1.281 2.219,1.469 1.406,0.188 10 false from Ignition Switch*2 0.115,3.573 2.448,3.771 2.333,0.198 10 false *2: w/o Smart Entry and Start System

PROCEDURE

1.READ VALUE USING GTS (CLUTCH START SWITCH)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the GTS on.


d.

Turn the ignition switch to ON.


e.

Enter the following menus: Powertrain / Four Wheel Drive / Data List.


f.

According to the display on the GTS, read the Data List.

Four Wheel Drive
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Clutch SW Clutch start switch status
ON or OFF
ON: Clutch pedal depressed
OFF: Clutch pedal released
Used only for vehicles with a manual transmission.
Displays OFF for vehicles with an automatic transmission.

OK:

The display changes according to the clutch pedal operation.




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK ENGINE CONTROL SYSTEM
2.CHECK ENGINE CONTROL SYSTEM
a.

Check that the engine control system operates normally.

for 1VD-FTV (w/o DPF): See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

for 1GR-FE: See page

OK:

Engine control system operates normally.


Result:
Result Proceed to
OK A
NG (for 1VD-FTV (w/o DPF)) B
NG (for 1GR-FE) C



Click hereEngine / Hybrid System>1VD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/o DPF)>HOW TO PROCEED WITH TROUBLESHOOTING


A

3.CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU - CLUTCH START SWITCH ASSEMBLY)

B

C

3.CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU - CLUTCH START SWITCH ASSEMBLY)
a.

Disconnect the A27 4 wheel drive control ECU connector.


b.

for LHD:

Disconnect the A49 clutch start switch assembly connector.


c.

for RHD:

Disconnect the e1 clutch start switch assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD:
Tester Connection Condition Specified Condition
A27-18 (MTN) - A49-1 Always Below 1 Ω
A27-18 (MTN) or A49-1 - Body ground Always 10 kΩ or higher

for RHD:
Tester Connection Condition Specified Condition
A27-18 (MTN) - e1-1 Always Below 1 Ω
A27-18 (MTN) or e1-1 - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR