Home › Drivetrain › JF2A (TRANSFER / 4WD / AWD) › TRANSFER SYSTEM › from 2015.08
RM2660E _52 Drivetrain _052810 JF2A TRANSFER / 4WD / AWD _0255329 TRANSFER SYSTEM J

JF2A TRANSFER / 4WD / AWD  TRANSFER SYSTEM  Rear Differential Lock Switch Circuit  


WIRING DIAGRAM

C339930E02
3.485,2.647 3.894,2.883 0.409,0.236 10 A27 0.561,2.521 2.115,2.732 1.554,0.211 10 Differential Lock Switch 0.561,2.315 1.023,2.541 0.461,0.225 10 E87 0.916,1.736 1.183,2.003 0.267,0.267 10 R 2.149,1.755 2.472,1.975 0.323,0.221 10 IG 2.439,1.755 2.604,1.966 0.165,0.211 10 1 0.664,1.764 0.866,2.003 0.202,0.239 10 4 0.916,3.305 2.730,3.526 1.813,0.221 10 : CAN Communication Line 3.471,2.862 5.377,3.073 1.906,0.211 10 4 Wheel Drive Control ECU 3.391,1.764 3.649,1.948 0.258,0.184 10 15 3.69,1.764 3.993,1.931 0.303,0.167 10 R 4.424,0.821 4.765,1.060 0.341,0.239 10 IG 5.745,2.661 6.938,3.131 1.193,0.471 10 Combination Meter Assembly

PROCEDURE

1.CHECK REAR DIFFERENTIAL LOCK INDICATOR LIGHT
a.

Turn the ignition switch to ON.


b.

Press the differential lock switch.


c.

Check the rear differential lock indicator light.

Result:
Result Proceed to
Rear differential lock indicator light blinks or illuminates A
Rear differential lock indicator light remains off regardless of switch operation B
Rear differential lock indicator light remains illuminated regardless of switch operation C


Blinking: Blinks at 0.5 second intervals (0.5 seconds on and 0.5 seconds off)




A

END

B

2.CHECK CAN COMMUNICATION LINE

C

7.CHECK CAN COMMUNICATION LINE
2.CHECK CAN COMMUNICATION LINE
a.

Select "Bus Check" from the System Selection Menu screen, and follow the prompts on the screen to inspect the CAN bus (for LHD with Central Gateway ECU: See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for LHD with Central Gateway ECU)>DIAGNOSIS SYSTEM, for LHD without Central Gateway ECU: See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for LHD without Central Gateway ECU)>DIAGNOSIS SYSTEM, for RHD with Central Gateway ECU: See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for RHD with Central Gateway ECU)>DIAGNOSIS SYSTEM, for RHD without Central Gateway ECU: See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for RHD without Central Gateway ECU)>DIAGNOSIS SYSTEM).

OK:

"Bus Check" indicates no malfunctions in CAN communication.


Result
Result Proceed to
DTC is not output A
DTC is output for LHD with Central Gateway ECU B
for LHD without Central Gateway ECU C
for RHD with Central Gateway ECU D
for RHD without Central Gateway ECU E



A

3.READ VALUE USING GTS (DIFFERENTIAL LOCK SWITCH)

B

C

D

E

3.READ VALUE USING GTS (DIFFERENTIAL LOCK SWITCH)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the GTS on.


d.

Turn the ignition switch to ON.


e.

Enter the following menus: Powertrain / Four Wheel Drive / Data List.


f.

According to the display on the GTS, read the Data List

Four Wheel Drive
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Rear Differential Lock Control SW Differential lock switch status/
ON or OFF
ON: RR (LOCK)
OFF: OFF (FREE)
Used only for vehicles with a rear differential lock.
Always displays OFF for vehicles without a rear differential lock.

OK:

OK: Display changes according to differential lock switch operation




OK

4.INSPECT COMBINATION METER ASSEMBLY

NG

5.INSPECT DIFFERENTIAL LOCK SWITCH
4.INSPECT COMBINATION METER ASSEMBLY
a.

Turn the ignition switch off.


b.

Perform an Active Test of the combination meter assembly using the GTS (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST).


c.

Check the combination meter assembly.

OK:

The rear differential lock indicator light turns on or off in accordance with the GTS.


Result:
Result Proceed to
OK for LHD A
for RHD B
NG C




A

B

C

5.INSPECT DIFFERENTIAL LOCK SWITCH

b.

Inspect the differential lock switch (See page Drivetrain>AXLE AND DIFFERENTIAL>REAR DIFFERENTIAL LOCK POSITION SWITCH(w/ Differential Lock)>INSPECTION).

OK:

The differential lock switch operates normally.




OK

6.CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU -DIFFERENTIAL LOCK SWITCH)

NG

6.CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU -DIFFERENTIAL LOCK SWITCH)
a.

Disconnect the A27 4 wheel drive control ECU connector.


b.

Disconnect the E87 differential lock switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A27-15 (R) - E87-1 (IG) Always Below 1 Ω
E87-4 (R) - Body ground Always Below 1 Ω
A27-15 (R) or E87-1 (IG) - Body ground Always 10 kΩ or higher


Result:
Result Proceed to
OK for LHD A
for RHD B
NG C




A

B

B

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK CAN COMMUNICATION LINE
a.

Select "Bus Check" from the System Selection Menu screen, and follow the prompts on the screen to inspect the CAN bus (for LHD with Central Gateway ECU: See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for LHD without Central Gateway ECU)>DIAGNOSIS SYSTEM, for LHD without Central Gateway ECU: See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for RHD with Central Gateway ECU)>DIAGNOSIS SYSTEM, for RHD with Central Gateway ECU: See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for RHD without Central Gateway ECU)>DIAGNOSIS SYSTEM, for RHD without Central Gateway ECU: See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for LHD with Central Gateway ECU)>DIAGNOSIS SYSTEM).

OK:

"Bus Check" indicates no malfunctions in CAN communication.



Result
Result Proceed to
DTC is not output A
DTC is output for LHD with Central Gateway ECU B
for LHD without Central Gateway ECU C
for RHD with Central Gateway ECU D
for RHD without Central Gateway ECU E


A

8.READ VALUE USING GTS (REAR DIFFERENTIAL LOCK INDICATOR)

B

C

D

E

8.READ VALUE USING GTS (REAR DIFFERENTIAL LOCK INDICATOR)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the GTS on.


d.

Turn the ignition switch to ON.


e.

Enter the following menus: Powertrain / Four Wheel Drive / Data List


f.

According to the display on the GTS, read the Data List.

Four Wheel Drive
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Rear Differential Lock Indicator Request Rear differential lock indicator light request/
Blink3, Blink2, Blink1, ON or OFF
·

Blink3: Indicator light rapidly blinks

·

Blink2: Indicator light blinks 3 times

·

Blink1: Indicator light blinks

·

ON: Indicator light illuminates

·

OFF: Indicator light turns off


·

Blinking: 0.5 second intervals (0.5 seconds on and 0.5 seconds off)

·

Rapidly blinking: 0.25 second intervals (0.25 seconds on and 0.25seconds off)


Used only for vehicles with a rear differential lock.
Always displays OFF for vehicles without a rear differential lock.


g.

Turn the differential lock switch on and off several times and check the GTS display condition of the rear differential lock indicator light.

Result:
Result Proceed to
Data List continues to display ON even when differential lock switch is operated for LHD A
for RHD B
Data List display changes according to differential lock switch operation C




A

B

C