Home › Drivetrain › JF2A (TRANSFER / 4WD / AWD) › TRANSFER SYSTEM › from 2015.08
RM2660E _52 Drivetrain _052810 JF2A TRANSFER / 4WD / AWD _0255329 TRANSFER SYSTEM T

JF2A TRANSFER / 4WD / AWD  TRANSFER SYSTEM  PROBLEM SYMPTOMS TABLE  


HINT:
·

Use the table below to help determine the cause of problem symptoms. If multiple suspected areas are listed, the potential causes of the symptoms are listed in order of probability in the "Suspected Area" column of the table. Check each symptom by checking the suspected areas in the order they are listed. Replace parts as necessary.

·

Inspect the fuses and relays related to this system before inspecting the suspected areas below.



Transfer System
Symptom Suspected Area See page
Noise Oil (Level low) (Click here)
Oil (Wrong) (Click here)
Transfer faulty (Click here)
Oil leakage Oil (Level too high) (Click here)
Gasket (Damaged) (Click here)
Oil seal (Worn or damaged) (Click here)
O-ring (Worn or damaged) (Click here)
The 4LO indicator light remains off after operating the transfer position switch (integration control and panel assembly) to L4*4
The 4LO indicator light remains off after operating the transfer position switch to L4*5, *6
ECU power source circuit (Click here)
Clutch switch circuit*1 (Click here)
CAN communication system (Click here)
Combination meter assembly
Transfer position switch (integration control and panel assembly) *4
Transfer position switch*5, *6
4 wheel drive control ECU
The 4LO indicator light remains on after operating the transfer position switch (integration control and panel assembly) to H4*4
The 4LO indicator light remains on after operating the transfer position switch to H4*5, *6
ECU power source circuit (Click here)
Clutch switch circuit*1 (Click here)
CAN communication system (Click here)
Combination meter assembly
Transfer position switch (integration control and panel assembly)*4
Transfer position switch*5, *6
4 wheel drive control ECU
The 4LO indicator light continues blinking after the transfer position switch (integration control and panel assembly) is operated*4
The 4LO indicator light continues blinking after the transfer position switch is operated*5, *6
ECU power source circuit (Click here)
Temperature sensor circuit*3 (Click here)
Temperature sensor*3 (Click here)
High-low transfer shift motor (Click here)
High-low transfer limit switch or neutral position detection switch*1
4 wheel drive control ECU
After the center differential lock switch (integration control and panel assembly) is operated, the center differential lock indicator light remains off or illuminated*4
After the center differential lock switch is operated, the center differential lock indicator light remains off or illuminated*5, *6
ECU power source circuit (Click here)
CAN communication system (Click here)
Combination meter assembly
Center differential lock switch (integration control and panel assembly)*4
Center differential lock switch*5, *6
4 wheel drive control ECU
After the center differential lock switch (integration control and panel assembly) is operated, the center differential lock indicator light remains blinking*4
After the center differential lock switch is operated, the center differential lock indicator light remains blinking*5, *6
ECU power source circuit (Click here)
Center differential lock shift motor (Click here)
Center differential lock limit switch or center differential lock detection switch
4 wheel drive control ECU
After the rear differential lock switch is operated, the rear differential lock indicator light remains off or illuminated*2 ECU power source circuit (Click here)
Differential lock switch (Click here)
CAN communication system
Combination meter assembly
4 wheel drive control ECU
After the rear differential lock switch is operated, the rear differential lock indicator light remains blinking*2 ECU power source circuit (Click here)
Differential lock shift motor (Click here)
Limit switch or rear differential lock position switch
4 wheel drive control ECU

*1: for Manual Transmission

*2: w/ Rear Differential Lock

*3: w/ Temperature Sensor

*4: for Automatic Transmission w/ Entry and Start System

*5: for Manual Transmission w/ Entry and Start System

*6: w/o Entry and Start System